GB/T 36956-2018Testing of voltage sourced converter valve base control unit for high-voltage direct current power transmission using voltage sourced converters (English PDF)
柔性直流输电用电压源换流器阀基控制设备试验
This is a limited preview
Buy now to download the full PDF (20 pages)
Need quotation for your management?
Get a formal quotation for GB/T 36956-2018 in 30 minutes.
Issued by
SAMR; SAC
Level / Type
National · Recommended
Issue date
December 28, 2018
Implementation date
July 1, 2019
Scope
GB/T 36956-2018 is the English-translated version of 柔性直流输电用电压源换流器阀基控制设备试验.
GB/T 36956-2018 sets out how to test the valve base control equipment of voltage sourced converters used in flexible HVDC transmission.
It gives the requirements for the test sample, covering basic, functional, performance and interface requirements, and then the four stages of testing: type tests (electromagnetic compatibility, environmental, mechanical and insulation tests), factory tests, joint tests and on-site handover tests.
The joint tests include communication, start-up and outage tests, sub-module capacitor voltage balancing, circulating current suppression, duty system switching, sub-module fault protection, valve fault and leakage detection, power supply reliability and long-term stable operation.
It applies to the valve base control equipment of modular multilevel converters. It was issued on 28 December 2018 and has applied since 1 July 2019.
Found what you need?
Document preview — GB/T 36956-2018
National Standard of the People's Republic of China
- ICS
- 29.200
- Classification
- K 46
Issued by: State Administration for Market Regulation; Standardization Administration of the PRC
Contents
- Foreword
- 1 Scope
- 2 Normative references
- 3 Terms and Definitions
- 4 test sample (test sample) requirement
- 4.1 Basic requirements
- 4.2 Functional Requirements
- 4.3 Performance Requirements
- 4.4 Interface Requirements
- 5 type test
- 5.1 Electromagnetic Compatibility Test
- 5.2 Environmental Test
- 5.3 Mechanical performance test
- 5.4 Insulation performance test
- 6 Factory test
- 6.1 Overview
- 6.2 Appearance inspection
- 6.3 Power-on test
- 6.4 Environmental Test
- 6.5 Insulation test
- 7 joint test
- 7.1 Overview
- 7.2 Overall power-on test
- 7.3 Communication test
- 7.4 Startup test
- 7.5 Outage test
- 7.6 Sub-module capacitor voltage balance control test
- 7.7 Circulation suppression test
- 7.8 Response duty system switching test
- 7.9 Submodule Failure and Protection Test
- 7.10 Valve base control equipment detection valve failure protection test
- 7.11 Valve base control equipment detection valve leakage fault test
- 7.12 Valve-based control equipment power supply reliability test
- 7.13 Long-term stable operation test of valve-based control equipment
- 8 On-site handover test
- 8.1 Overview
- 8.2 Visual inspection
- 8.3 wiring check
- 8.4 Power Check
- Reference
Foreword
This standard was drafted in accordance with the rules given in GB/T 1.1-2009.
1 Scope
This standard specifies the type test of the voltage source converter valve base control equipment (hereinafter referred to as valve base control equipment) for flexible DC transmission.
Test requirements and methods related to factory test, joint test and on-site handover test.
This standard applies to modular multi-level converter valve-based control equipment.
2 Normative references
The following documents are indispensable for the application of this document. For dated references, only dated versions apply to this document. For undated references, the latest edition (including all amendments) applies to this document.
GB/T 2423.1-2008 Environmental testing of electric and electronic products - Part 2: Test methods Test A. Low temperature
GB/T 2423.2-2008 Environmental testing of electrical and electronic products - Part 2: Test methods Test B. High temperature
GB/T 2423.4-2008 Environmental testing of electrical and electronic products - Part 2: Test methods Test Db. alternating heat (12h) 12h cycle)
GB/T 2423.5-1995 Environmental testing for electric and electronic products - Part 2: Test methods Test Ea and guide. Impact
GB/T 2423.6-1995 Environmental testing for electric and electronic products - Part 2: Test methods Test Eb and guide. Collision
GB/T 2423.10-2008 Environmental testing of electric and electronic products - Part 2: Test method test Fc. Vibration (sinusoidal)
GB/T 2423.22-2012 Environmental testing - Part 2: Test methods Test N. Temperature change
GB/T 2887-2011 General specification for electronic computer venues
GB/T 7261-2016 Basic test method for relay protection and safety automatic devices
GB/T 9361-2011 Computer Site Safety Requirements
Electrical relays - Part 5: Insulation coordination requirements and tests for measuring relays and protective devices
GB/T 17626.2-2006 Electromagnetic compatibility test and measurement technology Electrostatic discharge immunity test
GB/T 17626.3-2016 Electromagnetic compatibility test and measurement technology RF electromagnetic field radiation immunity test
GB/T 17626.4-2018 Electromagnetic compatibility test and measurement technology Electrical fast transient burst immunity test
GB/T 17626.5-2008 Electromagnetic compatibility test and measurement technology Surge (impact) immunity test
GB/T 17626.6-2017 Electromagnetic compatibility test and measurement technology Conducted disturbance immunity of RF field induction
GB/T 17626.8-2006 Electromagnetic compatibility test and measurement technology Power frequency magnetic field immunity test
GB/T 17626.9-2011 Electromagnetic compatibility test and measurement technology Pulse magnetic field immunity test
GB/T 17626.10-2017 Electromagnetic compatibility test and measurement technique Damping oscillating magnetic field immunity test
GB/T 17626.12-2013 Electromagnetic compatibility test and measurement technology ringing wave immunity test
GB/T 17626.29-2006 Electromagnetic compatibility test and measurement technology DC power input port voltage dip, short interruption and Immunity test for voltage changes
GB/T 30553-2014 High-voltage direct current transmission based on voltage source converter
GB/T 34118-2017 Voltage source converter terminology for high voltage DC systems
......
This preview omits tables, figures, formulas and parts of the technical clauses. The complete document — 20 pages — is available in the English PDF.
Referenced standards
Normative references
- GB/T 2423.1-2008Environmental testing for electric and electronic products - Part 2: Test methods - Tests A: Cold
- GB/T 2423.2-2008Environmental testing for electric and electronic products - Part 2: Test methods - Tests B: Dry heat
- GB/T 2423.4-2008Environmental testing for electric and electronic products - Part 2: Test method - Test Db: Damp heat, cyclic (12 h + 12 h cycle)
- GB/T 2423.5-1995Environmental testing - Part 2: Test methods - Test Ea and guidance: Shock
- GB/T 2423.6-1995Environmental testing for electric and electronic products - Part 2: Test methods - Test Eb and guidance: Bump
- GB/T 2423.10-2008Environmental testing - Part 2: Test methods - Test Fc: Vibration (sinusoidal)
Similar standards
How to Download GB/T 36956-2018
- 1
Add to cart
Click "Download PDF" on this page and choose "Buy this standard". You can add more standards before checkout.
- 2
Checkout
Enter your email and billing details. Payment is processed securely by Stripe (cards or bank transfer). Prefer bank details? Request a quotation (min. order $300).
- 3
Instant delivery (0–9 sec)
Delivery is automatic: within seconds of payment you'll receive an email with a secure download link. The link stays valid for 72 hours.
- 4
Invoice included
A tax invoice is attached to the confirmation email. Need a custom invoice? Contact us.
Related Standards
GB/T 17626.10-2017 — Electromagnetic compatibility -- Testing and measurement techniques -- Damped oscillatory magnetic field immunity test
GB/T 17626.29-2006 — Electromagnetic compatibility (EMC) - Testing and measurement techniques - Voltage dips short interruptions and voltage variations on d.c. input power port immunity tests
GB/T 17626.4-2018 — Electromagnetic compatibility -- Testing and measurement techniques -- Electrical fast transient/burst immunity test
Secure payment via Stripe
Payments accepted
GB/T 36956-2018
$385.00