JB/T 5000.5-2007General technical requirements for heavy machinery - Part 5: Non-ferrous metal castings (English PDF)
重型机械通用技术条件 第5部分：有色金属铸件
This is a limited preview
Buy now to download the full PDF (15 pages)
Need quotation for your management?
Get a formal quotation for JB/T 5000.5-2007 in 30 minutes.
Issued by
MIIT
Level / Type
Industry · Recommended
Issue date
August 28, 2007
Implementation date
February 1, 2008
Scope
JB/T 5000.5-2007 is the English-translated version of 重型机械通用技术条件 第5部分：有色金属铸件.
JB/T 5000.5-2007 is the Chinese standard "General technical requirements for heavy machinery - Part 5: Non-ferrous metal castings". Its scope clause reads: This part of JB/T 5000 specifies the technical requirements, test methods, acceptance regulations, sign and certification of non ferrous casting.
This part is applicable to the copper alloy, aluminum alloy, and zinc alloy castings produced by the sand mold, metal mold and centrifugal casting methods. Its clauses include technical requirements.
Found what you need?
Document preview — JB/T 5000.5-2007
National Standard of the People's Republic of China
- Replacing
- JB/T 5000.5-1998
Issued by: Ministry of Industry and Information Technology of the People's Republic of China
Contents
- Contents
- Foreword i
- 1 Scope
- 2 Normative References
- 3 Technical Requirements
- 3.1 Chemical Composition and Mechanical Property
- 3.2 Dimensional Tolerance and Configuration of Tolerance Zone
- 3.3 Mismatch (Mismatching Mould)
- 3.4 Machining Allowance
- 3.5 Examples of Calculation for Size of Rough Casting (see Table 3)
- 3.6 Geometrical Shape, Dimension
- 3.7 Surface Quality Requirement
- 3.8 Finishing of Defect
- 4 Test Methods
- 5 Acceptance Rules
- 6 Marking and Package
- 6.1 Marking and Quantity Certificate
- 6.2 Package
1 Scope
This part of JB/T 5000 specifies the technical requirements, test methods, acceptance regulations, sign and certification of non ferrous casting.
This part is applicable to the copper alloy, aluminum alloy, and zinc alloy castings produced by the sand mold, metal mold and centrifugal casting methods.
2 Normative References
The provisions in following documents, through reference in this Part of JB/T 5000, constitute the articles of this Part. For dated reference, subsequent amendments to (excluding corrigenda), or revisions of, any of these publications do not apply. However, all parties coming to an agreement according to this standard are encouraged to study whether the latest edition of these documents is applicable. For undated references, the latest edition of the normative document is applicable to this part.
GB/T 228 "Metallic Materials-Tensile Testing at Ambient Temperature" (GB/T 228-2002, eqv ISO 6892: 1998)
GB/T231.1 Metallic materials - Brinell hardness test - Part 1: Test method GB/T 231.1-2002, eqv ISO 6506-1:1999(E)
GB/T 1173 Casting aluminum alloys (GB/T 1173-1995, neq. ASTM B26:1992)
GB/T 1175 "Casting Zinc Alloys"
GB/T 1176 "Specification for cast copper alloys" (GB/T 1176-1987, neq ISO 1338: 1977)
GB/T 6060.1 Roughness comparison specimens--Cast surfaces (GB/T 6060.1-1997, eqv ISO 2632-3:1979)
GB/T 6414 Castings--System of dimensional tolerances and machining allowances (GB/T 6414-1999, eqv ISO 8062:1994)
JB/T 5000.13 Heavy Mechanical General Techniques and Standards-Part 13: Packing
3 Technical Requirements
3.1 Chemical Composition and Mechanical Property
3.1.1
Chemical composition and mechanical property of aluminum alloy casting shall meet the requirements of GB/T 1173.
3.1.2
Chemical composition and mechanical property of zinc alloy casting shall meet the requirements of GB/T 1175.
3.1.3
Chemical composition and mechanical property of copper alloy casting shall meet the requirements of GB/T 1173.
3.1.3.1
For the copper alloy castings that bear heavy load and are used for key positions, such as worm gear, wheel rim, and screw box and those whose maximum size is more than 500mm, mechanical property shall be used as the key acceptance basis. Little deviation is permitted in the chemical composition and its value shall be 10% of upper and lower limits of percentage composition for each main component.
3.1.3.2
For various bushings, bearing bush as well as sliding plate type copper alloy casting that bear light loads, are used for general positions and the maximum size is not greater than 500mm, chemical composition or mechanical property both can be taken as the acceptance basis; if either of them is qualified, it can be considered as qualification; the other one is only used for reference but it must have data.
3.2 Dimensional Tolerance and Configuration of Tolerance Zone
3.2.1
Dimensional tolerance shall meet the requirements of GB/T 6414; common class code and tolerance see Table 1. The same casting shall select the same tolerance class and tolerance class shall be selected according to basic size of rough casting.
3.2.2
Dimensional tolerance zone for Castings shall be distributed symmetrically in relation To basic size of rough casting, namely half of tolerance shall be located above the basic size and other half shall be below the basic size (see Figure 1). If there is special requirement, tolerance zone also can be distributed asymmetrically but must be noted in drawing or specified in technological document.
......
This preview omits tables, figures, formulas and parts of the technical clauses. The complete document — 15 pages — is available in the English PDF.
Referenced standards
Cited by
- JB/T 13404-2018Bar rolling lines - Cold shears
- JB/T 13443-2018Deep chamber cone crushers
- JB/T 13521-2018Down coilers for hot strip mills - Technical requirements
- JB/T 12832-2016NC ship frame cold bending machines
- JB/T 12939-2016Tension levellers for strip
- JB/T 12943-2016Cold tandem rolling lines - Flying shears - General technical requirements
Similar standards
Editions of JB/T 5000.5
| Edition | Title | Revision | Status |
|---|---|---|---|
| JB/T 5000.5-2007 | General technical requirements for heavy machinery - Part 5: Non-ferrous metal castings | current edition | Current |
| JB/T 5000.5-1998 | General technical requirements for heavy machinery - Part 5: Non-ferrous metal castings | previous edition | Superseded |
This page sells the current edition, JB/T 5000.5-2007. Earlier editions are listed for reference only.
How to Download JB/T 5000.5-2007
- 1
Add to cart
Click "Download PDF" on this page and choose "Buy this standard". You can add more standards before checkout.
- 2
Checkout
Enter your email and billing details. Payment is processed securely by Stripe (cards or bank transfer). Prefer bank details? Request a quotation (min. order $300).
- 3
Instant delivery (0–9 sec)
Delivery is automatic: within seconds of payment you'll receive an email with a secure download link. The link stays valid for 72 hours.
- 4
Invoice included
A tax invoice is attached to the confirmation email. Need a custom invoice? Contact us.
Related Standards
JB/T 5000.6-2007 — General technical requirements for heavy machinery - Part 6: Steel castings
JB/T 5000.4-2007 — General technical requirements for heavy machinery - Part 4: Iron castings
JB/T 5000.7-2007 — General technical requirements for heavy machinery - Part 7: Repair welding of steel castings
Secure payment via Stripe
Payments accepted
JB/T 5000.5-2007
$239.00