GB/T 10489-2009General requirements for aero-derivative gas turbines (English PDF)
轻型燃气轮机 通用技术要求
This is a limited preview
Buy now to download the full PDF (20 pages)
Need quotation for your management?
Get a formal quotation for GB/T 10489-2009 in 30 minutes.
Issued by
SAMR; SAC
Level / Type
National · Recommended
Issue date
April 13, 2009
Implementation date
January 1, 2010
Scope
GB/T 10489-2009 is the English-translated version of 轻型燃气轮机 通用技术要求.
GB/T 10489-2009 is the Chinese standard "General requirements for aero-derivative gas turbines". Its scope clause reads: The standard supply and demand sides to discuss the purchase of light gas turbine and auxiliary equipment providing performance, environmental, safety, technology and other aspects of the fuel Surgery information.
This standard applies to power generation and mechanical drive with a lightweight turbine open cycle, is based on both the supply and demand for technical consultations. Its clauses include terms and definitions; standard reference conditions.
Found what you need?
Document preview — GB/T 10489-2009
National Standard of the People's Republic of China
- ICS
- 27.040
- Classification
- K 56
- Replacing
- GB/T 10489-1989
Issued by: State Administration for Market Regulation; Standardization Administration of the PRC
Contents
- Introduction
- 1 Scope
- 2 Normative references
- 3 Terms and definitions
- 4 standard reference conditions
- 5 Test Fuel
- 6 Run
- 7 rated properties
- 8 control and protection
- 9 6 fuel
- 10 Environment
- 11 inquiry or technical information required shall provide the tender
- Appendix A (normative) Safety measures
- Annex B (informative) Additional information on fuel
- Annex C (informative) Maintenance
- References
1 Scope
The standard supply and demand sides to discuss the purchase of light gas turbine and auxiliary equipment providing performance, environmental, safety, technology and other aspects of the fuel
Surgery information.
This standard applies to power generation and mechanical drive with a lightweight turbine open cycle, is based on both the supply and demand for technical consultations.
2 Normative references
The following documents contain provisions which, through reference in this standard and become the standard terms. For dated references, subsequent
Amendments (not including errata content) or revisions do not apply to this standard, however, encourage the parties to the agreement are based on research
Whether the latest versions of these documents. For undated reference documents, the latest versions apply to this standard.
GB/T 10491 light gas turbine equipment and methods of measurement noise value
GB/T 11369 Flue gas turbine pollutant measuring light
GB/T 14100 gas turbine acceptance test
GB/T 15135 turbine vocabulary (GB/T 15135-2002, ISO 11086.1996, MOD)
3 Terms and Definitions
GB/T 15135 and established the following terms and definitions apply to this standard.
3.1 Aviation derived (derived) Gas Turbine
Aviation turbine engines based on modifications of the gas turbine is derived from the development of non-aviation purposes.
3.2
Including light gas turbine power plant, and to ensure the normal operation of the load device, as well as other to improve its use of performance, control its
Environmental impact types of equipment needed.
3.3
Given the stable operation of the gas turbine by the light it began to accelerate and stop speed.
4 standard reference conditions
4.1 compressor inlet conditions
Compressor inlet flange (or bell at the compressor inlet).
Total pressure 101.3kPa;
Total temperature 15 °C;
60% relative humidity, in addition to the use of an intermediate cooling or water cooling, the humidity can generally be ignored.
4.2 exhaust conditions
Power turbine exhaust outlet flange member (such as the use of heat recovery cycle, the heat in the back at the outlet) static pressure is 101.3kPa.
4.3 Cooling water conditions
When using water-cooled refrigerant, the entrance to the water temperature is taken as 15 °C.
......
This preview omits tables, figures, formulas and parts of the technical clauses. The complete document — 20 pages — is available in the English PDF.
Referenced standards
Normative references
Cited by
- GB/T 33631-2017General requirements for inlet and exhaust system of aero-derivative gas turbine assembly
- GB/T 10491-2010Noise criteria and sound measurement procedures for aero-derivative gas turbines turnkey installations
- GB/T 13673-2010General requirements for aero-derivative gas turbines auxiliary equipment
- GB/T 11371-2008Operation and maintenance for gas turbine
- GB/T 14411-2008Control and protective system for aero-derivative gas turbine
- GB/T 16637-2008General requirements for gas turbine electrical equipment
Similar standards
Editions of GB/T 10489
| Edition | Title | Revision | Status |
|---|---|---|---|
| GB/T 10489-2009 | General requirements for aero-derivative gas turbines | current edition | Current |
| GB/T 10489-1989 | General requirements for aero-derivative gas turbines | previous edition | Superseded |
This page sells the current edition, GB/T 10489-2009. Earlier editions are listed for reference only.
How to Download GB/T 10489-2009
- 1
Add to cart
Click "Download PDF" on this page and choose "Buy this standard". You can add more standards before checkout.
- 2
Checkout
Enter your email and billing details. Payment is processed securely by Stripe (cards or bank transfer). Prefer bank details? Request a quotation (min. order $300).
- 3
Instant delivery (0–9 sec)
Delivery is automatic: within seconds of payment you'll receive an email with a secure download link. The link stays valid for 72 hours.
- 4
Invoice included
A tax invoice is attached to the confirmation email. Need a custom invoice? Contact us.
Related Standards
GB/T 10491-2010 — Noise criteria and sound measurement procedures for aero-derivative gas turbines turnkey installations
GB/T 11369-2008 — Measurement of exhaust gas emission for aero-derivative gas tubine
GB/T 14100-2016 — Gas turbines -- Acceptance tests
Secure payment via Stripe
Payments accepted
GB/T 10489-2009
$355.00