Valid

JB/T 6364-2005Linear motion rolling bearings - Recirculating needle roller and roller guide bearings (English PDF)

直线运动滚动支承 循环式滚针、滚子导轨支承

Preview PDF

This is a limited preview

Buy now to download the full PDF (15 pages)

Need quotation for your management?

Get a formal quotation for JB/T 6364-2005 in 30 minutes.

Issued by

MIIT

Level / Type

Industry · Recommended

Issue date

May 24, 2005

Implementation date

November 1, 2005

Scope

JB/T 6364-2005 is the English-translated version of 直线运动滚动支承 循环式滚针、滚子导轨支承.

JB/T 6364-2005 is the Chinese standard "Linear motion rolling bearings - Recirculating needle roller and roller guide bearings".

Its scope clause reads: This standard specifies the structural types, boundary dimensions, tolerances and technical conditions for block type recirculating needle roller bearings and recirculating roller bearings among the linear motion rolling bearings.

This standard is applicable to the manufacture, inspection and acceptance of block type recirculating needle roller (or roller) bearings (hereinafter referred to as “guide bearings”). Its clauses include symbols.

Found what you need?

Document preview — JB/T 6364-2005

National Standard of the People's Republic of China

Replacing
JB/T 6364-1992

Issued by: Ministry of Industry and Information Technology of the People's Republic of China

Contents

  • Foreword I
  • 1 Scope
  • 2 Normative References
  • 3 Symbols
  • 4 Designation Methods
  • 5 Boundary Dimensions
  • 6 Technical Requirements
  • 6.1 Material
  • 6.2 Tolerance of guide bearing
  • 6.3 Surface Roughness
  • 6.4 Appearance Quality
  • 6.5 Flexibility
  • 6.6 Interchangeability
  • 7 Test Methods
  • 7.1 Surface Roughness
  • 7.2 Measurement of deltaAs, deltaAmL and VAmL
  • 7.3 Measurement of VAs
  • 8 Inspection Rules
  • 9 Marking
  • 10 Rust Prevention, Packaging and Storage
  • Figure 1 Block Type Recirculating Needle Roller Bearing LNS...RN Type
  • Figure 2 Recirculating Groove Needle Roller Bearing with Drawn Housing LNS...GRN Type
  • Figure 3 Recirculating Groove Needle Roller Bearing with End Head LNS...GRNU Type
  • Figure 4 Recirculating Roller Bearing with Radial Mounting Hole LRS...SG Type
  • Figure 5 Recirculating Roller Bearing with Axial Mounting Hole LRS...SGK Type
  • Figure 6 Diagram of Measurement Principle
  • Table 1 LNS...RN Type
  • Table 2 LNS...GRN Type
  • Table 3 LNS...GRNU Type
  • Table 4 LRS...SG and LRS...SGK Types
  • Table 5 Tolerances of Guide Bearings
  • Table 6 Inspection Items

1 Scope

This standard specifies the structural types, boundary dimensions, tolerances and technical conditions for block type recirculating needle roller bearings and recirculating roller bearings among the linear motion rolling bearings.

This standard is applicable to the manufacture, inspection and acceptance of block type recirculating needle roller (or roller) bearings (hereinafter referred to as “guide bearings”).

2 Normative References

The following standards contain provisions which, through reference in this text, constitute provisions of this national standard. For dated reference, subsequent amendments (excluding corrections) to, or revisions of, any of these publications do not apply. However, all parties coming to an agreement according to this standard are encouraged to study whether the latest edition of these documents applies. For undated references, the latest edition of the normative document referred to applies.

GB/T 1804-2000 General Tolerances-Tolerances for Linear and Angular Dimensions without Individual Tolerance Indications (eqv ISO 2768-1: 1989)

GB/T 4199-2003 Rolling Bearings-Tolerances-Definitions (ISO 1132-1: 2000, MOD)

GB/T 8597-2003 Rolling Bearings-Rust Proof Packaging

GB/T 13237-1991 Cold-rolled Quality Carbon Structural Steel Sheets and Strips

GB/T 18254-2002 High-carbon Chromium Bearing Steel

JB/T 1255-2001 JB/T 1255 -2001 Specification for Heat-treatment of Rolling Bearing Parts Made from High Carbon Chromium Steel

JB/T 3574-1997 Rolling Bearings-Marking for Products

JB/T 7051-1993 Rolling Bearings Parts-Methods for the Measurement and Assessment of Surface Roughness

JB/T 8921-1999 Rolling Bearings and Commercial Parts-Inspection Rules

JB/T 10335 - 2002 Linear Motion Rolling Bearings-Classification and Designation

3 Symbols

For the purpose of this standard, symbols specified in GB/T 4199 and the following ones apply.

Unless otherwise stated, all dimensions given in Table 1~Table 4 corresponding to the symbols shown in Figure 1~ Figure 5 denote nominal dimensions.

A: The height from the guide bearing rolling surface (the surface formed by contacting with the guide bearing rolling element) to the mounting reference face.

B: The width of guide bearing

B1: The width of mounting side-ear of needle roller bearing in the axial direction of needle roller h: The thickness of mounting side-ear of guide bearing

J: The distance between two mounting holes of guide bearing in axial direction of needle roller (roller)

J1: The distance between two mounting holes in motion direction of guide bearing

L: The length of guide bearing

L1: The length of mounting side-ear of needle roller bearing

L2: The length of supporting element of roller bearing

Lw: The roller length of roller bearing

N: The diameter of guide bearing mounting hole

T: The height of guide bearing (for guide bearing without mounting side-ear, T=A)

T1: The distance from the mounting hole axis of roller bearing to the bearing reference face

delta: The distance of needle roller (roller) protruding out of housing of guide bearing

VAmL: The grouping variation of guide bearing height, namely, in the group of same height, the difference between the guide bearing with highest average height from the guide bearing rolling surface to the mounting reference face and the guide bearing with lowest average height

VAs: The variation of height from the guide bearing rolling surface to the mounting reference face

deltaAs: The deviation of height from the guide bearing rolling surface (the surface formed by contacting with the guide bearing, the same bellow) to the mounting reference face (for LRS 0000 SGK type, it is the bearing reference face, the same bellow)

deltaAmL: The variation of preferentially grouped average height from the guide bearing rolling surface to the mounting reference face

deltaBs: The deviation of width of guide bearing

deltaB1s: The deviation of width of the mounting side-ear of needle roller bearing

deltaJs: The distance between two mounting holes in axial needle roller (roller) direction of guide bearing

deltaJ1s: The deviation of the distance between two mounting holes in motion direction of guide bearing

deltaL1s: The deviation of length of the mounting side-ear of needle roller bearing

deltaTs: The deviation of height of guide bearing

deltaT1s: The deviation of distance from the mounting hole axis of roller bearing to the bearing reference face

deltadeltas: The deviation of distance of needle roller (roller) protruding out of the housing of guide bearing […]

......
This preview omits tables, figures, formulas and parts of the technical clauses. The complete document — 15 pages — is available in the English PDF.

Similar standards

Editions of JB/T 6364

EditionTitleRevisionStatus
JB/T 6364-2005Linear motion rolling bearings - Recirculating needle roller and roller guide bearingscurrent editionCurrent
JB/T 6364-1992Linear motion rolling bearings - Recirculating needle roller and roller guide bearingsprevious editionSuperseded

This page sells the current edition, JB/T 6364-2005. Earlier editions are listed for reference only.

How to Download JB/T 6364-2005

  1. 1

    Add to cart

    Click "Download PDF" on this page and choose "Buy this standard". You can add more standards before checkout.

  2. 2

    Checkout

    Enter your email and billing details. Payment is processed securely by Stripe (cards or bank transfer). Prefer bank details? Request a quotation (min. order $300).

  3. 3

    Fast delivery

    After payment you'll receive an email confirmation. The English PDF is sent to the same address, usually within minutes and at the latest within 1 business day.

  4. 4

    Invoice included

    A tax invoice is attached to the confirmation email. Need a custom invoice? Contact us.

Related Standards

English PDF
15 pages
Fast delivery
Invoice included
View Cart

Secure payment via Stripe

Payments accepted

VisaMastercardAmerican ExpressApple PayGoogle PayStripe

JB/T 6364-2005

$85.00