GB/T 23505-2017Petroleum and natural gas industries - Petroleum drilling and workover rigs (English PDF)

Foreword

This standard is drafted in accordance with the rules given in GB/T 1.1-2009.

This standard replaces GB/T 23505-2009 "oil rigs and workover rigs". Compared with GB/T 23505-2009, the main technology changes As follows.

--- Standard name changed to "oil and gas industry drilling rig and workover rig";

- Added or removed some normative references (see Chapter 2);

- to modify all the terms and definitions in the original standard, and to remove the terms "design safety factor", the addition of "drilling mechanization equipment" (See 3.1);

--- Change the type of chassis in the representation of the workover model to the type of movement (see 4.2.2);

- Table 1 adds the ZJ80/5850 level rig (see Table 1);

--- Table 2 in the hook level 1800,2250 increase in 39m, 41m two derrick height (see Table 2);

--- increased the type of power system configuration, increased the configuration of drilling mechanized equipment (see Chapter 6);

- adjust the order of description of 6.2 (see 6.2);

--- Removed the requirements for safe escape chute and ground angle, the requirements for guard railings, the number of safety protection chains and the requirements Installation of TV room monitoring system for motor room (see Chapter 6);

- Describe the technical requirements sub-system and consolidate the original terms (see Chapter 7);

- Electricity of rig electrical equipment increases by 600V/400V, 50Hz specification (see 7.2);

- only the module rig derives the ladder leading to the trolley and the second floor to all derricks (see 7.3);

- Increased requirements for self-propelled rigs and workover vehicles (see 7.9);

--- Increased installation of oil, water, electricity and heating systems for drilling wells (see 7.10);

- change the specific requirements for the coating in the standard to SY/T 6919 (see 7.1);

- Increased test requirements for self-propelled rigs and workover rigs (see 8.1, 8.2);

- Change the requirements for the winch type test to SY/T 5532 (see 8.2);

- Increased requirements for drilling pump type tests, turntable and top drive drilling unit type inspection requirements (see 8.2).

1 Scope

This standard specifies the terms and definitions of oil and gas rigs and workover rigs, product type, model, basic parameters, configuration requirements, technical requirements, testing and recording, marking, factory documentation, storage, packaging and transportation.

This standard applies to oil and gas drilling and workover rigs and workover rigs. Offshore platforms with rigs and workover rigs can be consulted.

2 Normative reference documents

The following documents are indispensable for the application of this document. For dated references, only the dated edition applies to this article Pieces. For undated references, the latest edition (including all modifications) applies to this document.

GB 146.1 Standard Gauge Rail Locomotive Vehicle Boundary

GB 2894 Safety signs and guidelines for their use

GB/T 3766 General technical requirements for hydraulic systems

GB 3836.1 Explosive atmospheres - Part 1: General requirements for equipment

GB 3836.2 Explosive atmospheres - Part 2: Equipment protected by flameproof enclosure "d"

GB 3836.3 Explosive atmospheres - Part 3: Equipment protected by increased safety type "e"

GB 3836.5 Electrical equipment for explosive gas atmospheres - Part 5: Positive pressure shell type "p"

GB 3836.8 Explosive atmospheres - Part 8: Equipment protected by "n" type

GB 3836.15 Electrical equipment for explosive gas atmospheres - Part 15: Electrical installations in hazardous locations (except coal mines)

GB 4208 enclosure protection class (IP code)

GB/T 7932 General technical requirements for pneumatic systems

GB/T 7935 General specification for hydraulic components

GB/T 23507.3 Specification for electrical equipment for oil rigs - Part 3: Diesel generator sets for electric drilling rigs

GB/T 30216-2013 vehicle mounted rig

SY/T 5027 Pneumatic components for oil drilling equipment

SY/T 5030 Oil and Gas Industry Diesel Engine

SY/T 5074 Drilling and workover power tongs, hanging clamps

SY/T 5080 turntable for oil rig and workover rig