GB/T 242-2007Metal materials -- Tube -- Drift-expending test (English PDF)
金属管 扩口试验方法
This is a limited preview
Buy now to download the full PDF (6 pages)
Need quotation for your management?
Get a formal quotation for GB/T 242-2007 in 30 minutes.
Issued by
General Administration of Quality Supervision, Inspection and Quarantine
Level / Type
National · Recommended
Issue date
July 18, 2007
Implementation date
February 1, 2008
Scope
GB/T 242-2007 is the English-translated version of 金属管 扩口试验方法.
GB/T 242-2007 — This Standard specifies a method for determining the ability of metallic tubes of circular cross- section to undergo plastic deformation in drift expansion.
This Standard is intended for tubes having an outside diameter no greater than 150 mm (100 mm for light metals) and a thickness no greater than 10 mm although the range of the outside diameter or the thickness for which this Standard is applicable may be more exactly specified in the relevant product standard.
Found what you need?
Document preview — GB/T 242-2007
National Standard of the People's Republic of China
- ICS
- 77.040.10
- Classification
- H 23
Issued by: General Administration of Quality Supervision, Inspection and Quarantine
Contents
- Foreword...3
- 1 Scope...4
- 2 Symbols, Designations and Units...4
- 3 Principle...5
- 4 Testing Equipment...5
- 5 Test Piece...5
- 6 Procedure...6
- 7 Test Report...6
Foreword
This Standard equivalently adopted ISO 8493:1998 (E) Metallic Materials – Tube – Drift-
Expanding Test.
This Standard equivalently translated ISO 8493:1998 (E) Metallic Materials – Tube – Drift-
Expanding Test.
This Standard made the following editorial modifications:
a) Change "this International Standard" into "this Standard";
b) Use decimal point "." to replace comma "," which is used as the decimal point;
c) Delete the Foreword of the international standard; and add the Foreword of this Standard;
d) Change the Clause 7 a) "Refer to this International Standard, e.g., ISO 8493" of the
original standard into "this Standard number";
e) Supplement the calculation formula of drift-expanding rate in the form of additional
information after Subclause 6.2 of Clause 6.
This Standard replaced GB/T 242-1997 Metallic Materials – Tube – Drift Expanding Test.
1) Supplement the Scope;
2) Reregulate the requirements for specimen;
3) Provide more detailed information on test procedures and test conditions.
This Standard was proposed by China Iron & Steel Association.
This Standard shall be under the jurisdiction of National Technical Committee on Steel of
Standardization Administration of China.
Drafting organizations of this Standard: Tianjin Pipe (Group) Corporation Limited; China
Metallurgical Information and Standardization Institute; and Pangang Group Chengdu Iron &
Steel Co., Ltd.
Chief drafting staffs of this Standard: Su Yingqun, Sun Yu, Dong Li, and Zhang Xinrong.
The historical editions replaced by this Standard are as follows:
--- GB 242-1963, GB 242-1982, GB/T 242-1997.
Metal Materials – Tube – Drift-Expanding Test
1 Scope
This Standard specifies a method for determining the ability of metallic tubes of circular cross-
section to undergo plastic deformation in drift expansion.
This Standard is intended for tubes having an outside diameter no greater than 150 mm (100
mm for light metals) and a thickness no greater than 10 mm although the range of the outside
diameter or the thickness for which this Standard is applicable may be more exactly specified
in the relevant product standard.
2 Symbols, Designations and Units
Symbols, designations and units for the drift-expanding test of tubes are given in Table 1 and
are shown in Figure 1.
......
......
This preview omits tables, figures, formulas and parts of the technical clauses. The complete document — 6 pages — is available in the English PDF.
Referenced standards
Cited by
- GB/T 15062-2025Wrought superalloy — Seamless tube
- GB/T 46219-2025Corrosion-resistant alloy U-bent tubes
- GB/T 46439-2025Seamless stainless steel pipes for hydrogen powered vehicle piping
- GB/T 44327-2024Welded zirconium and zirconium alloy tube and pipe
- GB/T 23609-2023Seamless copper alloy tube for water desalting applications
- GB/T 2882-2023Nickel and nickel alloy tubes
How to Download GB/T 242-2007
- 1
Add to cart
Click "Download PDF" on this page and choose "Buy this standard". You can add more standards before checkout.
- 2
Checkout
Enter your email and billing details. Payment is processed securely by Stripe (cards or bank transfer). Prefer bank details? Request a quotation (min. order $300).
- 3
Fast delivery
After payment you'll receive an email confirmation. The English PDF is sent to the same address, usually within minutes and at the latest within 1 business day.
- 4
Invoice included
A tax invoice is attached to the confirmation email. Need a custom invoice? Contact us.
Related Standards
GB/T 10003-2026 — Biaxially oriented polypropylene (BOPP) film
GB/T 10004-2026 — Plastic/Plastic laminated films and pouches for packaging
GB/T 10007-2026 — Rigid cellular plastics - Determination of shear properties
GB/T 242-2007
$69.00