GB 10409-2001Burglary resistant safes (English PDF)

3.1 Burglary resistant safes

It refers to a kind of safes that is equipped with mechanical and electronic lock (including combination

lock, IC card lock, etc.) which can be used to resist abnormal entry under specified conditions within the

required time.

3.2 Safety class

The classification of anti-destruction capacity that the burglary resistant safes can withstand. The

classification is divided based on the duration of net working time that the burglary resistant safes can

resist to the abnormal entry, under the action of the specified destroying tools.

3.3 Entry

During the destruction resistant test, open the cabinet door of various burglary resistant safes or make

an opening not smaller than the specified area on the cabinet door or body, within the specified net

working time. Class A burglary resistant safes is 38cm2; Class B and Class C burglary resistant safes are

13cm2.

3.4 Common hand tools

Including the chisel, punch, wedge, screwdriver, hacksaw, wrench, pliers, hammer with the of weight not

more than 3.6kg, the prying tools with the length of not more than 1.5m, and general digging tools.

3.5 Portable electric tools

The electric hand drills with the bit diameter of not more than 12.5mm, the electric hammer drills with the

punch diameter of not more than 25mm and the pressure devices.

3.6 Grinding point

The grinding tools with shapes such as cone, disk, or cylinder that is driven by die grinders with the

rotate speed of 14000 r/min-22000 r/min.

The mechanical lock used in the burglary resistant safes shall comply with the requirements of GA/T 73.

5.4 Electronic lock (including IC card lock, electronic combination lock, etc.)

5.4.1 The coded number of the electronic combination lock shall not be less than 106.And the password

can be changed arbitrarily.

5.4.2 If the password is entered by key buttons, the key buttons shall not occur any failure in 6000

continuous pressing actions.

5.4.3 When the electronic combination lock are knocked by the energy of not more than 0.5J, the

mis-operation and damage phenomena shall be avoided.

5.4.4 The electronic combination lock shall have emergency opening function. And it may have multilevel

and multi-group opening passwords.

5.4.5 The password entrance of electronic combination lock shall be prompted. When it is continuously

entered with wrong password for three times or mis-operation, the electronic combination lock shall have

time-limited locking, alarm and other functions. However, after the time-limited locking and alarm, it shall

recover the correct operation and operate normally.

5.4.6 When the supply voltage of the electronic lock changes within the range of 85%-110% of the rated

voltage, the electronic lock shall be able to work normally. When the power voltage is below the specified

alarm voltage, it shall have under-voltage alarm indications. After under-voltage alarm, the power

capacity shall still meet more than 240 times of normal opening and closing of electronic lock.

5.4.7 The electronic lock shall be equipped with external power interface or emergency opening unit.

5.4.8 For the burglary resistant safes adopting electronic lock, the key parts of electronic lock shall be

protected. When the keyboard, wire, electromechanical actuators are destroyed and attacked, they shall

be able to withstand the destruction resistant test for corresponding classes of burglary resistant safes.

5.4.9 The environmental suitability of electronic lock shall comply with the requirements of A-1/2; A-2/5;

A-3/3; A-4/1; A-6/3; and A-18/3 in GB /T15211-1994.

5.4.10 The immunity requirements of the electronic lock shall meet the test requirements specified in

GB/T 17626.2 (Grade 1), GB/T 17626.3 (Grade 1), GB/T 17626.4 (Grade 1), GB/T 17626.5 (Grade 1)

and GB/T 17626.11 (Class 40, duration of 5 cycles).

5.5 Power supply

5.5.1 The power supply's power, energy consumption, environmental adaptability and safety

requirements shall satisfy the corresponding product technical requirements.

5.5.2 When the AC 220V power supply is used as the main power supply, there shall have a standby

power (a rechargeable battery or primary battery). It works normally within the range of 85%-110% of

rated voltage of the main power supply. And there shall have an overcurrent protecti...

......