Valid

GB 4717-2024Fire alarm control units (English PDF)

火灾报警控制器

Preview PDF

This is a limited preview

Buy now to download the full PDF (75 pages)

Need quotation for your management?

Get a formal quotation for GB 4717-2024 in 30 minutes.

Issued by

State Administration for Market Regulation; Standardization Administration of China

Level / Type

National · Mandatory

Issue date

April 29, 2024

Implementation date

May 1, 2025

Scope

GB 4717-2024 is the English-translated version of 火灾报警控制器.

GB 4717-2024 is the Chinese standard "Fire alarm control units".

Its scope clause reads: This document defines the terms and definitions of fire alarm controllers, specifies the classification and nomenclature, requirements, inspection rules and markings, and describes the relevant Appropriate test method: This document applies to the design, manufacture and use of fire alarm controllers (hereinafter referred to as controllers) used in industrial and civil buildings: test:. Its clauses include terms and definitions.

Found what you need?

Document preview — GB 4717-2024

National Standard of the People's Republic of China

ICS: 13.220.20
Classification: C81

Issued by: State Administration for Market Regulation; Standardization Administration of China

Preface
1 Scope
2 Normative references
3 Terms and Definitions
4 Classification and naming
5 Requirement
6 Test methods
7 Inspection Rules
8 Sign
Appendix A (Normative) Controller housing combustion performance
Appendix B (Normative) Controller operation data storage unit
Appendix C (Normative) Fire protection system equipment control bus communication protocol
References

1 Scope

This document defines the terms and definitions of fire alarm controllers, specifies the classification and nomenclature, requirements, inspection rules and markings, and describes the relevant

Appropriate test method:

This document applies to the design, manufacture and use of fire alarm controllers (hereinafter referred to as controllers) used in industrial and civil buildings:

test:

2 Normative references

The contents of the following documents constitute the essential clauses of this document through normative references in this document:

For referenced documents without a date, only the version corresponding to that date applies to this document; for referenced documents without a date, the latest version (including all amendments) applies to

This document:

GB/T 4208-2017 Enclosure protection degree (IP code)

GB/T 9969 General principles for instructions for use of industrial products

GB 12978 Inspection Rules for Fire Protection Electronic Products

GB 16806 Fire linkage control system

GB/T 16838 Environmental test methods and severity levels for fire protection electronic products

GB/T 17626:2 Electromagnetic compatibility test and measurement technology Electrostatic discharge immunity test

GB/T 17626:3 Electromagnetic compatibility test and measurement technology Radio frequency electromagnetic field radiation immunity test

GB/T 17626:4 Electromagnetic compatibility test and measurement technology Electrical fast transient pulse group immunity test

GB/T 17626:5 Electromagnetic compatibility test and measurement technology Surge (impact) immunity test

GB/T 17626:6 Electromagnetic compatibility test and measurement technology - Immunity to conducted disturbances induced by radio frequency fields

GB/T 17626:11 Electromagnetic compatibility test and measurement technology Part 11: For each phase input current less than or equal to 16A

Voltage dips, short interruptions and voltage variations immunity test for equipment

3 Terms and definitions

The following terms and definitions apply to this document:

3:1

Disabled condition

The state the controller is in after the muting function is activated:

3:2 fire alarm signalfirealarmsignal

The signal sent by the fire alarm trigger device when the monitoring parameters of the fire alarm trigger device meet the fire alarm conditions:

3:3

Fire alarm status firealarmcondition

The state of the controller when it issues a fire alarm prompt message after receiving a fire alarm signal:

3:4

Fault alarm signalfaultalarmsignal

A signal sent when the automatic fire alarm system equipment malfunctions and cannot operate normally:

......
This preview omits tables, figures, formulas and parts of the technical clauses. The complete document — 75 pages — is available in the English PDF.

Referenced standards

Normative references

GB/T 17626

Cited by

Similar standards

GB 12791-2006|GB 12978-2025|GB 16806-2006|GB 16808-2025|GB 17429-2011

Editions of GB 4717

Edition	Title	Revision	Status
GB 4717-2024	Fire alarm control units	current edition	Current
GB 4717-2005	Fire alarm control units	previous edition	Superseded

This page sells the current edition, GB 4717-2024. Earlier editions are listed for reference only.

How to Download GB 4717-2024

1
Add to cart
Click "Download PDF" on this page and choose "Buy this standard". You can add more standards before checkout.
2
Checkout
Enter your email and billing details. Payment is processed securely by Stripe (cards or bank transfer). Prefer bank details? Request a quotation (min. order $300).
3
Instant delivery (0–9 sec)
Delivery is automatic: within seconds of payment you'll receive an email with a secure download link. The link stays valid for 72 hours.
4
Invoice included
A tax invoice is attached to the confirmation email. Need a custom invoice? Contact us.