Valid

QC/T 29106-2004Technical specifications for automotive low-voltage wire harnesses (English PDF)

汽车低压电线束技术条件

Preview PDF

This is a limited preview

Buy now to download the full PDF (15 pages)

Need quotation for your management?

Get a formal quotation for QC/T 29106-2004 in 30 minutes.

Issued by

MIIT

Level / Type

Industry · Recommended

Issue date

February 10, 2004

Implementation date

August 1, 2004

Scope

QC/T 29106-2004 is the English-translated version of 汽车低压电线束技术条件.

QC/T 29106-2004 is the Chinese standard "Technical specifications for automotive low-voltage wire harnesses". Its scope clause reads: This standard specifies the requirements, test methods, inspection rules, signs, package, storage and safekeeping of the low-voltage electric harness for motor vehicles (hereinafter referred to as electric harness).

This standard is applicable to various electric harnesses for motor vehicles (including single-wire) with the nominal voltage less than 50v. Its clauses include terms and definitions; requirements.

Found what you need?

Document preview — QC/T 29106-2004

National Standard of the People's Republic of China

Replacing: QC/T 29106-1992

Issued by: Ministry of Industry and Information Technology of the People's Republic of China

Contents
Foreword
1 Scope
2 Normative References
3 Terms and Definitions
4 Requirements
5 Test Methods
6 Test rules
7 Mark, package, storage and safekeeping

1 Scope

This standard specifies the requirements, test methods, inspection rules, signs, package, storage and safekeeping of the low-voltage electric harness for motor vehicles (hereinafter referred to as electric harness).

This standard is applicable to various electric harnesses for motor vehicles (including single-wire) with the nominal voltage less than 50v.

2 Normative References

The following documents contain provisions which, through reference in this standard, constitute provisions of this standard. For dated references, subsequent amendments (excluding corrigendum content) to, or revisions of, any of these publications do not apply in this standard. However, parties coming to an agreement according to this standard are encouraged to study whether the latest editions of these documents are applicable. For any undated references, the latest edition of the normative document referred to applies.

GB/T 2828.1-2003 Sampling Procedures For Inspection By Attributes-Part 1: Sampling Schemes Indexed by Acceptance Quality Limit (AQL) for Lot-by-lot Inspection

GB 11121 Gasoline Engine Oils

GB 17930 Unleaded Petrol (Gasoline) for Motor Vehicles

GB/T 13527.2 Plasticized Polyvinyl Chloride Tubing (for Electrical Insulation)

HG/T 2196 Rubber Materials for Motor Vehicles

JB/T 6313.1 Braided Copper Wires for Electrical Purposes General Regulations

JB/T 6313.2 Braided Copper Wires for Electrical Purposes Diagonal Braided Wires

JB/T 6313.3 Braided Copper Wires for Electrical Purposes Plain Braided Wires

JB/T 8139 Low-voltage Cable ( Wire ) for Road Vehicles

JJG 4 Steel Tape

QB/T 2423 Electric-Insulation Pressure Sensitive Adhesive Tape with Polyvinyl Chloride (PVC)

QC/T 238 Storage and Safekeeping of the Automobile Parts

QC/T 413—2002 Basic Technical Requirements for Automotive Electric Equipment

QC/T 414 The Color of the Low-voltage Wire for Automobile

QC/T 417.1 Electric harness Connector for Vehicles Part 1: Definition, Test Methods and General Performance Requirements (The Automobile Part)

QC/T 417.3 Electric harness Connector for Vehicles Part 3: The dimension and Special Requirements of the Single Blade Connector

QC/T 417.4 Electric harness Connector for Vehicles Part 4: The dimension and Special Requirements of the Multiple Blade Connector

QC/T 417.5 Electric harness for Vehicles Part 5: The Dimension and Special Requirements of the Column Connector for the Single and multiple Connector

QCn 29010 Low-voltage Wire Terminal for Automobile Form, Dimension and Technical Requirements

QCn 29013 Storage Battery Wire Terminal for Automobile Form, Dimension and Technical Requirements

3 Terms and Definitions

This standard adopts the following definitions and those in QC/T 417.1.

3.1 Main stem

The part that two or more than two wires in the electric harness are wrapped up together (as shown in Figure 1).

3.2 Lateral

The part that the end of the wire in the electric harness is unwrapped up or the single wire (as shown in Figure 1).

3.3 Embranchment point

The intersection between main stems or the intersection between the main stem and the centerline of the lateral in the electric harness(as shown in Figure 1).

3.4 Juncture

The connection point between wires (as shown in Figure 1).

3.5 Terminal

The general term of the connector and the joint.

3.6 Desiccation bound

The area in which the electric harness (being installed in the cab, the crew compartment and the luggage compartment etc.) needs no waterproof protection.

3.7 Damp bound

In addition to the desiccation bound, the area in which the electric harness needs no special waterproof protection.

3.8 SKT

The connection mode that the terminal connects with the wire conductor by piercing the wire insulation layer to achieve good electrical contacts and certain tensile strength..

The sheath hole position size Wire size Main stem Embranchment point Lateral Juncture

Figure 1

4 Requirements

4.1

The electric harness shall meet the requirements in this standard and shall be manufactured according to the drawings and technical documents approved through the prescribed procedure.

4.2

The dimension of the electric harness shall meet the following requirements:

4.2.1

The length of the main stem and the protective sleeve pipe shall be more than or equal to 100mm and be the multiple of 10. e.g. 100mm, 110mm and 120mm.

4.2.2

The length of the lateral shall be more than or equal to 30mm.

4.2.3

The distance between junctures, between the juncture and the embranchment point shall be more than or equal to 20mm.

4.2.4

While it is required to install the insulation sleeve pipe in the connection between the wire and the terminal, the length of the insulation sleeve pipe shall be more than or equal to 20mm.

4.2.5 The basic dimension limit dev

......
This preview omits tables, figures, formulas and parts of the technical clauses. The complete document — 15 pages — is available in the English PDF.

Referenced standards

Cited by

Similar standards

QC/T 1067.1-2017|QC/T 1067.2-2017|QC/T 1067.3-2017|QC/T 774-2006|QC/T 730-2005|GB/T 36516-2018

Editions of QC/T 29106

Edition	Title	Revision	Status
QC/T 29106-2004	Technical specifications for automotive low-voltage wire harnesses	current edition	Current
QC/T 29106-1992	Technical specifications for automotive low-voltage wire harnesses	previous edition	Superseded

This page sells the current edition, QC/T 29106-2004. Earlier editions are listed for reference only.

How to Download QC/T 29106-2004

1
Add to cart
Click "Download PDF" on this page and choose "Buy this standard". You can add more standards before checkout.
2
Checkout
Enter your email and billing details. Payment is processed securely by Stripe (cards or bank transfer). Prefer bank details? Request a quotation (min. order $300).
3
Instant delivery (0–9 sec)
Delivery is automatic: within seconds of payment you'll receive an email with a secure download link. The link stays valid for 72 hours.
4
Invoice included
A tax invoice is attached to the confirmation email. Need a custom invoice? Contact us.