HG/T 3696.1-2011Inorganic chemical products - Preparation of standard solutions, reagent solutions and products for chemical analysis - Part 1: Preparation of standard volumetric solutions (English PDF)
无机化工产品 化学分析用标准溶液、制剂及制品的制备 第1部分:标准滴定溶液的制备
This is a limited preview
Buy now to download the full PDF (45 pages)
Need quotation for your management?
Get a formal quotation for HG/T 3696.1-2011 in 30 minutes.
Issued by
MIIT
Level / Type
Industry · Recommended
Issue date
December 20, 2011
Implementation date
July 1, 2012
Scope
HG/T 3696.1-2011 is the English-translated version of 无机化工产品 化学分析用标准溶液、制剂及制品的制备 第1部分:标准滴定溶液的制备.
HG/T 3696.1-2011 is the Chinese standard "Inorganic chemicals for industrial use - Preparations of standard and reagent solutions for chemical analysis - Part 1: Preparations of standard volumetric solutions".
Its scope clause reads: This Part specifies the preparation and calibration methods of the main standard titration solutions, which are used by the volumetric method, for chemical analysis of inorganic chemical products.
This Part is applicable to the preparation of standard titration solutions of accurate concentration for volumetric determination of the main content and impurity content of inorganic chemical products.
It can also be used for chemical analysis of other chemical products. Its clauses include general provisions; warning; preparation and calibration of standard titration solution.
It was issued by the Ministry of Industry and Information Technology on DECEMBER 20, 2011 and took effect on JULY 01, 2012.
Found what you need?
Document preview — HG/T 3696.1-2011
National Standard of the People's Republic of China
- Replacing
- HG/T 3696.1-2002
Issued by: Ministry of Industry and Information Technology of the People's Republic of China
Contents
- Foreword
- 1 Scope
- 2 Normative references
- 3 General provisions
- 4 Warning
- 5 Preparation and calibration of standard titration solution
- 5.1 Sodium hydroxide standard titration solution
- 5.2 Hydrochloric acid standard titration solution
- 5.3 Sulfuric acid standard titration solution
- 5.4 Sodium carbonate standard titration solution
- 5.5 Potassium dichromate standard titration solution [c(1/6 K2Cr2) ~ 0.1 mol/L]
- 5.6 Sodium thiosulfate standard titration solution [c(Na2S2O3) ~ 0.1 mol/L]
- 5.7 Bromine standard titration solution [c(1/2Br2) ~ 0.1 mol/L]
- 5.8 Potassium bromate standard titration solution [c(1/6KBrO3) ~ 0.1 mol/L]
- 5.9 Iodine standard titration solution [c(1/2I2) ~ 0.1 mol/L]
- 5.10 Potassium carbonate standard titration solution
- 5.11 Oxalic acid standard titration solution [c(1/2C2H2O4) ~ 0.1 mol/L]
- 5.12 Potassium permanganate standard titration solution [c(1/5KMnO4) ~ 0.1 mol/L]
- 5.13 Ammonium ferrous sulfate standard titration solution {c[(NH4)2Fe(SO4)2] ~ 0.1 mol/L}
- 5.14 Cerium sulfate (or cerium ammonium sulfate) standard titration solution {c[Ce(SO4)2] ~ 0.1 mol/L, c[2(NH4)2(SO4) · Ce(SO4)2] ~ 0.1 mol/L}
- 5.15 Disodium ethylenediaminetetraacetate (EDTA) standard titration solution
- 5.16 Zinc chloride standard titration solution [c(ZnCl2) ~ 0.1 mol/L]
- 5.17 Magnesium chloride (or magnesium sulfate) standard titration solution [c(MgCl2) ~
- 0.1 mol/L, c(MgSO4) ~ 0.1 mol/L]
- 5.18 Lead nitrate standard titration solution {c[Pb(NO3)2] ~ 0.05 mol/L}
- 5.19 Copper sulfate standard titration solution [c(CuSO4) ~ 0.1 mol/L]
- 5.20 Silver nitrate standard titration solution [c(AgNO3) ~ 0.1 mol/L]
- 5.21 Sodium chloride standard titration solution [c(NaCl) ~ 0.1 mol/L]
- 5.22 Sodium thiocyanate (or potassium thiocyanate or ammonium thiocyanate) standard mol/L]
- 5.23 Sodium nitrite standard titration solution
- 5.24 Perchloric acid standard titration solution [c(HCIO4) ~ 0.1 mol/L]
- 5.25 Mercury nitrate standard titration solution {c[1/2Hg(NO3)2] ~ 0.1 mol/L}
- 5.26 Sodium oxalate standard titration solution
- Appendix A (Normative) Corrected value of volume of standard titration solution at different temperatures
- Appendix B (Informative) Determination of potentiometric titration end point and example of data recording
- Appendix C (Informative) Treatment method of mercury-containing waste liquid
1 Scope
This Part specifies the preparation and calibration methods of the main standard titration solutions, which are used by the volumetric method, for chemical analysis of inorganic chemical products.
This Part is applicable to the preparation of standard titration solutions of accurate concentration for volumetric determination of the main content and impurity content of inorganic chemical products. It can also be used for chemical analysis of other chemical products.
Issued on. DECEMBER 20, 2011 Implemented on. JULY 01, 2012 Issued by. Ministry of Industry and Information Technology of PRC
2 Normative references
The following documents are essential to the application of this document. For the dated documents, only the versions with the dates indicated are applicable to this document; for the undated documents, only the latest version (including all the amendments) is applicable to this standard.
GB/T 6682-2008 Water for analytical laboratory use - Specification and test methods
GB/T 8170 Rules of rounding off for numerical values & expression and judgement of limiting values
HG/T 3696.3-2011 Inorganic chemicals for industrial use - Preparations of standard and reagent solutions for chemical analysis - Part 3: Preparations of reagent solutions
3 General provisions
3.1 The water used in this Part, unless other requirements are specified, shall meet the specifications of grade-3 water in GB/T 6682-2008.
3.2 The reference reagents, which are used in the calibration in this Part, are the reference reagents for volumetric analysis; the other reagents used are all reagents of analytical grade or above.
3.3 Analytical balances, weights, burettes, volumetric flasks, single-marked pipettes, which are used in work, need to be calibrated regularly.
3.4 The concentration of the standard titration solution, which is prepared in this Part, except for perchloric acid, refers to the concentration at 20 °C. During calibration and use, if there is a difference in temperature, it shall be corrected, according to Appendix A.
4 Warning
Some of the reagents, which are used in the preparation method of this Part, are toxic or corrosive, so be careful when handling! If splashed on the skin, rinse immediately with water; in severe cases, seek medical attention immediately.
5 Preparation and calibration of standard titration solution
5.1 Sodium hydroxide standard titration solution
5.1.1 Preparation
5.2 Hydrochloric acid standard titration solution
5.2.1 Preparation
Pipette the specified volume of hydrochloric acid, according to Table 2. Pour it into 1000 mL of water. Shake well.
5.2.2 Calibration
5.2.2.1 Determination method
According to Table 2, weigh the specified amount of benchmark anhydrous sodium carbonate, which was calcined in a high temperature furnace at 270 °C ~ 300 °C to a constant mass, accurate to 0.0001 g.
5.2.2.2 Result calculation
The concentration of hydrochloric acid standard titration solution [c(HCl)] is expressed in moles per liter (mol/L), which is calculated according to formula (2).
5.5 Potassium dichromate standard titration solution [c(1/6 K2Cr2) ~ 0.1 mol/L]
5.5.1 Method 1
5.5.1.1 Preparation
Weigh 5 g of potassium dichromate. Dissolve it in 1000 mL of water. Shake well.
5.5.1.2 Calibration
5.7 Bromine standard titration solution [c(1/2Br2) ~ 0.1 mol/L]
5.7.1 Preparation
Weigh 3 g of potassium bromate and 25 g of potassium bromide. Dissolve it in 1000 mL of water. Shake well.
5.7.2 Calibration
5.14 Cerium sulfate (or cerium ammonium sulfate) standard titration solution {c[Ce(SO4)2] ~ 0.1 mol/L, c[2(NH4)2(SO4) · Ce(SO4)2] ~ 0.1 mol/L}
5.14.2 Calibration
5.14.2.1 Method 1
5.14.2.1.1 Determination method
Weigh 0.2 g of benchmark sodium oxalate, which is dried to the constant mass in an electric heating constant temperature drying oven at 105 °C ~ 110 °C, accurate to 0.0001 g. Dissolve it in 75 mL of water. Add 4 mL of sulfuric acid solution (20%) and 10 mL of hydrochloric acid. Heat it to 65 °C ~ 70 °C. Use the prepared cerium sulfate standard titration solution (or cerium ammonium sulfate) to titrate it, until the solution turns pale yellow. Add 3 drops of ferrous-o-phenanthroline indicator solution, to make the solution become orange-red. Continue to titrate, until the solution is light blue. At the same time, carry out a blank test. CHEMICAL INDUSTRY STANDARD OF THE PEOPLE'S REPUBLIC OF CHINA
ICS 71.060.01;71.060.99
G 10 Filing No.. 34581-2012 Replacing HG/T 3696.1-2002 Inorganic chemicals for industrial use - Preparation of standard and reagent solutions for chemical analysis - Part […]
......
This preview omits tables, figures, formulas and parts of the technical clauses. The complete document — 45 pages — is available in the English PDF.
Referenced standards
Normative references
- GB/T 6682-2008Water for analytical laboratory use - Specification and test methods
- GB/T 8170Rules of rounding off for numerical values & expression and judgement of limiting values
- HG/T 3696.3-2011Inorganic chemical products - Preparation of standard solutions, reagent solutions and products for chemical analysis - Part 3: Preparation of reagent solutions and products
Cited by
- GB/T 1587-2025Potassium carbonate for industrial use
- GB/T 1606-2025Sodium bicarbonate for industrial use
- GB/T 3051-2025General methods for the determination of chloride content in inorganic chemical products — Mercurimetric method and ion chromatography method
- GB/T 23850-2024Sodium perchlorate for industrial use
- GB/T 26521-2024Nickel carbonate for industrial use
- GB/T 1617-2023Barium chloride for industrial use
Similar standards
Editions of HG/T 3696.1
| Edition | Title | Revision | Status |
|---|---|---|---|
| HG/T 3696.1-2011 | Inorganic chemical products - Preparation of standard solutions, reagent solutions and products for chemical analysis - Part 1: Preparation of standard volumetric solutions | current edition | Current |
| HG/T 3696.1-2002 | Inorganic chemical products - Preparation of standard solutions, reagent solutions and products for chemical analysis - Part 1: Preparation of standard volumetric solutions | previous edition | Superseded |
This page sells the current edition, HG/T 3696.1-2011. Earlier editions are listed for reference only.
How to Download HG/T 3696.1-2011
- 1
Add to cart
Click "Download PDF" on this page and choose "Buy this standard". You can add more standards before checkout.
- 2
Checkout
Enter your email and billing details. Payment is processed securely by Stripe (cards or bank transfer). Prefer bank details? Request a quotation (min. order $300).
- 3
Fast delivery
After payment you'll receive an email confirmation. The English PDF is sent to the same address, usually within minutes and at the latest within 1 business day.
- 4
Invoice included
A tax invoice is attached to the confirmation email. Need a custom invoice? Contact us.
Related Standards
GB/T 6682-2008 — Water for analytical laboratory use - Specification and test methods
GB/T 8170-1987 — Rules for rounding off of numerical values
GB/T 8170-2008 — Rules of rounding off for numerical values & expression and judgement of limiting values
HG/T 3696.1-2011
$475.00