GB/T 3859.1-2013Semiconductor converters -- General requirements and line commutated Converters -- Part 1-1: Specification of basic requirements (English PDF)

4.1.5 and 4.1.6 of this Edition; 4.1.2, 4.1.5 and 4.1.6 of 1993 Edition);

--- Add the "marking" of converter (see 4.2 of this Edition);

--- Modify the "basic parameters" of the converter (see 4.3 of this Edition; 4.2 of

6.2.2.1 and 6.2.3 of this Edition; 5.7.1.1 and 5.7.2 of 1993 Edition);

--- Add the voltage adjustment values of "12-pulse converter" and "Buck-boost

converter (series connection)" (see 6.2.4.5 and 6.2.4.6 of this Edition);

--- Modify "Grid-side voltage current harmonics" and "DC-side harmonics" (see 6.3.1

of this Edition; 5.7.4 and 5.7.5 of 1993 Edition);

--- Add "Commutation gap" and "Voltage fluctuation" (see 6.3.1 and 6.3.3 of this

Edition);

--- Modify "Harmonic interference" (see 6.3.4 of this Edition; 5.7.6 of 1993 Edition);

--- Add "Immunity" (see 6.3.5 of this Edition);

--- Modify "Rated value of converter", "Noise", "Current and voltage balance", and

"stability and requirements" (see 6.4~6.5, 6.6.1~6.6.7 of this Edition; 5.6,

5.7.9~5.7.11 of 1993 Edition);

--- Add "Safety Requirements" (see 6.6.8 of this Edition);

--- Modify the "General', "Inspection rules" and "Test items" of inspection and test

(see 7.1 of this Edition; 6.1~6.3 of 1993 Edition);

--- Modify "Insulation test", "Light load test", "rated current test", "Overload capability

test", "Inherent voltage adjustment rate measurement" and "Ripple

measurement" (see 7.2, 7.3.1~7.3.5 of this Edition; 6.4.1~6.4.3, 6.4.10, 6.4.8

and 6.4.17 of 1993 Edition);

--- Add "Harmonics current measurement" (see 7.3.6 of this Edition);

--- Modify "Temperature-rise test", "Auxiliary device test", "Control equipment

performance test", "Protection system test", "Cooling system test", "Immunity

test", "Radio frequency interference and conducted noise test", "Audio noise

measurement" and "Allowance difference" (see 7.4.2, 7.5~7.7 and 7.8 of this

Edition; 6.4.6, 6.4.11~6.4.16, 6.4.19.4 and Clause 7 of 1993 Edition);

--- Modify "Marking, Packaging, Transportation, Storage" (see Clause 8 of this

Edition; Clause 8 of 1993 Edition);

--- Delete "Model", "Components and auxiliary devices" and "Other properties" in

the technical performance (4.3, 5.7.12 and 5.7.13 of 1993 Edition);

--- Delete "Load test", "Balance measurement", "Stability device performance

inspection", "Component inspection", "Cabinet inspection", "Assembly

inspection", "Environmental condition test" and "Other tests" (6.4.4, 6.4.9, 6.4.18,

6.4.19.1~6.4.19.3, 6.4.20 and 6.4.21 of this Edition);

--- Add Annexes A, B and C.

This Part uses the re-drafting method to modify and adopt IEC 60146-1-1.2009

Semiconductor Converters - General Requirements and Line Commutated Converters

- Part 1-1.Specification of Basic Requirements.

Compared with IEC 60146-1-1.2009, this Part add 16 subclauses (4.1.6, 4.2.1~4.2.3,

4.3, 5.3.1.4~5.3.1.5, 6.3.1.5, 6.3.2~6.3.3, 6.3.5.3, 6.6, 7.5.4 and 8.2~8.4 of this Edition),

and 1 table (Table 19); adjust 4.2 into 3.12; adjust 4.3.1 into 5.1.1; adjust 4.3.2.1 into

5.1.2; adjust 4.3.2.2 into 5.1.3; adjust 4.3.3.1 into 5.2.1; adjust 4.3.3.2 into 5.2.2 and

5.2.3; adjust 5.1 into 4.2.4; adjust 5.2.1~5.2.3 into 5.3.1.1~5.3.1.3; adjust 5.2.4 into 5.4;

adjust 5.3 into 5.3.3; adjust 5.4.1 into 5.3.2.1 and 6.3.5; adjust 5.4.2 into 5.3.2.2; adjust

6.2.1 into 6.1.3 and 6.2.1; adjust 6.3.2 into 6.3.4; and adjust 6.6 into 8.1 in the structure.

Compared with IEC 60146-1-1.2009, this Part has the technical differences and

causes as follows.

--- According to the actual citation in the standard provisions, add some normative

references (see Clause 2 of this Part);

--- Add the term "Modular power supply" and its definition (see 3.1.22 of this Part);

--- Modify the classification method of converters (see 4.1 of this Part);

--- Add "Identification of electrical connection", "Identification of device terminals

and conductor terminals", "Conductor colour" and "Main technical parameters"

(see 4.2.1~4.2.3, 4.3 of this Part);

--- Modify the operating conditions of outdoor device [see 5.3.1.3c) of this Part];

--- Add "Elevation" and "Heat Transfer Medium" (see 5.3.1.4~5.3.1.5 of this Part);

--- Add "Harmonic suppression", "Commutation gap", "Voltage fluctuation", "Choice

of immunity level" and "Other performance" (see 6.3.1.5, 6.3.2~6.3.3, 6.3.5.3 and

6.6 of this Part);

--- Modified the "General" of the test (see 7.1 of this Part);

--- Add Table 19 "The Temperature-Rise Limit of Each Part of the Converter";

--- Modify "Auxiliary device inspection" and "Protection device inspection" (see 7.5.1

and 7.5.3 of this Part);

--- Add "Cooling device inspection", "Packaging", "Transportation" and "Storage"

(see 7.5.4 and 8.2~8.4 of this Part).

This Part was proposed by China Electrical Equipment Industry Association.

This Part shall be under the jurisdiction of National Technical Committee for

Standardization of Power Electronics (SAC/TC 60).

Drafting organizations of this Part. Xi'an Power Electronics Research Institute; Rongxin

Power Electronic Co., Ltd.; Xiamen Kehua Hengsheng Co., Ltd.; Guangdong Zhicheng

Champion Group Co., Ltd.; Chuangtong Science and Technology Development Co.,

Ltd., Qingdao Economic and Technology Development Zone; Wolong Electronic

Beijing Huatai Transformer Co., Ltd.; Beijing Newimage Electric Technology

Development Co., Ltd.; and Beijing AriTime Intelligent Control Co., Ltd.

Chief drafting staffs of this Part. Zhou Guanyong, Wei Hongqi, Zhang Fanyong, Chen

Chenghui, Li Minying, Sui Xueli, He Baozhen, Chen Sixiong, Luo Bendong, Yang

Yanqiu, and Hu Ying.

The historical edition replaced by this Standard is as follows.

--- GB 3859-1983, GB/T 3859.1-1993.

Semiconductor Converters - General Requirements

and Line Commutated Converters - Part 1-1.

Specification of Basic Requirements