JB/T 4712.1-2007Vessel supports - Part 1: Saddle supports (English PDF)
容器支座 第1部分 鞍式支座
This is a limited preview
Buy now to download the full PDF (25 pages)
Need quotation for your management?
Get a formal quotation for JB/T 4712.1-2007 in 30 minutes.
Issued by
MIIT
Level / Type
Industry · Recommended
Issue date
August 28, 2007
Implementation date
February 1, 2008
Scope
JB/T 4712.1-2007 is the English-translated version of 容器支座 第1部分 鞍式支座.
JB/T 4712.1-2007 is the Chinese standard "Vessel supports - Part 1: Saddle supports". Its scope clause reads: This Part specifies the structural types, series parameters and dimensions, permissible loads, materials, as well as manufacture, inspection, acceptance and installation technical requirements of the saddle supports.
This Part is applicable to the saddle supports of steel horizontal vessels supported by two points. As for the saddle supports of steel horizontal vessels supported by several points, their structural types and dimensions may make reference to this standard.
Design conditions of saddle supports in this Part: a) Design temperature : 200°C; b) Seismic intensity: Intensity 8 (Category II site soil). Its clauses include type characteristics.
Found what you need?
Document preview — JB/T 4712.1-2007
National Standard of the People's Republic of China
- Replacing
- JB/T 4712-1992
Issued by: Ministry of Industry and Information Technology of the People's Republic of China
Contents
- Foreword i
- 1 Scope
- 2 Normative References
- 3 Type Characteristics
- 4 Series Parameters and Dimensions
- 5 Materials
- 6 Marking
- 7 Manufacturing Technology Requirements
- 8 Selection
- Appendix A (Informative) Sliding Saddle Bolt Hole Length
- Appendix B (Informative) Permissible Loads of Saddle Support above Standard Height
- Appendix C (Informative) Saddle Support Bearing Plate Dimension
1 Scope
1.1
This Part specifies the structural types, series parameters and dimensions, permissible loads, materials, as well as manufacture, inspection, acceptance and installation technical requirements of the saddle supports.
1.2
This Part is applicable to the saddle supports of steel horizontal vessels supported by two points. As for the saddle supports of steel horizontal vessels supported by several points, their structural types and dimensions may make reference to this standard.
1.3
Design conditions of saddle supports in this Part:
a) Design temperature : 200°C;
b) Seismic intensity: Intensity 8 (Category II site soil).
2 Normative References
The following standards contain provisions which, through reference in this text, constitute provisions of this Part of JB/T 4712. For dated reference, subsequent amendments to (excluding correction to), or revisions of, any of these publications do not apply. However, the parties to agreements based on this standard are encouraged to investigate the possibility of applying the most recent editions of the standards. For undated references, the latest edition of the normative document referred to applies.
GB/T 985 Basic forms and sizes of weld grooves for gas welding, manual arc welding and gas-shielded arc welding
GB/T 1804 General tolerances-tolerances for linear and angular dimensions without individual tolerance indications
3 Type Characteristics
Saddle supports are divided into light-duty (code A) and heavy-duty (code B) ones.
Heavy-duty saddle supports are divided into five models according to the manufacture mode, wrap angle and attached subplate condition; structure characteristics of each model of saddle supports are detailed in Table 1.
......
This preview omits tables, figures, formulas and parts of the technical clauses. The complete document — 25 pages — is available in the English PDF.
Referenced standards
Cited by
- CJ/T 462-2014Direct pressurized water supply units
- NB/T 47042-2014Horizontal Vessels on Saddle Supports
- CJ/T 415-2013Non-negative pressure water supply equipment for water supply network booster pump station in cities and towns
- GB/T 26003-2010Non-negative pipe system pressure-increasing water supply equipment
Similar standards
Editions of JB/T 4712.1
| Edition | Title | Revision | Status |
|---|---|---|---|
| JB/T 4712.1-2007 | Vessel supports - Part 1: Saddle supports | current edition | Current |
| JB/T 4712-1992 | Vessel supports - Part 1: Saddle supports | previous edition | Superseded |
This page sells the current edition, JB/T 4712.1-2007. Earlier editions are listed for reference only.
How to Download JB/T 4712.1-2007
- 1
Add to cart
Click "Download PDF" on this page and choose "Buy this standard". You can add more standards before checkout.
- 2
Checkout
Enter your email and billing details. Payment is processed securely by Stripe (cards or bank transfer). Prefer bank details? Request a quotation (min. order $300).
- 3
Fast delivery
After payment you'll receive an email confirmation. The English PDF is sent to the same address, usually within minutes and at the latest within 1 business day.
- 4
Invoice included
A tax invoice is attached to the confirmation email. Need a custom invoice? Contact us.
Related Standards
JB/T 4712.1-2007
$248.00