GB/T 4458.3-2013Mechanical drawings—Axonometric drawings (English PDF)
机械制图 轴测图
This is a limited preview
Buy now to download the full PDF (17 pages)
Need quotation for your management?
Get a formal quotation for GB/T 4458.3-2013 in 30 minutes.
Issued by
SAMR; SAC
Level / Type
National · Recommended
Issue date
December 17, 2013
Implementation date
October 1, 2014
Scope
GB/T 4458.3-2013 is the English-translated version of 机械制图 轴测图.
GB/T 4458.3-2013 is the Chinese standard "Mechanical drawings—Axonometric drawings". Its scope clause reads: GB/T 4458 This section specifies the method of drawing an isometric view of the three commonly used.
This section applies to hand-drawn and computer isometric view; also applies to the three-dimensional model projection drawing. Its clauses include terms and definitions; general provisions.
Found what you need?
Document preview — GB/T 4458.3-2013
National Standard of the People's Republic of China
- ICS
- 01.100.20
- Classification
- J 04
- Replacing
- GB/T 4458.3-1984
Issued by: State Administration for Market Regulation; Standardization Administration of the PRC
Contents
- Introduction
- 1 Scope
- 2 Normative references
- 3 Terms and definitions
- 4 1 General Provisions
- 5 painting
- 6 Dimensioning
- 7 piping system isometric view of the representation
- Appendix A (informative) isometric exploded view
1 Scope
GB/T 4458 This section specifies the method of drawing an isometric view of the three commonly used.
This section applies to hand-drawn and computer isometric view; also applies to the three-dimensional model projection drawing.
2 Normative references
The following documents for the application of this document is essential. For dated references, only the dated version suitable for use herein
Member. For undated references, the latest edition (including any amendments) applies to this document.
GB/T 4457.4 Mechanical drawings Fatou line
Graphics Graphical symbols line GB/T 6567.5 Technical drawings of piping systems, fittings and valves symbol isometric drawing method
GB/T 14692 Technical drawings - Projection Method
GB/T 16948 Technical product documentation - Vocabulary term projection
GB/T 26099.4 three-dimensional modeling of mechanical products General Rules Part 4. The model projection drawing
3 Terms and Definitions
The following terms and definitions apply to this document.
3.1 Isometric view axonometricdrawings
The object together with its reference to a Cartesian coordinate system, a direction not parallel to any coordinate plane direction, with parallel projection method to cast a single vote
Movies surface of the resulting graph.
3.2 Shaft angle axesangle
Isometric view of the angle between the two isometric axes.
3.3 Axial stretching coefficient
The ratio of the length unit a unit length corresponding axonometric projection axis of the shaft. OX, stretching coefficient OY, OZ axis respectively p, q and r are simplified representations.
4 General Provisions
4.1
isometric drawings can theoretically infinite variety, but the simple mapping and other factors to consider, generally use the following three kinds.
4.1.1
isometric view of Acronym isometric (Figure 1).
......
This preview omits tables, figures, formulas and parts of the technical clauses. The complete document — 17 pages — is available in the English PDF.
Referenced standards
Cited by
- GB/T 40121-2021Technical product documentation—Representation of product residual stress symbol
- JB/T 4015.1-2013Adaptable units for general use of wire and cable machinery - Pay-off and take-up - Part 1: General requirements
- JB/T 4032.1-2013Adaptable units for general use of wire and cable machinery - Haul-off - Part 1: General requirements
- GB/T 12212-2012Technical drawings - Dimensions,proportions and simplified representation for welding symbols
- JB/T 10904.1-2008Cabling machines for wires and cables - Technical requirements - Part 1: General
- JB/T 5813-2008Enamelling machines for winding wires - Technical requirements
Similar standards
Editions of GB/T 4458.3
| Edition | Title | Revision | Status |
|---|---|---|---|
| GB/T 4458.3-2013 | Mechanical drawings—Axonometric drawings | current edition | Current |
| GB/T 4458.3-1984 | Mechanical drawings—Axonometric drawings | previous edition | Superseded |
This page sells the current edition, GB/T 4458.3-2013. Earlier editions are listed for reference only.
How to Download GB/T 4458.3-2013
- 1
Add to cart
Click "Download PDF" on this page and choose "Buy this standard". You can add more standards before checkout.
- 2
Checkout
Enter your email and billing details. Payment is processed securely by Stripe (cards or bank transfer). Prefer bank details? Request a quotation (min. order $300).
- 3
Instant delivery (0–9 sec)
Delivery is automatic: within seconds of payment you'll receive an email with a secure download link. The link stays valid for 72 hours.
- 4
Invoice included
A tax invoice is attached to the confirmation email. Need a custom invoice? Contact us.
Related Standards
GB/T 4458.1-2002 — Mechanical drawings -- General principles of presentation -- Views
GB/T 4458.2-2003 — Mechanical drawings--Item references and its arrangement for assembling drawings
GB/T 4458.4-2003 — Mechanical drawings--Dimensioning
Secure payment via Stripe
Payments accepted
GB/T 4458.3-2013
$295.00