JB/T 5000.2-2007General technical requirements for heavy machinery - Part 2: Flame cut parts (English PDF)
重型机械通用技术条件 第2部分:火焰切割件
This is a limited preview
Buy now to download the full PDF (15 pages)
Need quotation for your management?
Get a formal quotation for JB/T 5000.2-2007 in 30 minutes.
Issued by
MIIT
Level / Type
Industry · Recommended
Issue date
August 28, 2007
Implementation date
February 1, 2008
Scope
JB/T 5000.2-2007 is the English-translated version of 重型机械通用技术条件 第2部分:火焰切割件.
JB/T 5000.2-2007 is the Chinese standard "General technical requirements for heavy machinery - Part 2: Flame cut parts". Its scope clause reads: The requirements of cutting surface quality of oxygen cutting workpiece, inspection requirements and cutting quality grade requirements are specified in this part of JB/T 5000.
This Part is applicable to the flame cutting of low carbon steel, medium carbon steel and common low alloy steel who are in thickness of 6mm ~300mm. Its clauses include terms and definitions.
Found what you need?
Document preview — JB/T 5000.2-2007
National Standard of the People's Republic of China
- Replacing
- JB/T 5000.2-1998
Issued by: Ministry of Industry and Information Technology of the People's Republic of China
Contents
- Contents
- Foreword
- 1 Scope
- 2 Normative References
- 3 Terms and Definitions
- 4 Quality Requirement of Flame Cutting Surface
- 5 Inspection Requirements
- 6 Inspection Method
- 7 Cutting Quality Grade
- 8 Marking Method
- Annex A (Informative)
- Cutting Allowance and Minimal Cutting Diameter
- Bibliography
- Table 1 The tolerance of verticality and tolerance of verticality of cut surface
- Table 2 Surface roughness of cut surface
- Table 3 Limit deviation of length dimension of cut surface
- Table 4 Limit deviation of groove angle and depth of cut surface
- Table 5 Surface defect requirements of cut surface
- Table 6 Shoulder melting degree requirements of cut surface
- Table 7 Adherent dross requirements of cut surface
- Table 8 Inspection range of verticality and gradient
- Table 9 Quantity requirements of inspected part
- Table 10 Cutting quality inspection
- Table 11 Requirements of cutting quality grade
- Table A.1 Slot width allowance
- Table A.2 Reserved machining allowance of cutting workpiece
- Table A.3 The minimum diameter flame cutting machine can cut is shown in Table A.3.
1 Scope
The requirements of cutting surface quality of oxygen cutting workpiece, inspection requirements and cutting quality grade requirements are specified in this part of JB/T 5000.
This Part is applicable to the flame cutting of low carbon steel, medium carbon steel and common low alloy steel who are in thickness of 6mm ~300mm.
2 Normative References
The following normative documents contain provisions which, through reference in this Part of JB/T 5000, constitute provisions of this Part. For dated reference, subsequent amendments to (excluding correction to), or revisions of, any of these publications do not apply. However, the parties whose enter into agreement according to this Part are encouraged to research whether the latest editions of these references are applied or not. For undated references, the latest edition of the normative document is applicable to this standard.
GB/T 985-1988 Basic Forms and Sizes of Weld Grooves for Gas Welding, Manual Arc Welding and Gas-shielded Arc Welding
GB/T 986-1988 Basic forms and sizes of submerged arc weld grooves
3 Terms and Definitions
The following terms and definitions are applicable to this Part.
3.1 Flame cutting
It refers to the method of using the thermal energy of gas flame to preheat the cutting part of workpiece to a certain temperature, and the high-speed cutting oxygen flow will spout to burn the workpiece and release heat to realize cutting. Flame cutting is also called gas cutting.
3.2 Tolerance of verticality
In this part, it refers to the tolerance of verticality of cutting surface profile line in the given section vertical to the base plane and the cutting length direction. The tolerance zone is the zone between two parallel straight lines which are vertical to the base plane and cutting length direction, and the distance between them is the tolerance value t, see Figure 1.
......
This preview omits tables, figures, formulas and parts of the technical clauses. The complete document — 15 pages — is available in the English PDF.
Referenced standards
Cited by
- GB/T 35981-2018Metallurgical equipment - Welding lugs - Technical specifications
- JB/T 13525-2018Gearboxes for hot rolling levellers
- JB/T 12228-2015Single/double-action horizontal aluminium extrusion presses
- JB/T 11897-2014Cone-type piercing mills
- JB/T 12047-2014Tubular closers with online pre-stretching for elevator steel wire ropes
- JB/T 5786-2014Cold pilger mills
Similar standards
Editions of JB/T 5000.2
| Edition | Title | Revision | Status |
|---|---|---|---|
| JB/T 5000.2-2007 | General technical requirements for heavy machinery - Part 2: Flame cut parts | current edition | Current |
| JB/T 5000.2-1998 | General technical requirements for heavy machinery - Part 2: Flame cut parts | previous edition | Superseded |
This page sells the current edition, JB/T 5000.2-2007. Earlier editions are listed for reference only.
How to Download JB/T 5000.2-2007
- 1
Add to cart
Click "Download PDF" on this page and choose "Buy this standard". You can add more standards before checkout.
- 2
Checkout
Enter your email and billing details. Payment is processed securely by Stripe (cards or bank transfer). Prefer bank details? Request a quotation (min. order $300).
- 3
Fast delivery
After payment you'll receive an email confirmation. The English PDF is sent to the same address, usually within minutes and at the latest within 1 business day.
- 4
Invoice included
A tax invoice is attached to the confirmation email. Need a custom invoice? Contact us.
Related Standards
JB/T 5000.3-2007 — General technical requirements for heavy machinery - Part 3: Weldments
JB/T 5000.1-1998 — The heavy mechanical general techniques and standards. Check of product
JB/T 5000.3-1998 — The heavy mechanical general techniques and standards. Welding
JB/T 5000.2-2007
$279.00