Valid

GB/T 12418-2025Technical requirements of repairs for steel general purpose containers (English PDF)

钢制通用集装箱修理技术要求

Preview PDF

This is a limited preview

Buy now to download the full PDF (33 pages)

Need quotation for your management?

Get a formal quotation for GB/T 12418-2025 in 30 minutes.

Issued by

State Administration for Market Regulation; Standardization Administration of China

Level / Type

National · Recommended

Issue date

October 31, 2025

Implementation date

May 1, 2026

Scope

GB/T 12418-2025 is the English-translated version of 钢制通用集装箱修理技术要求.

GB/T 12418-2025 is the Chinese standard "Technical requirements of repairs for steel general purpose containers". Its scope clause reads: This document specifies the technical requirements for the inspection and repair of steel general-purpose containers.

This document applies to the inspection and repair of general-purpose steel containers conforming to GB/T 1413 and GB/T 35201.Other types of containers... Packing instructions are as follows. Its clauses include terms and definitions.

Found what you need?

Document preview — GB/T 12418-2025

National Standard of the People's Republic of China

ICS: 55.180.10
Classification: A85

Issued by: State Administration for Market Regulation; Standardization Administration of China

Preface
1.Scope
2 Normative References
3.Terms and Definitions
4.Inspection
5 repair
Appendix A (Normative) Names and Codes of Major Components
Appendix B (Normative) Typical Damage Types and Their Codes
Appendix C (Normative) Main Repair Measures and Their Codes
Appendix D (Normative) Main Repair Materials and Their Codes
References

1 Scope

This document specifies the technical requirements for the inspection and repair of steel general-purpose containers.

This document applies to the inspection and repair of general-purpose steel containers conforming to GB/T 1413 and GB/T 35201.Other types of containers...

Packing instructions are as follows.

2 Normative references

The contents of the following documents, through normative references within the text, constitute essential provisions of this document. Dated citations are not included.

For references to documents, only the version corresponding to that date applies to this document; for undated references, the latest version (including all amendments) applies.

This document.

GB/T 1413 Series 1 Container Classification, Dimensions and Rated Mass

GB/T 1835 Series 1 Technical Requirements for Container Corner Fittings

GB/T 1836 Container Codes, Identification and Marking

GB/T 1992 Container Terminology

GB/T 20878-2024 Stainless Steel Grades and Chemical Composition

GB/T 35201 Series 2 Container Classification, Dimensions and Rated Mass

JT/T 1477 Series 2 Container Corner Fittings

3 Terms and Definitions

The terms and definitions defined in GB/T 1992 and the following terms and definitions apply to this document.

3.1 Inspection

Verification of the container's condition and suitability.

3.2 repair

Replacement or partial repair of container structural components, accessories, and materials to restore the container to normal operating condition and extend its service life.

Repair and shape correction work.

3.3 Refurbishment

Treatment of the inner and outer surfaces of containers, including painting and updating of markings.

3.4

According to the procedures established or approved by the competent authority, containers approved under the 1972 International Convention for the Safety of Containers shall be deemed suitable for operation.

The interval between conditions for inspecting or arranging inspections of containers.

3.5

As an alternative to periodic inspections, container inspections, approved by the competent authority or its authorized inspection agencies and formulated and implemented by the container owner, are permitted.

......
This preview omits tables, figures, formulas and parts of the technical clauses. The complete document — 33 pages — is available in the English PDF.

Referenced standards

Normative references

Cited by

Similar standards

GB/T 10819-2025|GB 13042-2008|GB 18191-2008|GB 19160-2008|GB 19269-2009

Editions of GB/T 12418

Edition	Title	Revision	Status
GB/T 12418-2025	Technical requirements of repairs for steel general purpose containers	current edition	Current
GB/T 12418-2001	The technical requirements of repairs for steel general purpose containers	previous edition	Superseded

This page sells the current edition, GB/T 12418-2025. Earlier editions are listed for reference only.

How to Download GB/T 12418-2025

1
Add to cart
Click "Download PDF" on this page and choose "Buy this standard". You can add more standards before checkout.
2
Checkout
Enter your email and billing details. Payment is processed securely by Stripe (cards or bank transfer). Prefer bank details? Request a quotation (min. order $300).
3
Instant delivery (0–9 sec)
Delivery is automatic: within seconds of payment you'll receive an email with a secure download link. The link stays valid for 72 hours.
4
Invoice included
A tax invoice is attached to the confirmation email. Need a custom invoice? Contact us.