GB/T 15211-2013Security alarm equipment -- Environmental adaptability requirements and test methods (English PDF)

Foreword

This standard was drafted in accordance with GB/T 1.1-2009 given rules.

This standard replaces GB/T 15211-1994 "alarm system environmental testing", compared to the main changes are as follows.

--- Deleted the term "false alarms", "leakage alarm", "failed state" (see Chapter 3, 1994);

--- Remove the "General" (see Chapter 4, 1994);

--- Remove the "supply voltage variation test" (see 1994 edition 5.8);

--- Remove the "light scattering test" (see 1994 edition 5.9);

--- Remove the "air flow test" (see 1994 edition 5.11);

--- Remove the "random vibration" (see 1994 edition 5.5);

--- Remove the "random vibration" accelerated test (see 1994 Version 6.5.3);

--- Increasing the term "public assistance system" and "stationary equipment", "mobile devices," "portable device", "pre-treatment", "conditions Test "," Recovery "(see Chapter 3);

--- Added "environment class" (see Chapter 4);

--- To increase the "standard test conditions" (see Chapter 5);

--- Increased "tolerance range" (see Chapter 6);

--- Added "relevant product standards should contain information" (see Chapter 7);

--- Added "temperature test" (see Chapter 11);

--- Added "salt spray cycle durability test" (see Chapter 18);

--- Added "Low Pressure Test" (see Chapter 19);

--- Added "simulated solar radiation and temperature rise test (working)" (see Chapter 25);

--- Added "simulated solar radiation and surface aging test (durability)" (see Chapter 26);

--- Amend the foreword;

--- Modify the scope (see Chapter 1, Chapter 1 of the 1994 edition);

--- Modify the temperature test (working) severities (see 834, 1994 Edition 5.1.3.);

--- Modify the temperature test (durability) of the severities (see 934, 1994 Edition 6.1.3.);

--- Modify the low temperature test (working) severities (see 1034, 1994, version 5.2.3.);

--- Modified Damp heat test (working) severities (see 1234, 1994, version 5.6.3.);

--- Modified Damp heat test (durability) of the severities (see 1334, 1994 version 6.2.3.);

--- Modified alternating hot and humid test (working) severities (see 1434, 1994 version 5.7.3.);

--- Modified alternating hot and humid (durability) of the severities (see 1534, 1994 version 6.3.3.);

--- The "shell protection test" to "water test" and "dust test" and modify the severity (see 16.3.2,27.3.2,1994 in version 5.13.3);

--- Modified sulfur corrosion durability test severities (see 1734, 1994 version 6.6.3.);

--- Modify the impact test (working) severities (see 2034, 1994 version 5.6.3.);

--- Modified hammer test (working condition) (see Chapter 21, 1994 Version 5.10);

--- Modify the free drop test (working) severities (see 2234, 1994 version 5.12.3.);

--- Modified sine vibration test (working) severities (see 2334, 1994 version 5.4.3.);

--- Modified sine vibration test (durability) of the severities (see 24.3 4, 1994 version 6.4.3).

This standard uses redrafted law revision using IEC 62599-1:2010 "Part 1 Alarm System. Environmental test methods." this standard and IEC 62599-1:2010 compared to more adjustments in the structure, listed in Appendix A of this standard and IEC 62599-1.

Article 2010 of chapter numbering control list.

This standard and IEC 62599-1:2010 compared to the existence of technical differences, Appendix B gives the corresponding technical differences and their reasons for a Lanbiao.

This standard made the following editorial changes.

--- The standard name was changed to "environmental adaptability alarm equipment security requirements and test methods";

--- Remove the IEC 62599-1:2010 Foreword;

--- Increasing the foreword;

The term --- "IEC 62599-1 this part" to "this standard";

--- With a decimal point "." Instead of a comma as the decimal point "." Please note that some of the content of this document may involve patents. Release mechanism of the present document does not assume responsibility for the identification of these patents.

This standard by the National Security Alarm System Standardization Technical Committee (SAC/TC100) centralized.

This standard is mainly drafted by. Ministry of Public Security and Police Electronic Products Quality Inspection Center, Beijing in the security shield technology development company, the public Abe Security Alarm System Product Quality Supervision and Inspection Center, Honeywell (China) Co., Ltd., Shenzhen Security Technology Co., measurement standards the company.

1 Scope

This standard specifies the security alarm device environmental compatibility test purposes, test mode, test equipment and test procedures.

This standard applies to the following security alarm devices in the system.

a) intrusion alarm systems;

b) video surveillance system;

c) Access Control System (including the building intercom system, electronic patrol system, parking (library) safety management systems, etc.);

d) the public assistance system;

e) a remote receiver and/or monitoring center;

Combinations and/or integrated systems f) a) ~ e) of the subsystems;

g) containing solid protective equipment electronic device;

h) biometric identification applications.

2 Normative references

The following documents for the application of this document is essential. For dated references, only the dated version suitable for use herein Member. For undated references, the latest edition (including any amendments) applies to this document.

GB/T 2421.1-2008 Environmental testing for electric and electronic products - Part 1. General and guidance (IEC 60068-1. 1988, IDT) GB/T 2423.1 Environmental testing for electric and electronic products Part 2. Test methods Test A. Cold (GB/T 2423.1-2008, IEC 60068-2-1:2007, IDT) GB/T 2423.2 Environmental testing for electric and electronic products Part 2. Test methods Test B. Dry heat (GB/T 2423.2-2008, IEC 60068-2-2:2007, IDT) GB/T 2423.3 Environmental testing for electric and electronic products Part 2. Test methods - Test Cab. Damp heat method (GB/T 2423.3-2006,60068-2-78.2001, IDT) GB/T 2423.4 Environmental testing for electric and electronic products Part 2. Test methods - Test Db Damp (12h 12h cycle Ring) (GB/T 2423.4-2008, IEC 60068-2-30:2005, IDT) GB/T 2423.18 Environmental testing - Part 2. Test methods - Test Kb. Salt mist, cyclic (sodium chloride solution) (GB/T 2423.18-2012, IEC 60068-2-52:1996, IDT) GB/T 2423.21 Environmental testing for electric and electronic products Part 2. Test methods - Test M. Low air pressure (GB/T 2423.21-2008, IEC 60068-2-13. 1983, IDT) GB/T 2423.24-1995 Environmental testing for electric and electronic products Part 2. Test methods - Test Sa. too on the analogue terrestrial Solar radiation (IEC 60068-2-5. 1975, IDT) GB/T 2423.38 Environmental testing for electric and electronic products Part 2. Test methods Test R. Water test method and guidance (GB/T 2423.38-2008, IEC 60068-2-18:2000, IDT) GB/T 2423.55 Environmental testing for electric and electronic products Part 2. Environmental Test Test Eh. Hammer tests (GB/T 2423.55-2008, IEC 60068-2-75:1997, IDT) GB 4208-2008 housing protection (IP Code) (IEC 60529. 1989, IDT)