JB/T 9214-2010Non-destructive testing - Test methods for evaluating performance characteristics of A-scan pulse-echo ultrasonic testing systems (English PDF)
无损检测 A型脉冲反射式超声检测系统工作性能测试方法
This is a limited preview
Buy now to download the full PDF (15 pages)
Need quotation for your management?
Get a formal quotation for JB/T 9214-2010 in 30 minutes.
Issued by
MIIT
Level / Type
Industry · Recommended
Issue date
February 11, 2010
Implementation date
July 1, 2010
Scope
JB/T 9214-2010 is the English-translated version of 无损检测 A型脉冲反射式超声检测系统工作性能测试方法.
JB/T 9214-2010 is the Chinese standard "Non-destructive testing - Test methods for evaluating performance characteristics of A-scan pulse-echo ultrasonic testing systems".
Its scope clause reads: This standard applies when evaluating performance characteristics of ultrasonic testing systems at test field. The ultrasonic testing systems refer to equipment used in the test, including A-scan pulse-echo ultrasonic tester, ultrasonic probe and high frequency cable connected therewith.
In the test, only standard block specified in this standard is used instead of any electronic instruments. This standard only specifies test method for evaluating performance characteristics of ultrasonic testing systems, but does not propose performance index or acceptance condition.
Where necessary, the supplier and the purchaser may make an antecedent negotiation and specify the minimum performance index which the ultrasonic testing systems shall reach when the product is accepted.
This standard is only applicable to manual testing but not to automatic ultrasonic testing. This standard is only applicable to the system including ordinary contact ultrasonic normal probe or angled probe but not to the systems including ultrasonic probes of other types (such as bicrystal type and water immersion type). Its clauses include terms and definitions.
Found what you need?
Document preview — JB/T 9214-2010
National Standard of the People's Republic of China
- ICS
- 19.100
- Replacing
- JB/T 9214-1999
Issued by: Ministry of Industry and Information Technology of the People's Republic of China
Contents
- Foreword i
- 1 Scope
- 2 Normative References
- 3 Terms and Definitions
- 4 Items under Test
- 5 Test Methods for Surplus Sensitivity of Normal Probe
- 6 Test Methods for Vertical Linearity of Normal Probe
- 7 Test Methods for Horizontal Linearity
- 8 Test Methods for Resolution of Normal Probe
- 9 Test Method for Dead Zone of Normal Probe
- 10 Test Methods for Point of Incidence of Angled Probe
- 11 Test Methods for Angle of Refraction or K Value of Angled Probe
- 12 Test Methods for Resolution of Angled Probe
- 13 Test Methods for Surplus Sensitivity of Angled Probe
- 14 Test Report
- Annex A (Normative) Standard Block
1 Scope
1.1
This standard applies when evaluating performance characteristics of ultrasonic testing systems at test field. The ultrasonic testing systems refer to equipment used in the test, including A-scan pulse-echo ultrasonic tester, ultrasonic probe and high frequency cable connected therewith. In the test, only standard block specified in this standard is used instead of any electronic instruments.
1.2
This standard only specifies test method for evaluating performance characteristics of ultrasonic testing systems, but does not propose performance index or acceptance condition. Where necessary, the supplier and the purchaser may make an antecedent negotiation and specify the minimum performance index which the ultrasonic testing systems shall reach when the product is accepted.
1.3
This standard is only applicable to manual testing but not to automatic ultrasonic testing.
1.4
This standard is only applicable to the system including ordinary contact ultrasonic normal probe or angled probe but not to the systems including ultrasonic probes of other types (such as bicrystal type and water immersion type).
2 Normative References
The following documents contain provisions which, through reference in this standard, constitute provisions of this standard. For dated references, subsequent amendments (excluding corrections) to, or revisions of, any of these publications do not apply. However, all parties coming to an agreement according to this standard are encouraged to study whether the latest edition of these documents is applicable. For undated references, the latest edition of the normative documents applies.
GB/T 12604.1 Non-destructive Testing—Terminology—Terms Used in Ultrasonic Testing (GB/T 12604.1-2005, ISO 5577: 2000, DT)
GB/T 19799.1-2005 Non-destructive Testing—Ultrasonic Testing—Calibration Block No.1 (ISO 2400: 1972, DT)
GB/T 20737 Non-destructive Testing—General Terms and Definitions (GB/T 20737-2006, ISO/TS 18173: 2005, IDT)
JB/T 8428-2006 Non-destructive Testing—Blocks for Ultrasonic Testing
3 Terms and Definitions
For the purpose of this standard, the terms and definitions given in GB/T 12604.1 and GB/T 20737 apply.
......
This preview omits tables, figures, formulas and parts of the technical clauses. The complete document — 15 pages — is available in the English PDF.
Referenced standards
Normative references
- GB/T 12604.1Non-destructive testing - Terminology - Ultrasonic testing
- GB/T 19799.1-2005Non-destructive testing - Ultrasonic testing block - Part 1: Standard block No.1
- GB/T 20737Non-destructive testing -- General terms and definitions
- JB/T 8428-2006Non-destructive testing - General specification for ultrasonic blocks
Cited by
- NB/T 11517-2024Nondestructive inspection methods and criterions for important load-bearing components of mining hoisting conveyance
- NB/T 20003.2-2021Non-destructive testing for mechanical components in nuclear island of nuclear power plants - Part 2: Ultrasonic testing
- NB/T 47013.15-2021Nondestructive testing of pressure equipments - Part 15: Phased-array ultrasonic testing
- JB/T 9219-2016Spheroidal graphite cast iron - Test method for ultrasonic sound velocity
- JB/T 10554.1-2015Non-destructive testing - Ultrasonic testing of ductile iron shafts - Part 1: General principles
- JB/T 10659-2015Non-destructive testing - Ultrasonic testing of forged steel materials - Testing of connecting rods
Similar standards
Editions of JB/T 9214
| Edition | Title | Revision | Status |
|---|---|---|---|
| JB/T 9214-2010 | Non-destructive testing - Test methods for evaluating performance characteristics of A-scan pulse-echo ultrasonic testing systems | current edition | Current |
| JB/T 9214-1999 | Non-destructive testing - Test methods for evaluating performance characteristics of A-scan pulse-echo ultrasonic testing systems | previous edition | Superseded |
This page sells the current edition, JB/T 9214-2010. Earlier editions are listed for reference only.
How to Download JB/T 9214-2010
- 1
Add to cart
Click "Download PDF" on this page and choose "Buy this standard". You can add more standards before checkout.
- 2
Checkout
Enter your email and billing details. Payment is processed securely by Stripe (cards or bank transfer). Prefer bank details? Request a quotation (min. order $300).
- 3
Instant delivery (0–9 sec)
Delivery is automatic: within seconds of payment you'll receive an email with a secure download link. The link stays valid for 72 hours.
- 4
Invoice included
A tax invoice is attached to the confirmation email. Need a custom invoice? Contact us.
Related Standards
GB/T 12604.1-2020 — Non-destructive testing - Terminology - Ultrasonic testing
GB/T 20737-2006 — Non-destructive testing -- General terms and definitions
JB/T 8428-2006 — Non-destructive testing - Test blocks for ultrasonic testing
Secure payment via Stripe
Payments accepted
JB/T 9214-2010
$85.00