JB/T 4712.4-2007Vessel supports - Part 4: Bracket supports (English PDF)
容器支座 第4部分 支承式支座
This is a limited preview
Buy now to download the full PDF (16 pages)
Need quotation for your management?
Get a formal quotation for JB/T 4712.4-2007 in 30 minutes.
Issued by
MIIT
Level / Type
Industry · Recommended
Issue date
August 28, 2007
Implementation date
February 1, 2008
Scope
JB/T 4712.4-2007 is the English-translated version of 容器支座 第4部分 支承式支座.
JB/T 4712.4-2007 is the Chinese standard "Vessel supports - Part 4: Bracket supports". Its scope clause reads: This Part specifies the structural types, series parameters and dimensions, permissible loads, materials, manufacture and inspection requirements and selection methods of the bracket supports.
This Part is applicable to the vertical cylindrical steel vessels under the following conditions. a) Nominal diameter DN 800mm~4000mm; b) Ratio of cylinder length L to nominal diameter DN DN<=5; c) Total height of vessel H0<=10m.
Found what you need?
Document preview — JB/T 4712.4-2007
National Standard of the People's Republic of China
- Replacing
- JB/T 4724-1992
Issued by: Ministry of Industry and Information Technology of the People's Republic of China
Contents
- Foreword i
- 1 Scope
- 2 Normative References
- 3 Type Characteristics
- 4 Series Parameters and Dimensions
- 5 Materials
- 6 Marking
- 7 Manufacturing Technology Requirements
- 8 Selection
- Appendix A (Informative) Approximate Calculation of Actual Bearing Load of Bracket Support
- Appendix B (Informative) Permissible Vertical Loads [F] of Type B Supports Restricted by the Vessel Heads
- Appendix C (Informative) Installation Height of Bracket Support
1 Scope
1.1
This Part specifies the structural types, series parameters and dimensions, permissible loads, materials, manufacture and inspection requirements and selection methods of the bracket supports.
1.2
This Part is applicable to the vertical cylindrical steel vessels under the following conditions.
a) Nominal diameter DN 800mm~4000mm;
b) Ratio of cylinder length L to nominal diameter DN DN<=5;
c) Total height of vessel H0<=10m.
2 Normative References
The following standards contain provisions which, through reference in this text, constitute provisions of this Part of JB/T 4712. For dated reference, subsequent amendments to (excluding correction to), or revisions of, any of these publications do not apply. However, the parties to agreements based on this standard are encouraged to investigate the possibility of applying the most recent editions of the standards. For undated references, the latest edition of the normative document referred to applies.
GB/T 985 Basic forms and sizes of weld grooves for gas welding, manual arc welding and gas-shielded arc welding
GB/T 1804 General tolerances-tolerances for linear and angular dimensions without individual tolerance indications […]
......
This preview omits tables, figures, formulas and parts of the technical clauses. The complete document — 16 pages — is available in the English PDF.
Referenced standards
Cited by
- GB/T 25027-2018Structure, main size and basic parameters of two pieces glass-lined steel vessels with agitator
- GB/T 25026-2017Structure, main dimensions and basic parameters of one-piece glass-lined steel vessels with agitator
- JB/T 8867-2015Stationary reciprocating piston air compressors - Air receivers
- GB/T 25027-2010Two pieces glass-lined steel vessels with agitator
Similar standards
Editions of JB/T 4712.4
| Edition | Title | Revision | Status |
|---|---|---|---|
| JB/T 4712.4-2007 | Vessel supports - Part 4: Bracket supports | current edition | Current |
| JB/T 4724-1992 | Vessel supports - Part 4: Bracket supports | previous edition | Superseded |
This page sells the current edition, JB/T 4712.4-2007. Earlier editions are listed for reference only.
How to Download JB/T 4712.4-2007
- 1
Add to cart
Click "Download PDF" on this page and choose "Buy this standard". You can add more standards before checkout.
- 2
Checkout
Enter your email and billing details. Payment is processed securely by Stripe (cards or bank transfer). Prefer bank details? Request a quotation (min. order $300).
- 3
Fast delivery
After payment you'll receive an email confirmation. The English PDF is sent to the same address, usually within minutes and at the latest within 1 business day.
- 4
Invoice included
A tax invoice is attached to the confirmation email. Need a custom invoice? Contact us.
Related Standards
JB/T 4712.4-2007
$168.00