JB/T 5000.9-2007General technical requirements for heavy machinery - Part 9: Machined parts (English PDF)
重型机械通用技术条件 第9部分:切削加工件
This is a limited preview
Buy now to download the full PDF (15 pages)
Need quotation for your management?
Get a formal quotation for JB/T 5000.9-2007 in 30 minutes.
Issued by
MIIT
Level / Type
Industry · Recommended
Issue date
August 28, 2007
Implementation date
February 1, 2008
Scope
JB/T 5000.9-2007 is the English-translated version of 重型机械通用技术条件 第9部分:切削加工件.
JB/T 5000.9-2007 is the Chinese standard "General technical requirements for heavy machinery - Part 9: Machined parts".
Its scope clause reads: This part of JB/T 5000 specifies general requirements of cutting and tolerance without indication; and specific requirements on key groove, hole diameter and hole distance, center hole, tolerance without indication and allowed shape of cutter, etc. This part is applicable to cutting of heavy machinery product parts.
All the product drawings and technical documents, if without special requirements, shall meet the requirements of this part. Its clauses include general requirements; tolerance without indication; unnoted tolerance for symmetry of key groove; positional tolerancing without indication of threaded; thread; center hole; unnoted surface roughness.
Found what you need?
Document preview — JB/T 5000.9-2007
National Standard of the People's Republic of China
- Replacing
- JB/T 5000.9-1998
Issued by: Ministry of Industry and Information Technology of the People's Republic of China
Contents
- Foreword3
- 1 Scope5
- 2 Normative References5
- 3 General Requirements5
- 4 Tolerance without Indication7
- 4.2 Tolerance of Form and Position10
- 5 Unnoted Tolerance for Symmetry of Key Groove12
- 7 Thread14
- 8 Center Hole14
- 9 Unnoted Surface Roughness14
- 10 Requirements for Allowed Machining According to Shape of Cutter15
- 11 Rolling17
- 11.1 Methods and Purpose for Rolling17
- 11.2 Preparation for Rolling17
- 11.3 Rolled Surface17
1 Scope
This part of JB/T 5000 specifies general requirements of cutting and tolerance without indication; and specific requirements on key groove, hole diameter and hole distance, center hole, tolerance without indication and allowed shape of cutter, etc.
This part is applicable to cutting of heavy machinery product parts.
All the product drawings and technical documents, if without special requirements, shall meet the requirements of this part.
2 Normative References
The following documents contain provisions which, through reference in this text, constitute provisions of this part. For dated references, subsequent amendments to (excluding corrigendum), or revisions of, any of these publications do not apply. However, parties to agreements based on this standard are encouraged to investigate the possibility of applying the most recent editions of the standards. For undated references, the latest edition applies.
GB/T 3 Run-outs, Undercuts and Chamfers for General Purpose Metric Screw
Threads (GB/T 3-1997, eqv ISO 3508:1976, ISO 4755: 1983)
GB/T 197-2003 General Purpose Metric Screw Threads - Tolerances (ISO 965-1: 1998,
MOD)
GB/T 1184-1996 Geometrical Tolerance - Geometrical Tolerances for Features without
Individual Tolerance Indications (eqv ISO 2768-2: 1989)
GB/T 1804-2000 General Tolerances - Tolerances for Linear and Angular Dimensions without Individual Tolerance Indication (eqv ISO 2768-1:1989)
GB/T 5277-1985 Fasteners; Clearance Holes for Bolts and Screws (eqv ISO 273:1979)
3 General Requirements
3.1
The parts after machining shall meet the requirements of product drawing and technical document as well as this part.
3.2
Parts shall be subjected to inspection and acceptance according to procedures, and next procedure can start only after the previous procedure is qualified.
3.5
Parts after fine machining is not allowed to be placed directly on the ground, and
necessary support and protective measures shall be taken. The machined surface shall be free from rust as well as bumping, scratching and other defects that affect property, service life or appearance.
3.6
The fitting surface, friction surface, locating surface and other working surfaces after fine machining is not allowed to be with stamped with mark.
3.7
As for parts whose final procedure is heat treatment, after heat treatment, their surfaces shall be free from oxide skin after heat treatment. Fitting surface and tooth surface after fine machining shall be free from annealing, bluing, discoloration, etc.
4 Tolerance without Indication
4.1 Length Dimension, Rounding Radius and Chamfering Height, Angular
Dimension
4.1.1
Applicable Objects:
Size without tolerance indication between two cutting surfaces (size without tolerance indication of parts that are cut short through sawing shall be specified separately).
Size without tolerance indication is applicable to:
-- Length dimension, such as external dimension, internal dimension, step dimension, diameter and distance dimension.
-- Rounding radius and chamfering height.
-- Angular dimension, including dimension with angle indication and without angle indication, such as the angles of regular polygon.
-- Machining length and angular dimension of parts that are combined together.
Size without tolerance indication is not applicable to:
-- Auxiliary dimension in brackets.
4.2.3.2 Roundness, Cylindricity, Line Profile and Surface Profile
Form tolerances are limited by the dimensional tolerance range; unnoted tolerance of roundness, cylindricity, line profile and surface profile shall be less than the value of its unnoted dimensional tolerance.
4.2.4 Tolerance of Position
4.2.4.1 Tolerance of Parallelism
The straightness (flatness) of two parallel elements and the unnoted tolerance of size for their distance, whichever is larger shall be taken as the unnoted tolerance of parallelism. The unnoted tolerance of straightness (flatness) shall be subject to that of the longer one in the elements.
4.2.4.2 Tolerance of Perpendicularity
Unnoted tolerance of perpendicularity shall be in accordance with those specified in Table 7.
4.2.4.3 Tolerance of Inclination
Unnoted tolerance of inclination shall be in accordance with those specified in Table 5.
4.2.4.4 Tolerance of Symmetry
Unnoted tolerance of symmetry of non-rotating symmetry elements shall be in accordance with those specified in Table 8. Unnoted tolerance also applies if one of symmetry elements is rotating symmetry and another is non-rotating symmetry (such as, axle head and sleeve of universal shaft).
4.2.4.5 Tolerances of Coaxiality and Circular Run-out
Unnoted tolerance of coaxiality and circular run-out (radial direction, end surface and diagonal direction) shall be in accordance with those specified in Table 9.
5 Unnoted Tolerance for Symmetry of Key Groove
Unnoted tolerance for symmetry of key groove shall be in accordance with those specified in
Table 10.
6 Positional Tolerancing without Indication of Threaded
Hole and Unthreaded Hole
Table 11 is applicable to the threaded hole and unthreaded hole connected with bolt or screw;
hole diameter of unthreaded hole shall be given according to the moderate mounting dimension specified in GB/T 5277-1985; for positional tolerancing of coarse fit unthreaded hole, refer to this requirement.
Indication of positional tolerancing is excluded from accumulation of error. It means that each hole distance is the theoretical and correct coordinate dimension without deviation. Positional tolerancing without indication for cylinder of threaded hole and unthreaded hole shall be in accordance with these specified in Table 11.
7 Thread
7.1
Regular thread accuracy shall be in accordance with 6H/6g specified in GB/T 197-2003.
7.2
Size of run-outs, undercuts and chamfers for general-purpose metric screw threads shall
be in accordance with the requirements of GB/T 3.
7.3
The machined thread surface shall be free from casting skin, bumping, chasing, burr and other defects.
7.4
Before machining of thread, threading-in side of male and female thread must be chamfered, by 45° for male threads; by 60° for female threads. The depth of chamfer is equal to the height of teeth pattern.
7.5
Surface roughness of general-purpose metric screw threads shall not be greater than Ra
12.5µm for female threads or Ra 6.3µm for male threads.
8 Center Hole
8.1
It shall be indicated clearly that the center hole needs be reserved or removed in the drawing; otherwise it shall be considered that reservation or removal of center hole is allowed.
8.2
Types and size of center hole shall be subject to corresponding standard.
8.3 Surface roughness on conical surface of center hole
when used for rough machining, Ra value shall be not greater than 6.3µm; when used for fine machining, Ra value shall be not greater than 3.2µm; when used for processing of precision component, Ra value shall be not greater than 1.6µm.
9 Unnoted Surface Roughness
Surface roughness not indicated in the drawing shall be in accordance with the requirements in Table 12.
......
This preview omits tables, figures, formulas and parts of the technical clauses. The complete document — 15 pages — is available in the English PDF.
Referenced standards
Cited by
- NB/T 10525-2021Method of type symbolization for oil shale retorting furnace
- JB/T 10543-2018Rail fastenings for lifting and conveying rails
- JB/T 13399.2-2018Wide and heavy plate roughing mills - Part 2: General technical specifications
- JB/T 13402.2-2018Tandem cold rolling mills - Main mill - Part 2: General technical requirements
- JB/T 13403.2-2018Hot strip finishing mills - Part 2: General technical requirements
- JB/T 13404-2018Bar rolling lines - Cold shears
Similar standards
Editions of JB/T 5000.9
| Edition | Title | Revision | Status |
|---|---|---|---|
| JB/T 5000.9-2007 | General technical requirements for heavy machinery - Part 9: Machined parts | current edition | Current |
| JB/T 5000.9-1998 | General technical requirements for heavy machinery - Part 9: Machined parts | previous edition | Superseded |
This page sells the current edition, JB/T 5000.9-2007. Earlier editions are listed for reference only.
How to Download JB/T 5000.9-2007
- 1
Add to cart
Click "Download PDF" on this page and choose "Buy this standard". You can add more standards before checkout.
- 2
Checkout
Enter your email and billing details. Payment is processed securely by Stripe (cards or bank transfer). Prefer bank details? Request a quotation (min. order $300).
- 3
Fast delivery
After payment you'll receive an email confirmation. The English PDF is sent to the same address, usually within minutes and at the latest within 1 business day.
- 4
Invoice included
A tax invoice is attached to the confirmation email. Need a custom invoice? Contact us.
Related Standards
JB/T 5000.10-2007 — General technical requirements for heavy machinery - Part 10: Assembly
JB/T 5000.8-1998 — The heavy mechanical general techniques and standards. Forging
JB/T 5000.10-1998 — The heavy mechanical general techniques and standards. Assembly
JB/T 5000.9-2007
$239.00