GB/T 4588.4-2017Sectional specification for rigid multilayer printed boards (English PDF)
刚性多层印制板分规范
This is a limited preview
Buy now to download the full PDF (34 pages)
Need quotation for your management?
Get a formal quotation for GB/T 4588.4-2017 in 30 minutes.
Issued by
SAMR; SAC
Level / Type
National · Recommended
Issue date
July 31, 2017
Implementation date
February 1, 2018
Scope
GB/T 4588.4-2017 is the English-translated version of 刚性多层印制板分规范.
GB/T 4588.4-2017 is the Chinese standard "Sectional specification for rigid multilayer printed boards". Its scope clause reads: GB/T 4588 provisions of this part of rigid multilayer printed circuit board performance requirements, quality assurance requirements and delivery requirements.
This section applies to a rigid plated (with or without blind holes or buried holes) rigid multilayer (3 or more conductive layer) PCB, but does not apply to Aerospace and aviation with rigid plates. Its clauses include terms and definitions.
Found what you need?
Document preview — GB/T 4588.4-2017
National Standard of the People's Republic of China
- ICS
- 31.180
- Classification
- L 30
- Replacing
- GB/T 4588.4-1996
Issued by: State Administration for Market Regulation; Standardization Administration of the PRC
Contents
- Foreword
- 1 Scope
- 2 Normative references
- 3 Terms and definitions
- 4 application level
- 5 test methods and requirements
- 5.1 General
- 5.2 Priority
- 5.3 Materials
- 5.4 Design
- 5.5 Appearance and size
- 5.6 Structural Integrity
- 5.7 Chemical Properties
- 5.8 Physical Properties
- 5.9 Electrical Properties
- 5.10 Environmental Adaptability
- 5.11 Other requirements
- 6 Quality Assurance Regulations
- 6.1 General rules
- 6.2 test conditions
- 6.3 Capacity Approval
- 6.4 Identification and approval
- 6.5 Quality consistency test
- 7 Delivery Requirements
- Appendix A (Normative) Crack definition
- Appendix B (Normative) Copper coating tensile strength and elongation
1 Scope
GB/T 4588 provisions of this part of rigid multilayer printed circuit board performance requirements, quality assurance requirements and delivery requirements.
This section applies to a rigid plated (with or without blind holes or buried holes) rigid multilayer (3 or more conductive layer) PCB, but does not apply to
Aerospace and aviation with rigid plates.
2 Normative references
The following documents for the application of this document is essential. For dated references, only the dated version applies to this article
Pieces. For undated references, the latest edition (including all amendments) applies to this document.
Printed circuit terminology GB/T 2036
GB/T 4588.3 PCB design and use
Printed board test methods
GB/T 4725 Printed Circuit Copper-clad Epoxy Glass Cloth Laminate
GB/T 5230 electrolytic copper foil
General specification for printed boards
GJB360B -.2009 Test Methods for Electronic and Electrical Components
SJ/T 10309 PCB with solder mask
SJ/T 11050 multi-layer PCB with epoxy glass fiber cloth prepreg adhesive sheet
SJ20810 PCB dimensions and tolerances
SJ20828-2002 conformity identification with the test pattern and layout of the general plan
3 Terms and definitions
GB/T 2036 and defined by the following terms and definitions apply to this document.
3.1 Crack cracking
The coating layer and the coating layer are cracked or separated and extended to the surface of the bottom layer.
The drawings of the cracks are shown in Appendix A.
3.2 Rectangle pad intact area
80% of the center width of the pad is multiplied by 80% of the length.
3.3 Round pad intact area pristineareaofroundsurfacemountland
The center of the pad diameter, the pad diameter within 80% of the range.
3.4 Laminate evaluation zone
The area between adjacent heated zones in the laminate.
......
This preview omits tables, figures, formulas and parts of the technical clauses. The complete document — 34 pages — is available in the English PDF.
Referenced standards
Cited by
- GB/T 33772.3-2025Quality assessment systems - Part 3: Selection and use of sampling plans for printed board and laminate end-product and in-process auditing
- GB/T 46385.1-2025Optical circuit boards - Part 1: General
- GB/T 43799-2024Sectional specification for high density interconnect printed boards
- GB/T 24114.1-2022Elecrtical equipments of machines—Sewing machinery numerical control system—Part 1:General technical specification
- YC/T 10.14-2018Tobacco Machinery General Technical Conditions Part 14: Electrical Control Systems
- GB/T 17499-2017Microcomputer controller for household washing machine
Similar standards
Editions of GB/T 4588.4
| Edition | Title | Revision | Status |
|---|---|---|---|
| GB/T 4588.4-2017 | Sectional specification for rigid multilayer printed boards | current edition | Current |
| GB/T 4588.4-1996 | Sectional specification for rigid multilayer printed boards | previous edition | Superseded |
This page sells the current edition, GB/T 4588.4-2017. Earlier editions are listed for reference only.
How to Download GB/T 4588.4-2017
- 1
Add to cart
Click "Download PDF" on this page and choose "Buy this standard". You can add more standards before checkout.
- 2
Checkout
Enter your email and billing details. Payment is processed securely by Stripe (cards or bank transfer). Prefer bank details? Request a quotation (min. order $300).
- 3
Instant delivery (0–9 sec)
Delivery is automatic: within seconds of payment you'll receive an email with a secure download link. The link stays valid for 72 hours.
- 4
Invoice included
A tax invoice is attached to the confirmation email. Need a custom invoice? Contact us.
Related Standards
GB/T 4588.1-1996 — Sectional specification for single and double sided rigid printed board
GB/T 4588.10-1995 — Printed boards. Part 10: Specification for flex-rigid double-sided printed boards with through connections
GB/T 4588.12-2000 — Specification for mass lamination panels (semi-manufactured multilayer printed boards)
Secure payment via Stripe
Payments accepted
GB/T 4588.4-2017
$600.00