Valid

JB/T 7359-2007Linear motion rolling bearings - Needle roller and flat cage assemblies (English PDF)

直线运动滚动支承 滚针和平保持架组件

Preview PDF

This is a limited preview

Buy now to download the full PDF (15 pages)

Need quotation for your management?

Get a formal quotation for JB/T 7359-2007 in 30 minutes.

Issued by

MIIT

Level / Type

Industry · Recommended

Issue date

March 6, 2007

Implementation date

March 6, 2007

Scope

JB/T 7359-2007 is the English-translated version of 直线运动滚动支承 滚针和平保持架组件.

JB/T 7359-2007 is the Chinese standard "Linear motion rolling bearings - Needle roller and flat cage assemblies".

Its scope clause reads: This standard specifies the structural types, designation methods, boundary dimensions and technical conditions of needle roller (including cylindrical roller) and cage assemblies (hereinafter referred to as “assemblies”) in linear motion rolling bearings.

This standard is applicable to the production, inspection and customer acceptance of assemblies. Its clauses include symbols; designation methods and structural types.

Found what you need?

Document preview — JB/T 7359-2007

National Standard of the People's Republic of China

ICS
21.100.20
Replacing
JB/T 7359-1994

Issued by: Ministry of Industry and Information Technology of the People's Republic of China

Contents

  • Foreword
  • 1 Scope
  • 2 Normative References
  • 3 Symbols
  • 4 Designation Methods and Structural Types
  • 4.1 Designation Methods
  • 4.2 Structural Types
  • 5 Boundary Dimensions
  • 6 Technical Requirements
  • 6.1 Material and Heat Treatment
  • 6.2 Tolerance
  • 6.3 Appearance
  • 6.4 Flexibility
  • 6.5 Others
  • 7 Measurement Methods
  • 7.1 Tolerances
  • 7.2 Rotating Flexibility
  • 8 Inspection Rules
  • 9 Marking
  • 10 Packaging and Storage
  • 11 Technical Requirements for Assembly-associated Parts
  • Appendix A (Informative) Technical Requirements for Assembly-associated Parts

1 Scope

This standard specifies the structural types, designation methods, boundary dimensions and technical conditions of needle roller (including cylindrical roller) and cage assemblies (hereinafter referred to as “assemblies”) in linear motion rolling bearings.

This standard is applicable to the production, inspection and customer acceptance of assemblies.

2 Normative References

The following standards contain provisions which, through reference in this text, constitute provisions of this national standard. For dated reference, subsequent amendments to (excluding the corrections to), or revisions of, any of these publications do not apply. However, parties to agreements based on this standard are encouraged to investigate the possibility of applying the most recent editions of the standards indicated below. For undated references, the latest edition of the normative document referred to applies.

GB/T 8597-2003 Rolling Bearings-Rust Proof Packaging

GB/T 18254-2002 High-carbon Chromium Bearing Steel

GB/T 13237-1991 Cold-rolled Quality Carbon Structural Steel Sheets and Strips

JB/T 1255-2001 Specification for Heat-treatment of Rolling Bearing Parts Made from High Carbon Chromium Steel

JB/T 3574-1997 Rolling Bearings-Marking for Products

JB/T 8921-1999 Rolling Bearings and Commercial Parts - Inspection Rules

JB/T 10335-2002 Linear Motion Rolling Bearings-Classification and Designation

3 Symbols

Unless otherwise stated, the symbols shown in figures (excluding tolerance symbols) and the values given in the tables denote nominal dimensions.

B: Width of assembly;

Dw: Diameter of needle roller (cylindrical roller) in assembly;

L: Length of assembly;

b: The distance from one end of the assembly to anther end of the needle roller in the horizontal section of V-type assembly;

VDwsp: The diameter variation of needle roller (cylindrical roller) in single plane in the assembly;

VDwL: The diameter variation of a batch of needle rollers (cylindrical rollers) in assembly;

*Dwmp: The average diameter deviation of needle roller (cylindrical roller) in single plane in the assembly .

4 Designation Methods and Structural Types

4.1 Designation Methods

Designations of assemblies listed in this standard and their and meanings are detailed in JB/T 10335-2002.

4.2 Structural Types

This standard specifies two structural types of assemblies:

LNS...NC Single row needle roller (cylindrical roller) and cage flat assemblies (see Figure 1);

LNS...NCW Double row needle roller (cylindrical roller) and cage V-type assemblies (see Figure 2).

......
This preview omits tables, figures, formulas and parts of the technical clauses. The complete document — 15 pages — is available in the English PDF.

Referenced standards

Similar standards

Editions of JB/T 7359

EditionTitleRevisionStatus
JB/T 7359-2007Linear motion rolling bearings - Needle roller and flat cage assembliescurrent editionCurrent
JB/T 7359-1994Linear motion rolling bearings - Needle roller and flat cage assembliesprevious editionSuperseded

This page sells the current edition, JB/T 7359-2007. Earlier editions are listed for reference only.

How to Download JB/T 7359-2007

  1. 1

    Add to cart

    Click "Download PDF" on this page and choose "Buy this standard". You can add more standards before checkout.

  2. 2

    Checkout

    Enter your email and billing details. Payment is processed securely by Stripe (cards or bank transfer). Prefer bank details? Request a quotation (min. order $300).

  3. 3

    Fast delivery

    After payment you'll receive an email confirmation. The English PDF is sent to the same address, usually within minutes and at the latest within 1 business day.

  4. 4

    Invoice included

    A tax invoice is attached to the confirmation email. Need a custom invoice? Contact us.

Related Standards

English PDF
15 pages
Fast delivery
Invoice included
View Cart

Secure payment via Stripe

Payments accepted

VisaMastercardAmerican ExpressApple PayGoogle PayStripe

JB/T 7359-2007

$55.00