JB/T 5388-2010Rolling bearings - Sleeve type linear ball bearings - Specifications (English PDF)
滚动轴承 套筒型直线球轴承 技术条件
This is a limited preview
Buy now to download the full PDF (15 pages)
Need quotation for your management?
Get a formal quotation for JB/T 5388-2010 in 30 minutes.
Issued by
MIIT
Level / Type
Industry · Recommended
Issue date
February 11, 2010
Implementation date
July 1, 2010
Scope
JB/T 5388-2010 is the English-translated version of 滚动轴承 套筒型直线球轴承 技术条件.
JB/T 5388-2010 is the Chinese standard "Rolling bearings - Sleeve type linear ball bearings - Specifications".
Its scope clause reads: This standard specifies the technical requirements, measurement methods, inspection rules, marking, rust prevention and packaging of sleeve type recirculating ball linear ball bearings (hereinafter referred to as "bearings") with ball set bore diameter of 4 mm ~150 mm.
This standard is applicable to the production, inspection and customer acceptance of sleeve type recirculating ball linear ball bearings.
Found what you need?
Document preview — JB/T 5388-2010
National Standard of the People's Republic of China
- ICS
- 21.100.20
- Replacing
- JB/T 5388-1999
Issued by: Ministry of Industry and Information Technology of the People's Republic of China
Contents
- Foreword
- 1 Scope
- 2 Normative References
- 3 Symbols
- 4 Technical Requirements
- 4.1 Material and Heat Treatment
- 4.2 Surface Roughness of Outer Ring
- 4.3 Tolerance
- 4.4 Residual Magnetism
- 4.5 Flexibility
- 4.6 Others
- 5 Measurement Methods
- 5.1 Surface Roughness
- 5.2 Tolerance
- 5.3 Residual Magnetism
- 5.4 Flexibility
- 6 Inspection Rules
- 7 Marking, Rust Prevention and Packaging
- 7.1 Marking
- 7.2 Rust Prevention and Packaging
- Appendix A (Normative) General Requirements of Mandrel and Ring Gauge for Inspection
1 Scope
This standard specifies the technical requirements, measurement methods, inspection rules, marking, rust prevention and packaging of sleeve type recirculating ball linear ball bearings (hereinafter referred to as "bearings") with ball set bore diameter of 4 mm ~150 mm.
This standard is applicable to the production, inspection and customer acceptance of sleeve type recirculating ball linear ball bearings.
2 Normative References
The following documents contain provisions which, through reference in this standard, constitute provisions of this standard. For dated reference, subsequent amendments to (excluding corrections to), or revisions of, any of these publications do not apply. However, the parties to agreements based on this standard are encouraged to investigate the possibility of applying the most recent editions of the standards. For undated references, the latest edition of the normative document referred to applies.
GB/T 307.3-2005 Rolling Bearings-General Technical Regulations
GB/T 2828.1-2003 Sampling Procedures for Inspection by Attributea – Part 1: Sampling Schemes Indexed by Acceptance Quality Limit (AQL) for Lot-by-lot Inspection (ISO 2859-1:1999; IDT)
GB/T 4199-2003 Rolling Bearings-Tolerances-Definitions (ISO 1132-1: 2000, Rolling bearings-Tolerances-Part 1: Terms and definitions, MOD)
GB/T 8597-2003 Rolling Bearings-Rust Proof Packaging
GB/T 16940-1997 Linear Motion Bearings-Linear Motion Ball Bearings-Boundary Dimensions and Tolerances (eqv ISO 10285:1992)
GB/T 18254-2002 High-carbon Chromium Bearing Steel
JB/T 1255 -2001 Specification for Heat-treatment of Rolling Bearing Parts Made from High Carbon Chromium Steel
JB/T 3574-1997 Rolling Bearings-Marking for Products
JB/T 6641-2007 Rolling Bearings-Residual Magnetism and Its Assessment Method
JB/T 7051-2006 Rolling Bearing Parts-Methods for the Measurement and Assessment of Surface Roughness […]
......
This preview omits tables, figures, formulas and parts of the technical clauses. The complete document — 15 pages — is available in the English PDF.
Referenced standards
Normative references
- GB/T 307.3-2005Rolling bearings - General technical regulations
- GB/T 2828.1-2003Sampling procedures for inspection by attributes - Part 1: Sampling schemes indexed by acceptance quality limit (AQL) for lot-by-lot inspection
- GB/T 4199-2003Rolling bearings -- Tolerances -- Definitions
- GB/T 8597-2003Rolling bearings - Rust proof packaging
- GB/T 16940-1997Rolling bearings -- Sleeve type linear ball bearings -- Boundary dimensions and tolerances
- GB/T 18254-2002High-carbon chromium bearing steel
Similar standards
Editions of JB/T 5388
| Edition | Title | Revision | Status |
|---|---|---|---|
| JB/T 5388-2010 | Rolling bearings - Sleeve type linear ball bearings - Specifications | current edition | Current |
| JB/T 5388-1999 | Rolling bearings - Sleeve type linear ball bearings - Specifications | previous edition | Superseded |
This page sells the current edition, JB/T 5388-2010. Earlier editions are listed for reference only.
How to Download JB/T 5388-2010
- 1
Add to cart
Click "Download PDF" on this page and choose "Buy this standard". You can add more standards before checkout.
- 2
Checkout
Enter your email and billing details. Payment is processed securely by Stripe (cards or bank transfer). Prefer bank details? Request a quotation (min. order $300).
- 3
Instant delivery (0–9 sec)
Delivery is automatic: within seconds of payment you'll receive an email with a secure download link. The link stays valid for 72 hours.
- 4
Invoice included
A tax invoice is attached to the confirmation email. Need a custom invoice? Contact us.
Related Standards
GB/T 4199-2003 — Rolling bearings -- Tolerances -- Definitions
JB/T 1255-2001 — Technical requirements for heat treatment of rolling bearing parts made of high-carbon chromium bearing steel
JB/T 3574-1997 — Rolling bearings - Product marking
Secure payment via Stripe
Payments accepted
JB/T 5388-2010
$189.00