Valid

GB/T 14039-2002Hydraulic fluid power -- Fluids -- Method for coding the level of contamination by solid particles (English PDF)

Preview PDF

Also coversGBT14039-2002

This is a limited preview

Buy now to download the full PDF (13 pages)

Need quotation for your management?

Get a formal quotation for GB/T 14039-2002 in 30 minutes.

Issued by

General Administration of Quality Supervision, Inspection and Quarantine of PRC

Level / Type

National · Recommended

Issue date

October 11, 2002

Implementation date

May 1, 2003

Scope

GB/T 14039-2002 (Hydraulic fluid power -- Fluids -- Method for coding the level of contamination by solid particles) is available as an English-translated PDF.

GB/T 14039-2002 — This standard specifies the code used to determine the level of solid particle contamination in the fluid of hydraulic system.

Found what you need?

Document preview — GB/T 14039-2002

National Standard of the People's Republic of China

ICS: 23.100.60; 75.120

Issued by: General Administration of Quality Supervision, Inspection and Quarantine of PRC

Foreword...3
Introduction...5
1 Scope...6
2 Normative references...6
3 Description of code...6
4 Instructions on labeling (citing this standard)...10
Appendix A (Normative) Graphical representation of code...11
References...13

Foreword

This standard is modified to adopt ISO 4406:1999 "Hydraulic fluid power -

Fluids - Method for coding the level of contamination by solid particles" (English

version), which is a revision of GB/T 14039-1993 "Hydraulic fluid power - Fluids

- Method for coding the level of contamination by solid particles".

From the date of publication, this standard replaces GB/T 14039-1993.

This standard made the following revisions when adopting ISO 4406:1999:

- In "2 Normative references" and the corresponding references in the text,

USE GB/T 18854-2002 to replace "ISO 11171:1999" in ISO 4406:1999.

GB/T 18854-2002 revises and adopts ISO 11171:1999;

- In this standard, USE GB/T 14039-1993 to replace "ISO 4406:1987" as

mentioned in ISO 4406:1999. GB/T 14033-1193 equivalently adopts ISO

4406:1987;

- In the "References" of this standard, USE "GB/T 17489-1998" to replace

the "ISO 4021:1992" in ISO 4406:1999. GB/T 17489-1998 equivalently

adopts ISO 4021:1992.

- For ease of use, make the necessary editorial changes to ISO 4406:1999

in accordance with GB/T 1.1-2000.

The main modification contents of this standard to GB/T 14039-1993 are as

follows:

- For the use of automatic particle counter as calibrated according to GB/T

18854-2002, USE the particle concentration code of three size ranges: >= 4

µm (c), >= 6 µm (c), >= 14 µm (c) to indicate the contamination level of fluid;

- CANCEL the original code 0.9; ADD five codes: 25, 26, 27, 28, more than

28; INCREASE the total number of codes from 26 to 30;

- ADOPT the same standard name as the Chinese translation of ISO

4406:1999.

Appendix A of this standard is normative.

This standard was proposed by the China Machinery Industry Federation.

This standard shall be under the jurisdiction of the National Hydraulic and

Pneumatic Standardization Technical Committee (CSBTS/TC 3).

Drafting organizations of this standard: China University of Mining and

Hydraulic fluid power - Fluids - Method for coding the

level of contamination by solid particles

1 Scope

This standard specifies the code used to determine the level of solid particle

contamination in the fluid of hydraulic system.

2 Normative references

The provisions in following documents become the provisions of this Standard

through reference in this Standard. For the dated references, the subsequent

amendments (excluding corrections) or revisions do not apply to this Standard;

however, parties who reach an agreement based on this Standard are

encouraged to study if the latest versions of these documents are applicable.

For undated references, the latest edition of the referenced document applies.

GB/T 18854-2002 Hydraulic fluid power - Calibration of liquid automatic

particle counters (ISO 11177:1999, MOD)

ISO 4407:1991 Hydraulic fluid power - Fluid contamination - Determination

of particulate contamination by the counting method using a microscope

ISO 11500:1997 Hydraulic fluid power - Determination of particulate

contamination by automatic counting using the light extinction principle

3 Description of code

3.1 General

The purpose of the code is to convert the number of particles in a unit volume

of fluid into a wider range of grades or codes, to simplify the reporting of particle

count data. The code of contamination level for the fluid consists of the code.

For each level of code increased, the number of particles is typically doubled.

According to the original code of GB/T 14039-1993, the contamination level of

fluid is expressed by the particle concentration code of two size ranges of > 5

µm and > 15 µm. However, considering that the automatic particle counter uses

different calibration standards, the above particle size has been changed in this

standard. The report sizes after changing are 4 µm (c), 6 µm (c), 14 µm (c),

3.4.3 The second code is determined by the number of particles >= 6 µm (c).

3.4.4 The third code is determined by the number of particles >= 14 µm (c).

3.4.5 These three codes shall be written in order, separated by a slash.

For example: code 22/18/13, wherein the first code 22 indicates that the number

of particles >= 4 µm (c) per ml of fluid is between 20000 and 40000 (including

40000); the second code 18 indicates that number of particles >= 6 µm (c) per

ml is between 1330 and 2500 (including 2500); the third code 13 indicates that

the number of particles >= 14 µm (c) is between 40 and 80 (including 80).

3.4.6 When applying, it may use the two symbols "*" (indicating too many

particles to count) or "-" (indicating that it does not need to count) to represent

the code.

Example 1: */19/14 means that the number of particles >= 4 µm (c) in the fluid

is too many to count;

Example 2: -/19/14 indicates that the number of particles >= 4 µm (c) in the

fluid do not need to be counted.

3.4.7 When the original particle count value of one of the size ranges is less

than 20, the ">=" symbol shall be marked in front of the code of the size range.

For example: code 14/12/ >= 7 means that in each millimeter of fluid, the number

of particles >= 4 µm (c) is between 80 and 160 (including 160); the number of

particles >= 6 µm (c) is between 20 and 40 (including 40); the third code >= 7

means that the number of particles >= 14 µm (c) per millimeter of fluid is between

0.64 and 1.3 (including 1.3), but the count value is less than 20. At this time, the

credibility of the statistics is reduced. Due to the low level of confidence, the

code of the 14 µm (c) part may actually be higher than 7, which means that the

number of particles per millimeter of fluid may be greater than 1.3.

3.5 Determined of code by microscope count

3.5.1 It is counted according to ISO 4407.

3.5.2 The first code is determined by the number of particles >= 5 µm.

3.5.3 The second code is determined by the number of particles >= 15 µm.

3.5.4 In order to be consistent with the data report obtained by the automatic

particle counter, the code consists of three parts, wherein the first part is

denoted by the symbol "-".

For example: -/18/13.

......

......
This preview omits tables, figures, formulas and parts of the technical clauses. The complete document — 13 pages — is available in the English PDF.

Referenced standards

Normative references

GB/T 18854-2002 · ISO 11177 · ISO 4407 · ISO 11500

Cited by

How to Download GB/T 14039-2002

1
Add to cart
Click "Download PDF" on this page and choose "Buy this standard". You can add more standards before checkout.
2
Checkout
Enter your email and billing details. Payment is processed securely by Stripe (cards or bank transfer). Prefer bank details? Request a quotation (min. order $300).
3
Instant delivery (0–9 sec)
Delivery is automatic: within seconds of payment you'll receive an email with a secure download link. The link stays valid for 72 hours.
4
Invoice included
A tax invoice is attached to the confirmation email. Need a custom invoice? Contact us.