GB/T 13773.1-2008Textiles -- Seam tensile properties of fabrics and made-up textile articles -- Part 1: Determination of maximum force to seam rupture using the strip method (English PDF)

Foreword

GB/T 13773 Textiles - Seam tensile properties of fabrics and made-up textile articles is

divided into 2 parts.

— Part 1. Determination of maximum force to seam rupture using the strip method

— Part 2. Determination of maximum force to seam rupture using the grab method

This part is Part 1 of GB/T 13773.

This part uses translation method to equivalently adopt ISO 13935-1.1999 Textiles - Seam

tensile properties of fabrics and made-up textile articles - Part 1. Determination of

maximum force to seam rupture using the strip method.

Compared with ISO 13935-1.1999, this part makes the following editorial modifications.

— Normative referenced international standards are replaced by the equivalent

standards or Chinese standards that are corresponding to the international

standards;

— Foreword, introduction, informative annex A and bibliography of the international

standards have been deleted.

This part replaces GB/T 13773-1992 Method B. Compared with GB/T 13773-1992, the

main technical differences are as follows.

1 The above standards are characterized into that - one original independent standard

is adjusted into a series of standards, including two parts. The Part 1 is regarded as

the B method of the original standard and the Part 2 is regarded as the A method of

the original standard; the standard name is also amended correspondingly;

2 For the scope, woven fabrics and made-up articles are expanded; and inapplicable

products are added;

3 Relative standards of a stretching tester are added in the normative reference

document; and reference of partial standards is deleted;

4 CRE stretching tester, strip test and gauge length have been added in terms of

Chapter 3; and seaming stitch density, seam and seaming efficiency have been

deleted;

5 CRT strength tester has been deleted and concrete requirements have been

proposed for the CRE stretching tester;

6 Relative clauses of stitching parameters have been deleted and determined

according to an agreement;

Textiles - Seam tensile properties of fabrics and

made-up textile articles - Part 1. Determination of

maximum force to seam rupture using the strip

method

1 Scope

This part of GB/T 13773 specifies a procedure to determine the seam maximum force of

sewn seams when the force is applied perpendicularly to the seam, and specifies the

method known as the strip test.

This part is mainly applicable to woven textile fabrics. It can be applicable to fabrics

produced by other techniques. It is not normally applicable to woven elastic fabrics,

geotextiles, nonwovens, coated fabrics, textile-glass woven fabrics and fabrics made from

carbon fibres or polyolefin tape yarns.

The sewn fabrics may be obtained from previously sewn articles or may be prepared from

fabric samples, as agreed by the parties interested in the results.

This method is applicable to straight seams only and not to curved seams.

The method is restricted to the use of constant rate of extension (CRE) testing machines.

2 Normative references

The articles contained in the following documents have become this part of GB/T 13773

when they are quoted herein. For the dated documents so quoted, all the modifications

(excluding corrections) or revisions made thereafter shall not be applicable to this part.

For the undated documents so quoted, the latest editions shall be applicable to this part.

GB/T 6529 Textiles - Standard atmospheres for conditioning and testing (GB/T

6529-2008, ISO 139.2005, MOD)

GB/T 16825.1 Verification of static uniaxial testing machines - Part 1.

Tension/compression testing machines - Verification and calibration of the

force-measuring system (GB/T 16825.1-2008, ISO 7500-1.2004, IDT)

GB/T 19022 Measurement management systems - Requirements for measurement

processes and measuring equipment (GB/T 19022-2003, ISO 10012.2003, IDT)

3 Terms and definitions

For the purpose of this part of GB/T 13773, the following terms and definitions shall apply.

3.1

Constant-rate-of-extension (CRE) testing machine

Tensile-testing machine provided with one clamp which is stationary and another clamp

which moves with a constant speed throughout the test, the entire testing system being

virtually free from deflection.

3.2

Strip test

Tensile test in which the full width of the test specimen is gripped in the jaws of the testing

machine.

3.3

Maximum force to seam rupture

Maximum force recorded when a test specimen with a seam perpendicular to the direction

of extension is taken to seam rupture during a tensile test under the specified conditions.

3.4

Gauge length

Distance between the two effective clamping points of a testing device.

Note . The effective clamping points (or lines) of jaws can be checked by clamping a test specimen under

defined pretension with carbon copy paper to produce a gripping pattern on the test specimen and/or the

jaw faces.

4 Principle

A fabric test specimen of specified dimensions having a seam in the middle is extended

perpendicularly to the seam at a constant rate until the seam ruptures. The maximum

force to seam rupture is recorded.

5 Sampling

Select samples either in accordance with the procedure laid down in the material

specification for the fabric, or as agreed between the interested parties.

......