GB/T 3048.10-2007Test methods for electrical properties of electric cables and wires - Part 10: Spark test of extruded protective sheaths (English PDF)
电线电缆电性能试验方法 第10部分：挤出护套火花试验
This is a limited preview
Buy now to download the full PDF (15 pages)
Need quotation for your management?
Get a formal quotation for GB/T 3048.10-2007 in 30 minutes.
Issued by
SAMR; SAC
Level / Type
National · Recommended
Issue date
December 3, 2007
Implementation date
May 1, 2008
Scope
GB/T 3048.10-2007 is the English-translated version of 电线电缆电性能试验方法 第10部分：挤出护套火花试验.
GB/T 3048.10-2007 is the Chinese standard "Test methods for electrical properties of electric cables and wires - Part 10: Spark test of extruded protective sheaths".
Its scope clause reads: This part of GB/T 3048 specifies the terms and definitions, test apparatus, specimen preparation, test procedures, test results and evaluation, calibration of test apparatus and test records of spark test of extruded corrosion protective sheaths.
This part is applicable to the inspection of the tightness of a corrosion protective sheath that is extruded outside the metal sleeve or metal armor layer. This part shall be used in combination with GB/T 3048.1. Its clauses include terms and definitions.
Found what you need?
Document preview — GB/T 3048.10-2007
National Standard of the People's Republic of China
- ICS
- 29.060
- Classification
- K 13
- Replacing
- GB/T 3048.10-1994
Issued by: State Administration for Market Regulation; Standardization Administration of the PRC
Contents
- Foreword i
- 1 Scope
- 2 Normative references
- 3 Terms and definitions
- 4 Test apparatus
- 5 Specimen preparation
- 6 Test procedures
- 7 Test results and evaluation
- 8 Calibration of test apparatus
- 9 Test records
1 Scope
This part of GB/T 3048 specifies the terms and definitions, test apparatus, specimen preparation, test procedures, test results and evaluation, calibration of test apparatus and test records of spark test of extruded corrosion protective sheaths.
This part is applicable to the inspection of the tightness of a corrosion protective sheath that is extruded outside the metal sleeve or metal armor layer.
This part shall be used in combination with GB/T 3048.1.
2 Normative references
The following documents contain provisions which, through reference in this part of GB/T 3048, constitute provisions of this part. For dated references, subsequent amendments to (excluding correction to), or revisions of, any of these publications do not apply. However, parties to agreements based on this part are encouraged to investigate the possibility of applying the most recent editions of the normative documents indicated below. For undated references, the latest editions apply to this part.
GB/T 2900.10-2001 Electrotechnical vocabulary - Electric cables [idt IEC 60050(461):1984]
GB/T 3048.1 Test methods for electrical properties of electric cables and wires - Part 1: General
GB/T 3048.9-2007 Test methods for electrical properties of electric cables and wires - Part 9: Spark test of insulated cores
JB/T 4278.10 Verification procedure for test equipment of rubber plastic wire and cable - Part 10: Spark tester
3 Terms and definitions
For the purposes of this part of GB/T 3048, the terms and definitions specified in GB/T 2900.10-2001 apply.
......
This preview omits tables, figures, formulas and parts of the technical clauses. The complete document — 15 pages — is available in the English PDF.
Referenced standards
Cited by
- GB/T 28427-2026Cables for electrified railways - 27.5 kV single-phase AC power cables and cable accessories
- GB/T 17737.4-2025Coaxial communication cables - Part 4: Sectional specification for leaky cables
- GB/T 31840.1-2025Aluminium alloy power cables with extruded insulation for rated voltages from 1 kV up to 35 kV - Part 1: Cables for rated voltages of 1 kV and 3 kV
- GB/T 31840.2-2025Aluminium alloy power cables with extruded insulation for rated voltages from 1 kV up to 35 kV - Part 2: Cables for rated voltages from 6 kV up to 30 kV
- GB/T 31840.3-2025Aluminium alloy power cables with extruded insulation for rated voltages from 1 kV up to 35 kV - Part 3: Cables for rated voltage 35 kV
- NB/T 11129-2023Control cable for coal mine
Similar standards
Editions of GB/T 3048.10
| Edition | Title | Revision | Status |
|---|---|---|---|
| GB/T 3048.10-2007 | Test methods for electrical properties of electric cables and wires - Part 10: Spark test of extruded protective sheaths | current edition | Current |
| GB/T 3048.10-1994 | Test methods for electrical properties of electric cables and wires - Part 10: Spark test of extruded protective sheaths | previous edition | Superseded |
This page sells the current edition, GB/T 3048.10-2007. Earlier editions are listed for reference only.
How to Download GB/T 3048.10-2007
- 1
Add to cart
Click "Download PDF" on this page and choose "Buy this standard". You can add more standards before checkout.
- 2
Checkout
Enter your email and billing details. Payment is processed securely by Stripe (cards or bank transfer). Prefer bank details? Request a quotation (min. order $300).
- 3
Instant delivery (0–9 sec)
Delivery is automatic: within seconds of payment you'll receive an email with a secure download link. The link stays valid for 72 hours.
- 4
Invoice included
A tax invoice is attached to the confirmation email. Need a custom invoice? Contact us.
Related Standards
GB/T 3048.1-2007 — Test methods for electrical properties of electric cables and wires - Part 1: General
GB/T 3048.11-2025 — Test methods for electrical properties of electric cables and wires — Part 11: Test for dielectric dissipation factor
GB/T 3048.12-2025 — Test methods for electrical properties of electric cables and wires - Part 12: Partial discharge test
Secure payment via Stripe
Payments accepted
GB/T 3048.10-2007
$105.00