GB/T 13540-2009Seismic qualification for high voltage switchgear and controlgear (English PDF)
高压开关设备和控制设备的抗震要求
This is a limited preview
Buy now to download the full PDF (16 pages)
Need quotation for your management?
Get a formal quotation for GB/T 13540-2009 in 30 minutes.
Issued by
Standardization Administration of China
Level / Type
National · Recommended
Issue date
November 30, 2009
Implementation date
April 1, 2010
Scope
GB/T 13540-2009 is the English-translated version of 高压开关设备和控制设备的抗震要求.
GB/T 13540-2009 — GB 1984, GB 1985, GB/T 2424.25, GB 3906, GB 7674, GB/T 11022, GB 17467 terms and definitions established Apply to this standard.
Found what you need?
Document preview — GB/T 13540-2009
National Standard of the People's Republic of China
- ICS
- 29.130.10
- Classification
- K 40
- Replacing
- GB/T 13540-1992
Issued by: Standardization Administration of China
Contents
- Introduction
- 1 Scope and purpose
- 2 Normative references
- 3 Terms and definitions
- 4 Seismic performance test requirements
- 4.1 General
- 4.2 Preliminary analysis of
- 5 Earthquake Level
- 2 6 experimental verification
- 6.1 Overview
- 6.2 Installation
- 6.3 External load
- 6.4 Measurement
- 6.5 Frequency Range
- 6.6 Test Acceleration
- 6.7 Test
- 7 Comprehensive validation testing and analysis
- 7.1 Overview
- 7.2 Vibration and performance data
- 7.3 Numerical analysis
- Evaluate the seismic performance of 8
- Combination 8.1 Stress
- Criterion 8.2 earthquake accredited test
- 8.3 Performance evaluation test results
- 8.4 Allowable stress
- 9 Document
- Seismic Performance Test Information 9.1
- 9.2 Test Report
- 9.3 Analysis Report
- Characteristics Appendix A (normative) sample of
- A. A low level of excitation
- A. 2 free vibration test
- Seismic performance and control equipment adequacy criterion switch Annex B (informative)
- B. 1 Overview
- B. 2 Recommended installation rules and practice
- Annex C (normative) Seismic Verification Report
Foreword
This revised standard adopts IEC 62271-2:2003 "high-voltage switchgear and control equipment Part 2. Rated voltage 72.5kV and to Seismic requirements on ", while referring to the IEC 62271-207:2007" high-voltage switchgear and control equipment Part 207. Rated voltage Seismic requirements than 52kV gas insulated switchgear equipment "and IEC 62271-300:2006" high-voltage switchgear and control provided Test methods are cited GB/T 2423.43, GB/T 2423.48 and GB/T 2424.25 the three standards, this standard does not make Repeat;
--- This standard is mainly used original product "fortification intensity of 8 degrees to 9 degrees strut porcelain high-voltage switchgear" extended to "the amount of Constant voltage 3.6kV and above all high-voltage switchgear and control equipment "(such as. high-voltage AC circuit breakers, high voltage AC isolation and earthing switches, 72.5kV and above gas-insulated metal-enclosed switchgear (GIS), 3.6kV ~ 40.5kV AC Metal-enclosed switchgear, HV/LV prefabricated substations, etc.);
--- Applicable seismic ground level from the original horizontal acceleration 3m/s2 (corresponding to the reference seismic intensity VIII ~ IX degree degrees) outward expansion Exhibition to 2m/s2,3m/s2,5m/s2 (corresponding to the reference seismic intensity were. IX degree of = range;
--- Standards adopted in response spectrum damping ratios of 2%, 5%, 10%, 20% and greater, and the original standard of 3%, 5%, 7%, 10%, 15%.
Appendix A of this standard is a normative appendix, Appendix B, Appendix C are informative appendices.
The standard proposed by China Electrical Equipment Industrial Association.
This standard by the national high-voltage switch equipment Standardization Technical Committee (SAC/TC65) centralized.
1 Scope and purpose
GB 1984, GB 1985, GB/T 2424.25, GB 3906, GB 7674, GB/T 11022, GB 17467 terms and definitions established Apply to this standard.
4 Seismic performance test requirements
4.1 General
Seismic performance test shall verify the switching and control equipment, the ability to withstand seismic stress.
......
This preview omits tables, figures, formulas and parts of the technical clauses. The complete document — 16 pages — is available in the English PDF.
Referenced standards
Cited by
- GB/T 28547-2023Selection and application recommendations of metal oxide surge arresters for a. c. systems
- GB/T 30547-2023Filter resistor for high voltage direct current (HVDC) transmission system
- GB/T 42558.1-2023Seismic techniques of electrical equipment in converter station on plateau—Part 1:Directives for seismic test and evaluation
- GB/T 42009-2022High voltage alternating-current circuit-breakers for filter banks
- GB/T 4787.1-2021Grading capacitors for high-voltage alternating current circuit-breakers - Part 1: General
- GB/T 7674-2020Gas-insulated metal-enclosed switchgear for rated voltages of 72.5kV and above
How to Download GB/T 13540-2009
- 1
Add to cart
Click "Download PDF" on this page and choose "Buy this standard". You can add more standards before checkout.
- 2
Checkout
Enter your email and billing details. Payment is processed securely by Stripe (cards or bank transfer). Prefer bank details? Request a quotation (min. order $300).
- 3
Instant delivery (0–9 sec)
Delivery is automatic: within seconds of payment you'll receive an email with a secure download link. The link stays valid for 72 hours.
- 4
Invoice included
A tax invoice is attached to the confirmation email. Need a custom invoice? Contact us.
Related Standards
GB/T 7463-2026 — Surface active agents - Determination of the power to disperse calcium soap - Acidimetric method (Modifled Schoenfeldt method)
GB/T 8336-2026 — Special threads gauges for gas cylinders
GB/T 48115-2026 — Technical requirements for GNSS radio occultation detection payload
Secure payment via Stripe
Payments accepted
GB/T 13540-2009
$245.00