Valid

GB/T 10478-2017Railway tank car for liquefied gases (English PDF)

液化气体铁路罐车

Preview PDF

This is a limited preview

Buy now to download the full PDF (39 pages)

Need quotation for your management?

Get a formal quotation for GB/T 10478-2017 in 30 minutes.

Issued by

SAMR; SAC

Level / Type

National · Recommended

Issue date

October 14, 2017

Implementation date

May 1, 2018

Scope

GB/T 10478-2017 is the English-translated version of 液化气体铁路罐车.

GB/T 10478-2017 is the Chinese standard "Railway tank car for liquefied gases". Its scope clause reads: This standard specifies the liquefied gas railway tanker (hereinafter referred to tanker) materials, design, manufacture, test methods, inspection rules, coating and Mark identification, factory documents and other requirements.

This standard applies to the design pressure of steel tanks is not less than 0.1MPa, and the permanent connection with the walking device standard gauge tanker.

This standard does not apply to the following tanker. a) The tank material is non-ferrous or non-metallic; b) the tank is a vacuum insulation structure; c) Tanks have special requirements for the defense of military equipment.

The scope of this standard tanker tank, including piping, safety accessories, instruments and handling attachments, as well as walking devices, running gear and tanks Body connectors and so on.

Found what you need?

Document preview — GB/T 10478-2017

National Standard of the People's Republic of China

ICS: 45.060.10
Classification: S 52
Replacing: GB/T 10478-2006

Issued by: State Administration for Market Regulation; Standardization Administration of the PRC

Preface
Introduction
1 Scope
2 Normative references
3 Terms and definitions
4 Qualifications and Responsibilities
5 material
6 design
7 safety accessories, instruments and handling valve
9 Test Methods
11 mark,
12 factory documents
Appendix A (Normative) Risk Assessment Report
Appendix B (Normative) Tank safe discharge and safety relief device discharge capacity calculation

1 Scope

1.1

This standard specifies the liquefied gas railway tanker (hereinafter referred to tanker) materials, design, manufacture, test methods, inspection rules, coating and

Mark identification, factory documents and other requirements.

1.2

This standard applies to the design pressure of steel tanks is not less than 0.1MPa, and the permanent connection with the walking device standard gauge tanker.

1.3

This standard does not apply to the following tanker.

a) The tank material is non-ferrous or non-metallic;

b) the tank is a vacuum insulation structure;

c) Tanks have special requirements for the defense of military equipment.

1.4

The scope of this standard tanker tank, including piping, safety accessories, instruments and handling attachments, as well as walking devices, running gear and tanks

Body connectors and so on.

1.5

tank body defined as follows.

a) the groove face of the first circumferential joint of the tank body and the pipeline welded and connected;

b) The first threaded joint end face of the tank body, pipeline and safety accessory thread, the first flange sealing face of flange connection;

c) End caps, end plugs and fasteners of the open part of the tank;

d) Weld connection between tank and non-pressured element.

1.6

The main pressure tank components, including the cylinder, the head and the nominal diameter of not less than 50mm take over (pressure), flange, flange, flange cover

Board and so on.

1.7

pipeline includes all connected with the tank and pipe fittings.

2 Normative references

The following documents for the application of this document is essential. For dated references, only the dated version applies to this article

Pieces. For undated references, the latest edition (including all amendments) applies to this document.

GB 146.1 standard gauge railway rolling stock limits

Pressure vessels Part 1 GB/T 150.1 General requirements

GB/T 150.2 Pressure vessels Part 2. Materials

Pressure vessels Part 3 GB/T 150.3 Design

Pressure vessels - Part 4. Manufacture, inspection and acceptance

GB/T 196 ordinary thread basic size

GB/T 197 ordinary thread tolerances

GB/T 567.1 bursting disc safety device - Part 1. Basic requirements

GB/T 567.2 Bursting disc safety devices - Part 2. Application, selection and installation

GB/T 567.3 bursting disc safety device Part 3 Classification and installation dimensions

GB/T 713 boiler and pressure vessel steel

GB/T 1804-2000 General tolerances Tolerances for linear and angular dimensions without tolerance

GB/T 3531 low temperature pressure vessel steel

GB/T 4549 (all parts) railway vehicle vocabulary […]

......
This preview omits tables, figures, formulas and parts of the technical clauses. The complete document — 39 pages — is available in the English PDF.

Referenced standards

Normative references

GB/T 567.2 · GB/T 713 · GB/T 3531 · GB/T 4549

Cited by

Similar standards

GB/T 33192-2026|GB/T 25334.1-2023|GB/T 25334.2-2023|GB/T 3316-2019|GB/T 25333-2010|GB/T 14894-2026

Editions of GB/T 10478

Edition	Title	Revision	Status
GB/T 10478-2017	Railway tank car for liquefied gases	current edition	Current
GB/T 10478-2006	Railway tank car for liquefied gases	previous edition	Superseded

This page sells the current edition, GB/T 10478-2017. Earlier editions are listed for reference only.

How to Download GB/T 10478-2017

1
Add to cart
Click "Download PDF" on this page and choose "Buy this standard". You can add more standards before checkout.
2
Checkout
Enter your email and billing details. Payment is processed securely by Stripe (cards or bank transfer). Prefer bank details? Request a quotation (min. order $300).
3
Instant delivery (0–9 sec)
Delivery is automatic: within seconds of payment you'll receive an email with a secure download link. The link stays valid for 72 hours.
4
Invoice included
A tax invoice is attached to the confirmation email. Need a custom invoice? Contact us.