GB/T 3098.2-2015Mechanical properties of fasteners -- Nuts (English PDF)

Foreword

GB/T 3098 "Mechanical properties of fasteners" is composed of the following

parts.

- GB/T 3098.1 Mechanical properties of fasteners - Bolts, Screws and studs

- GB/T 3098.2 Mechanical properties of fasteners - Nuts;

- GB/T 3098.3 Mechanical properties of fasteners - Set screws;

- GB/T 3098.5 Mechanical properties of fasteners - Tapping screws;

- GB/T 3098.6 Mechanical properties of fasteners - stainless steel bolts,

screws and studs;

- GB/T 3098.7 Mechanical properties of fasteners - Thread rolling screws

- GB/T 3098.8 Mechanical properties of fasteners - Components for bolted

connections made mainly from materials with a high temperature strength;

- GB/T 3098.9 Mechanical properties of fasteners - Prevailing torque type

steel hexagon nuts;

- GB/T 3098.10 Mechanical properties of fasteners - Bolts, screws, studs,

and nuts made of non-ferrous metals;

- GB/T 3098.11 Mechanical properties of fasteners - Self-drilling tapping

screws;

- GB/T 3098.12 Mechanical properties of fasteners - Cone proof load test on

nuts;

- GB/T 3098.13 Mechanical properties of fasteners - Torsional test and

minimum torques for bolts and screws with nominal diameters 1mm to

10mm

- GB/T 3098.14 Mechanical properties of fasteners - Fasteners - Mechanical

properties - Widening test on nuts;

- GB/T 3098.15 Mechanical properties of fasteners - Nuts made of stainless

steel;

- GB/T 3098.16 Mechanical properties of fasteners - Stainless steel set

screws;

- GB/T 3098.17 Mechanical properties of fasteners - Preloading test for the

detection of hydrogen embrittlement - Parallel bearing surface method;

- GB/T 3098.18 Mechanical properties of fasteners - Blind rivets testing;

- GB/T 3098.19 Mechanical properties of fasteners - Blind rivets with break

pull mandrel;

- GB/T 3098.20 Mechanical properties of fasteners - Wing nuts with

specified proof torque;

- GB/T 3098.21 Mechanical properties of fasteners - Stainless steel tapping

screws;

- GB/T 3098.22 Mechanical properties of fasteners made of the fine grain

non-heat treatment steel - Bolts, screws and studs;

This part is part 2 of GB/T 3098.

This part was drafted in accordance with the rules given in GB/T 1.1-2009.

This part replaces GB/T 3098.2-2000 "Mechanical properties of fasteners -

Nuts - Coarse thread" and GB/T 3098.4-2000 "Mechanical properties of

fasteners - Nuts - Fine pitch thread".

As compared with GB/T 3098.2-2000 and GB/T 3098.4-2000, the main

changes of this part are as follows.

- COMBINE the two standards, MODIFY the standard name;

- ADD the examples for selection and application of low temperature and

high temperature steel, AND it may make reference to the contents of EN

10269, ASTM F 2281 and ASTM A 320/A 320M (SEE note 2 of Clause 1);

- SPEFICY the code used in this part (SEE Clause 3);

- SPECIFY the three types of nuts and their markings based on nut height

(SEE 4.1);

- ADD the design requirements for the bolt-nut connection (SEE Clause 5,

Appendix A);

- ADD that "when a thin nut is used as a lock nut, it shall be used together

with a regular nut or high nut. During installation, it shall firstly tighten the

thin nut on the assembly part, AND then tighten the regular nut or high nut

on the thin nut"; (SEE Clause 5);

- CANCEL the style 1 grade 4 coarse thread nuts (SEE Table 1 ~ Table 6);

- MAKE the following requirements for the coarse thread 04, 5, 6, 8 (style 2),

8 (style 1, D <= M16), and grade 9 AND the fine pitch thread 04, 5, 6 (D <=

M16) and grade 8 nuts "it may be quenched and tempered at the discretion

of the manufacturer"; (SEE footnote d of Table 3);

- ADD the requirements "it shall have sufficient hardenability" for the product

material requiring "quenching and tempering"; (SEE footnote e of Table 3);

- Not SPECIFY the proof stress, thread stress cross-sectional area, and the

thin nut failure load (SEE Table 7; Table 3, Table 5, Table 6 and Table 7 of

2000 version);

- ADD Brinell hardness and Rockwell hardness indicators (SEE Table 6,

Table 7);

- ADD the provisions that the manufacturer, supplier and purchaser may

choose their own method to test the quality of products (SEE Clause 8);

- ADD the requirements for testing machines and fixtures (SEE 9.1.3);

- ADD that "The sample shall be such nuts as passing the size inspections,

the GB/T 228.1 is referred, the separation rate of the test machine chuck

shall not exceed 3 mm/min, AND during the test, it shall limit the conditions

exceeding the proof load value at the minimum degree" (SEE 9.1.5);

- This part specifies that the minimum load for the Vickers hardness test is

98 N, and adds the Brinell hardness test load (SEE 9.2.3.1);

- In this part, USE the "Appendix A. Design principles of nuts" to replace the

"Appendix A. Bolt connection bearing capacity" of GB/T 3098.2-2000, and

ADJUST comprehensively the relevant content;

- In this part, "Failure mode of bolt-nut connection" does not contain

"looseness of nuts and screws" (SEE A.1; 3.1 of 2000 version);

- In this part, ADD the "Appendix B. Test mandrel thread size".

This part, through the re-drafting method, modifies and adopts the ISO

898-2.2012 "Mechanical properties of fasteners made of carbon steel and alloy

steel - Part 2.Nuts with specified property classes - Coarse thread and fine

pitch thread" (English version).

As compared with ISO 898-2.2012, the main changes are as follows.

- CHNAGE the standard name;

- In the reference documents, USE Chinese standards to replace

international standards (SEE Clause 2);

- ISO 898-2 makes reference to "ISO286-2 Geometrical product

specifications (GPS) - ISO code system for tolerances on linear sizes -

Part 2.Tables of standard tolerance grades and limit deviations for holes

and shafts" (SEE Clause 2);

- In ISO 898-2, it specifies that "These tests shall be carried out in the

manufacturing process or in the final inspection", which is in contradiction

with the provisions of 8.1 for the manufacturer's inspection, so it is not

adopted in this part (SEE Clause 7, 8.1);

- In ISO 898-2, it does not specify the basis for hardness conversion; in this

part, it specifies that if using the Brinell or Rockwell hardness test, it shall

conduct conversion in accordance with ISO 18265.2013 (SEE 9.2.2).

This part was proposed by the China Machinery Industry Federation.

This part shall be under the jurisdiction of the National Standardization

Technical Committee on Fasteners (SAC/TC 85).

The responsible drafting organization of this part. China Machine Productivity

Promotion Center.

This participating drafting organizations of this part. Haiyan Yuxing Nut Co.,

Ltd., Shanghai Shenguang High Strength Bolt Co., Ltd., Shanghai Jinma High

Strength Fastener Co., Ltd., Hebei Xinde Power Accessories Co., Ltd., Ningbo

Jiulong Fastener Manufacturing Co., Ltd. Shandong Gaoqiang Fasteners Co.,

Ltd., Zhejiang Huarui Standard Parts Co., Ltd., Jinyi Industrial Co., Ltd.,

Machinery Industry General Parts Product Quality Supervision and Testing

Center, Ningbo Mingli Fasteners Co., Ltd.

As for this part, the Secretariat of the National Standardization Technical

Committee for Fasteners is responsible for interpretation.

This part replaces the standard previously issued as follows.

- GB/T 3098.2-1982, GB/T 3098.2-2000.

- GB/T 3098.4-1986, GB/T 3098.4-2000.

Mechanical properties of fasteners - Nuts

1 Scope

This part of GB/T 3098 specifies the mechanical and physical properties of the

nuts with coarse thread and fine pitch thread made of carbon steel or alloy

steel when tested at ambient temperature range of 10 °C to 35 °C.

2 Normative references

The following documents are essential to the application of this document. For

the dated documents, only the versions with the dates indicated are applicable

to this document; for the undated documents, only the latest version (including

all the amendments) are applicable to this document.

3 Symbols

For the purposes of this document, the following symbols apply.

4 Designation systems

The marking and labelling of nuts with property classes shall be as specified in

Clause 10 for only those nuts which meet all applicable requirements of this

part.

The ranges of nominal diameters in relation to nut style and property class are

as given in Table 1.

5 Design of bolt and nut assemblies

Explanations of basic design principles of nuts and loadability of bolted

assemblies are given in Appendix A.

Thin nuts used as jam nuts shall be assembled together with a regular nut or

high nut.

6 Materials

Table 3 specifies the material and heat treatment for different property classes

of nuts.

7 Mechanical properties

When tested by the methods specified in Clause 9, the nuts of the specified

property class shall meet, at ambient temperature, the requirements for the

proof loads (SEE Table 4 and 5) AND for the hardness (SEE Table 6 and 7).

8 Inspection

The supplier tests the nuts which he provides using methods of their choice

(periodic evaluation of the manufacturer, checking of test results from the

manufacturers, physical tests on the nuts, etc), provided the mechanical and

physical properties specified in Table 3, 4, 5, 6 and 7 are met.

9 Test method

The tensile testing machine shall be in accordance with GB/T 16825.1, class 1

or better. Side thrust on the nut shall be avoided, e.g. by self-aligning grips.

......