GB/T 3820-1997Determination of thickness of textiles and textile products (English PDF)
纺织品和纺织制品厚度的测定
This is a limited preview
Buy now to download the full PDF (11 pages)
Need quotation for your management?
Get a formal quotation for GB/T 3820-1997 in 30 minutes.
Issued by
General Administration of Quality Supervision, Inspection and Quarantine of the People's Republic of China
Level / Type
National · Recommended
Issue date
October 9, 1997
Implementation date
May 1, 1998
Scope
GB/T 3820-1997 is the English-translated version of 纺织品和纺织制品厚度的测定.
GB/T 3820-1997 is the Chinese standard "Determination of thickness of textiles and textile products". Its scope clause reads: This Standard specifies the method for determination of thickness of textiles under specified pressure.
This Standard is applicable to all types of textiles and textile products. Its clauses include definitions; test procedures.
Found what you need?
Document preview — GB/T 3820-1997
National Standard of the People's Republic of China
- ICS
- 59.080.30
- Classification
- W 04
Issued by: General Administration of Quality Supervision, Inspection and Quarantine of the People's Republic of China
Contents
- Foreword3
- 1 Scope4
- 2 Normative references4
- 3 Definitions4
- 4 Principle5
- 5 Equipment5
- 6 Atmospheres for conditioning and testing6
- 7 Sampling and preparation of samples6
- 8 Test procedures7
- 9 Expression of results8
- 10 Test report8
1 Scope
This Standard specifies the method for determination of thickness of textiles under specified pressure.
This Standard is applicable to all types of textiles and textile products.
2 Normative references
The provisions in the following standards become the provisions of this
Standard through reference in this Standard. At the time of publication of this
Standard, the editions shown are valid. All standards will be revised and the parties using this Standard shall explore the possibility of using the latest editions of the following standards.
GB 6529-86 Standard atmospheres for textiles conditioning and testing
GB 8170-87 Rules for rounding off of numerical values
GB/T 19022.1-1994 Quality assurance requirements for measuring equipment - Part 1: Metrological confirmation system for measuring equipment (idt ISO 10012.1:1992)
3 Definitions
The following definitions are applicable to this Standard.
3.1 Thickness of a textile
It refers to the vertical distance between the two reference plates that apply the specified pressure to the textiles.
3.2 Bulky textiles
It refers to the textiles with a thickness variation (compression ratio) of greater than or equal to 20% when the pressure applied to the textiles increases from
0.1kPa to 0.5kPa, such as artificial furs, plush, velvet, nonwoven interlinings, etc.
are in accordance with product standards. If they fail to be specified in detail in the product standards, the method agreed by the parties concerned that is of interest to the test results shall apply.
7.2 Test pieces
7.2.1 The samples collected according to Subclause 7.1 can be directly used as the test pieces. During the test, the measuring parts shall be arranged in a ladder evenly in the area above 150mm from the selvedge. The measuring points are not in the same longitudinal and transverse positions, and shall avoid the flaws and wrinkles that affect the test results.
7.2.2 For samples that are susceptible to deformation or may affect the test operations, such as certain knitted fabrics, nonwovens or wide fabrics and textile products, etc., a sufficient number of test pieces shall be cut in accordance with Table 1. The requirements for sample cutting shall be in accordance with Subclause 7.2.1. The dimensions of the test pieces shall not be less than the presser foot dimensions.
7.3 Conditioning
Before the test, the samples or test pieces shall realize conditioning equilibrium in a relaxed state in the atmosphere specified in Chapter 6. The conditioning method and requirements shall be in accordance with GB 6529. It is generally necessary to perform conditioning for more than 16h. Synthetic fiber samples shall be equilibrated for at least 2h. The samples with a conventional moisture regain of zero can be determined directly.
8 Test procedures
8.1 SELECT the presser foot (5.1.1) according to the sample type in Table 1.
For the samples whose surfaces are of uneven pattern structure, the diameter of the presser foot shall not be less than the length of the pattern cycle. The smaller presser foot can be used to respectively determine and report the thickness of the concave and convex parts, if necessary.
8.2 CLEAN the presser foot (5.1.1) and reference plate (5.1.2) to check the
movement flexibility of the presser foot shaft. SET the pressure according to
Table 1. Then DRIVE the presser foot against the reference plate, and SET the thickness meter (5.1.4) to zero.
8.3 RAISE the presser foot to place the test piece without tension and
deformation on a reference plate.
......
This preview omits tables, figures, formulas and parts of the technical clauses. The complete document — 11 pages — is available in the English PDF.
Referenced standards
Normative references
- GB 6529Standard atmospheres for textiles conditioning and testing
- GB/T 19022.1-1994Quality assurance requirements for measuring equipment--Part1: Metrological confirmation system for measuring equipment
GB 8170
Cited by
- GB 24539-2025Protective clothing - Chemical protective clothing
- GB/T 30788-2025Corrosion control technology for steel pipelines covered by cold-applied petrolatum tape
- GB/T 45362-2025Textiles - Determination of thermal effusivity of fabrics - Modified transient plane source method
- GA 2188-2024Police shoes - Summer boots for immigration police on combat and training
- GA 2189-2024Police shoes - Winter boots for immigration police on combat and training
- GB/T 44139.2-2024Requirements for sleeping bags - Part 2: Raw material properties
How to Download GB/T 3820-1997
- 1
Add to cart
Click "Download PDF" on this page and choose "Buy this standard". You can add more standards before checkout.
- 2
Checkout
Enter your email and billing details. Payment is processed securely by Stripe (cards or bank transfer). Prefer bank details? Request a quotation (min. order $300).
- 3
Fast delivery
After payment you'll receive an email confirmation. The English PDF is sent to the same address, usually within minutes and at the latest within 1 business day.
- 4
Invoice included
A tax invoice is attached to the confirmation email. Need a custom invoice? Contact us.
Related Standards
GB 6529-1986 — Standard atmospheres for textiles conditioning and testing
GB/T 19022.1-1994 — Quality assurance requirements for measuring equipment--Part1: Metrological confirmation system for measuring equipment
GB/T 10003-2026 — Biaxially oriented polypropylene (BOPP) film
GB/T 3820-1997
$75.00