GB/T 31029-2014Aircraft garbage truck (English PDF)
飞机垃圾接收车
This is a limited preview
Buy now to download the full PDF (15 pages)
Need quotation for your management?
Get a formal quotation for GB/T 31029-2014 in 30 minutes.
Issued by
SAMR; SAC
Level / Type
National · Recommended
Issue date
December 5, 2014
Implementation date
June 1, 2015
Scope
GB/T 31029-2014 is the English-translated version of 飞机垃圾接收车.
GB/T 31029-2014 is the national standard for the aircraft garbage truck.
Clause 1 states that the standard specifies the technical requirements, test methods, inspection rules, signs, markings, instructions and packaging, transportation and storage of the civilian transport aircraft garbage receiving vehicle, referred to throughout as the aircraft garbage truck, and that it applies to aircraft garbage trucks converted from all types of commercial vehicle chassis.
The table of contents runs 1 Scope, 2 Normative references, 3 Terms and definitions, 4 Technical requirements, 5 Test method, 6 Inspection rules, 7 Signs, markings and manual, and 8 Packaging, transportation and storage.
The draft breaks off at the end of clause 2, so the terms defined in clause 3 and the content of the later clauses are not shown.
Clause 2 cites a set of road vehicle standards, among them GB 7258 on the safety of motor vehicle operation, GB 4785 on exterior lighting installation, GB 1495 on vehicle noise limits, GB 18285 and GB 20891 on exhaust emission limits, and the GB/T 12534, GB/T 12536, GB/T 12543, GB/T 12544, GB/T 12545.2, GB/T 12547, GB/T 12673, GB/T 12674, GB/T 12677 and GB/T 12678 series of automotive test methods.
It also cites GB/T 3766 and GB/T 7935 on hydraulic systems and components, GB/T 7593 on operator control symbols for powered industrial vehicles, GB/T 9969 on instructions for industrial products, GB/T 50087 on industrial noise control design, JB/T 5943 on welded construction machinery parts, QC/T 413, QC/T 484 and QC/T 625 on automotive electrical equipment and coatings, and the two IATA documents AHM910 on basic requirements for aircraft ground support equipment and AHM915 on standard controls.
The page records the standard as administered by the national air cargo and ground equipment Standardization Technical Committee (SAC/TC359) and drafted by the National Construction Machinery Quality Supervision and Inspection Center. It was issued on 5 December 2014 and has applied since 1 June 2015.
Found what you need?
Document preview — GB/T 31029-2014
National Standard of the People's Republic of China
- ICS
- 49.100
- Classification
- V 57
Issued by: State Administration for Market Regulation; Standardization Administration of the PRC
Contents
- Introduction
- 1 Scope
- 2 Normative references
- 3 Terms and definitions
- 4 2 Technical Requirements Test Method 5
- 6 Inspection Rules
- 7 signs, signs and Manual
- 8 packaging, transportation and storage
Foreword
This standard was drafted in accordance with GB/T 1.1-2009 given rules.
1 Scope
This standard specifies the civilian transport aircraft garbage receiving vehicle (hereinafter referred to as aircraft garbage truck) technical requirements, test methods, inspection rules, Signs, signs, instructions and packaging, transportation and storage.
This standard applies to the use of all types of commercial vehicle chassis modified aircraft garbage truck.
2 Normative references
The following documents for the application of this document is essential. For dated references, only the dated version suitable for use herein Member. For undated references, the latest edition (including any amendments) applies to this document.
GB 1495 vehicle acceleration with the vehicle noise limits and measurement methods
GB/T 3766 Hydraulic System General technical conditions
GB 4785 Installation regulations for car and trailer exterior illumination and light signaling devices
GB 7258 Safety requirements for operation of motor vehicles
GB/T 7593 powered industrial vehicle operator control symbol Devices and other display devices
GB/T 7935 General technical conditions for hydraulic components
GB/T 9969 General Instructions industrial products
GB/T 12534 General Automotive road test method
GB/T 12536 car coasting test method
GB/T 12543 vehicle acceleration performance test method
GB/T 12544 Test method for maximum speed cars
GB/T 12545.2 commercial vehicle fuel consumption test method
GB/T 12547 car lowest steady speed test method
GB/T 12673 Automotive main dimensions measuring method
GB/T 12674 Automotive Quality (by weight) parameter measurement method
GB/T 12677 technical condition of vehicle inspection method with
GB/T 12678 Automotive Reliability with Test Method
GB 18285 ignition engine exhaust emission limits and measurement methods (two-speed idle conditions and simple method)
GB 20891 non-road mobile machinery diesel engine exhaust emission limits and measurement methods (China third and fourth stage)
GB/T 50087 Industrial Enterprise Noise Control Design Specification
JB/T 5943 construction machinery welding parts General technical requirements
QC/T 413 automotive electrical equipment basic technical conditions
QC/T 484 car paint coating
QC/T 625 automotive and chemical process for coating layer
IATA AHM910 basic requirements for aviation ground support equipment (Basic requirements for aircraft ground support equipment)
IATA AHM915 standard control unit (Standard controls)
......
This preview omits tables, figures, formulas and parts of the technical clauses. The complete document — 15 pages — is available in the English PDF.
Referenced standards
Normative references
- GB 1495Limits and measurement methods for noise emitted by accelerating motor vehicles
- GB/T 3766Hydraulic fluid power -- General rules and safety requirements for systems and their components
- GB 4785Prescription for installation of the external lighting and light-signalling devices for motor vehicles and their trailers
- GB 7258Technical specifications for safety of power-driven vehicles operating on roads
- GB/T 7935Hydraulic fluid power - General requirements for hydraulic components
- GB/T 9969General principles for preparation of instructions for use of industrial products
Similar standards
How to Download GB/T 31029-2014
- 1
Add to cart
Click "Download PDF" on this page and choose "Buy this standard". You can add more standards before checkout.
- 2
Checkout
Enter your email and billing details. Payment is processed securely by Stripe (cards or bank transfer). Prefer bank details? Request a quotation (min. order $300).
- 3
Instant delivery (0–9 sec)
Delivery is automatic: within seconds of payment you'll receive an email with a secure download link. The link stays valid for 72 hours.
- 4
Invoice included
A tax invoice is attached to the confirmation email. Need a custom invoice? Contact us.
Related Standards
GB 1495-2002 — Limits and measurement methods for noise emitted by accelerating motor vehicles
GB 18285-2018 — Limits and measurement methods for emissions from gasoline vehicles under two-speed idle conditions and short driving mode conditions
GB 20891-2014 — [Including 2020XG1] Limits and measurement methods for exhaust pollutants from diesel engines of non-road mobile machinery (CHINA III, IV)
Secure payment via Stripe
Payments accepted
GB/T 31029-2014
$235.00