GB/T 26610.1-2022Guideline for implementation of risk-based inspection of pressure equipment system—Part 1: Basic requirements and implementation procedure (English PDF)
承压设备系统基于风险的检验实施导则 第1部分：基本要求和实施程序
This is a limited preview
Buy now to download the full PDF (29 pages)
Need quotation for your management?
Get a formal quotation for GB/T 26610.1-2022 in 30 minutes.
Issued by
SAMR; SAC
Level / Type
National · Recommended
Issue date
July 11, 2022
Implementation date
February 1, 2023
Scope
GB/T 26610.1-2022 is the English-translated version of 承压设备系统基于风险的检验实施导则 第1部分：基本要求和实施程序.
GB/T 26610.1-2022 is the Chinese standard "Guideline for implementation of risk-based inspection of pressure equipment system—Part 1: Basic requirements and implementation procedure".
Its scope clause reads: This document specifies the basic requirements and implementation procedures for the implementation of risk-based inspection (RBI) projects for pressure equipment systems.
The basic requirements and implementation procedures specified in this document are applicable to RBI projects implemented by pressure equipment systems in petrochemical plants, other industrial The RBI project implemented by the pressure equipment system can also be used for reference.
This document applies to RBI projects implemented by the following equipment and related components in the pressure equipment system. a) pressure vessel and all its pressure-bearing parts; b) Pressure piping and all pressure-bearing piping components within and within the boundaries of the process plant; c) atmospheric storage tanks; d) the casing under internal pressure in the moving equipment; e) Pressure-bearing parts in boilers and heating furnaces; f) Safety relief devices such as safety valves.
This document does not apply to the following equipment and related components in the pressure equipment system. a) instrumentation and control equipment; b) electrical equipment; c) buildings and structures; d) Mechanical parts other than pump casings and compressor casings in pumps and compressors. Its clauses include terms and definitions.
Found what you need?
Document preview — GB/T 26610.1-2022
National Standard of the People's Republic of China
- ICS
- 23.020.30
- Classification
- J 74
- Replacing
- GB/T 26610.1-2011
Issued by: State Administration for Market Regulation; Standardization Administration of the PRC
Contents
- Preface
- Introduction
- 1 Scope
- 2 Normative references
- 3 Terms and Definitions
- 4 Abbreviations
- 5 General
- 6 RBI Implementation Plan
- 7 RBI Assessment Data Collection
- 8 Identification of damage categories and failure modes
- 9 Failure Likelihood Assessment
- 10 Failure Consequences Assessment
- 11 Risk Identification, Evaluation and Management
- 12 Risk management through inspection
- 13 Other risk mitigation measures
- 14 Reassessment and update of RBI assessment results
- 15 Tasks, Responsibilities, Training and Competencies
- 16 Preservation of RBI documents and records
1 Scope
1.1
This document specifies the basic requirements and implementation procedures for the implementation of risk-based inspection (RBI) projects for pressure equipment systems.
1.2
The basic requirements and implementation procedures specified in this document are applicable to RBI projects implemented by pressure equipment systems in petrochemical plants, other industrial
The RBI project implemented by the pressure equipment system can also be used for reference.
1.3
This document applies to RBI projects implemented by the following equipment and related components in the pressure equipment system.
a) pressure vessel and all its pressure-bearing parts;
b) Pressure piping and all pressure-bearing piping components within and within the boundaries of the process plant;
c) atmospheric storage tanks;
d) the casing under internal pressure in the moving equipment;
e) Pressure-bearing parts in boilers and heating furnaces;
f) Safety relief devices such as safety valves.
1.4
This document does not apply to the following equipment and related components in the pressure equipment system.
a) instrumentation and control equipment;
b) electrical equipment;
c) buildings and structures;
d) Mechanical parts other than pump casings and compressor casings in pumps and compressors.
2 Normative references
The contents of the following documents constitute essential provisions of this document through normative references in the text. Among them, dated citations documents, only the version corresponding to that date applies to this document; for undated references, the latest edition (including all amendments) applies to this document.
GB/T 150 (all parts) Pressure Vessels
GB/T 19624 Safety Assessment of Defective Pressure Vessels in Service
GB/T 26610.2 Implementation Guide for Risk-Based Inspection of Pressure Equipment Systems Part 2.Risk-Based Inspection Strategy
GB/T 26610.4 Implementation Guide for Risk-Based Inspection of Pressure Equipment Systems Part 4.Quantitative Analysis Method of Failure Probability
GB/T 26610.5 Implementation Guidelines for Risk-Based Inspection of Pressure Equipment Systems Part 5.Quantitative Analysis Methods for Failure Consequences
GB/T 30579 Damage Pattern Recognition of Pressure Equipment
GB/T 35013 Evaluation of the suitability of pressure equipment for use
3 Terms and Definitions
The following terms and definitions apply to this document.
......
This preview omits tables, figures, formulas and parts of the technical clauses. The complete document — 29 pages — is available in the English PDF.
Referenced standards
Normative references
- GB/T 19624Safety assessment of in-service pressure vessels containing defects
- GB/T 26610.2Guideline for implementation of risk-based inspection of pressure equipment system—Part 2:Risk-based inspection plan
- GB/T 26610.4Guideline for implementation of risk-based inspection of pressure equipment system—Part 4: Quantitative analysis approach of failure likelihood
- GB/T 26610.5Guideline for implementation of risk-based inspection of pressure equipment system—Part 5: Quantitative analysis approach of failure consequence
- GB/T 30579Damage modes identification for pressure equipments
- GB/T 35013Fitness-for-service assessment of pressure equipments
GB/T 150
Cited by
- GB/T 33578.4-2026Rules for risk-based inspection of complete units — Part 4: Parabolic trough solar thermal power plants
- GB/T 30578-2025Risk-based inspection and evaluation for atmospheric pressure storage tanks
- GB/T 26610.2-2022Guideline for implementation of risk-based inspection of pressure equipment system—Part 2:Risk-based inspection plan
- GB/T 26610.4-2022Guideline for implementation of risk-based inspection of pressure equipment system—Part 4: Quantitative analysis approach of failure likelihood
- GB/T 33578.1-2017Guideline of risk based inspection of complete units—Part 1: Ethylene units
- GB/T 33578.2-2017Guideline of risk based inspection of complete units—Part 2: Catalytic cracking units
Similar standards
Editions of GB/T 26610.1
| Edition | Title | Revision | Status |
|---|---|---|---|
| GB/T 26610.1-2022 | Guideline for implementation of risk-based inspection of pressure equipment system—Part 1: Basic requirements and implementation procedure | current edition | Current |
| GB/T 26610.1-2011 | Guideline for implementation of risk-based inspection of pressure equipment system—Part 1: Basic requirements and implementation procedure | previous edition | Superseded |
This page sells the current edition, GB/T 26610.1-2022. Earlier editions are listed for reference only.
How to Download GB/T 26610.1-2022
- 1
Add to cart
Click "Download PDF" on this page and choose "Buy this standard". You can add more standards before checkout.
- 2
Checkout
Enter your email and billing details. Payment is processed securely by Stripe (cards or bank transfer). Prefer bank details? Request a quotation (min. order $300).
- 3
Instant delivery (0–9 sec)
Delivery is automatic: within seconds of payment you'll receive an email with a secure download link. The link stays valid for 72 hours.
- 4
Invoice included
A tax invoice is attached to the confirmation email. Need a custom invoice? Contact us.
Related Standards
GB/T 150.1-2024 — Pressure vessels - Part 1: General requirements
GB/T 150.2-2024 — Pressure vessels - Part 2: Materials
GB/T 150.3-2024 — Pressure vessels - Part 3: Design
Secure payment via Stripe
Payments accepted
GB/T 26610.1-2022
$480.00