GB/T 9465-2018Vehicle-mounted mobile elevating work platforms (English PDF)

Foreword

This standard was drafted in accordance with the rules given in GB/T 1.1-2009.

This standard replaces GB/T 9465-2008 "High-altitude work vehicle". Compared with GB/T 9465-2008, except for editorial changes, mainly

The technical changes are as follows.

--- Removed the "Basic Parameter Series for Work Vehicles" requirement (see.2008 edition 4.3);

---Modified Chapter 3 aerial work vehicle, maximum working platform height, minimum working platform height, maximum working height, maximum operation

Amplitude, rated load definition, deleted the definition of aerial work platform (see.2008 edition 3.2), increased mobile lift work level

Taiwan (see 3.2), minimum operating height (see 3.7) definition;

---Working environment conditions increase the relative humidity regulations of insulated working vehicles (see 5.1.9);

--- Increased the requirements for the safety performance of modified vehicles (see 5.1.3, 5.1.5);

--- Increased the limit of the "outer edge speed" of the swing speed (see 5.8.3);

--- Revised the calculation requirements for stability and structural safety (see 5.3.3, 5.3.5);

--- Increased the safety provisions of the work platform (see 5.7.6, 5.7.12, 5.7.15), aerial work vehicles greater than 30m should be equipped with anemometer

(see 5.7.14), interlocking of the leg and extension structure (see 5.7.2), safety requirements for the safety of the rated load of the work vehicle (see 5.7.16~5.7.18);

--- Increased the safety performance requirements of hydraulic system actuators (see 5.4), improved the platform sinking capacity under rated load (see

5.8.5,.2008 edition 5.7.5);

--- Increased control requirements for electrical systems (see 5.5);

--- Revise the maximum working platform height error to 1% (see 5.8.6,.2008 version 5.7.6);

--- Increased 20kV, 500kV grade insulated aerial work vehicle content (see Table 3,.2008 edition table 4);

1 Scope

This standard specifies the terms and definitions, classification and model, technical requirements, test methods, inspection rules, signs, packaging, and

Transportation and storage.

This standard is applicable to aerial work vehicles with a maximum working height of not more than 100m (hereinafter referred to as work vehicles).

2 Normative references

The following documents are indispensable for the application of this document. For dated references, only dated versions apply to this document. For undated references, the latest edition (including all amendments) applies to this document.

GB/T 507 insulation oil breakdown voltage measurement method

GB 1589 Car, trailer and car train profile size, axle load and mass limit General rules and safety requirements for GB/T 3766 hydraulic drive systems and their components

GB 3847 Automotive Compression Ignition Engine and Compression Ignition Engine Exhaust Smoke Emission Limits and Measurement Methods

GB/T 4208-2017 enclosure protection grade (IP code)

GB 5226.1-2008 Mechanical electrical safety machinery and electrical equipment - Part 1. General technical conditions

GB 7258 Motorcycle Operation Safety Technical Conditions General technical requirements for GB/T 7935 hydraulic components

GB/T 9969 General guidelines for the use of industrial products

GB 11567 Protection requirements for side and rear parts of automobiles and trailers

GB/T 12534 General rules for road test methods

GB/T 14039-2002 Hydraulic transmission oil solid particle pollution level code

GB/T 14048.5 Low-voltage switchgear and controlgear - Part 5-1. Electromechanical control of control circuit electrical and switching components Circuit electrical appliance

GB/T 16927.1 High Voltage Test Technique Part 1. General Definitions and Test Requirements

GB 17691 Combustion-type, gas-fueled ignition engine and vehicle exhaust pollutant emission limits and measurement methods (China III, IV, V stage)