Valid

JB/T 4712.3-2007Vessel supports - Part 3: Lug supports (English PDF)

容器支座 第3部分 耳式支座

Preview PDF

This is a limited preview

Buy now to download the full PDF (33 pages)

Need quotation for your management?

Get a formal quotation for JB/T 4712.3-2007 in 30 minutes.

Issued by

MIIT

Level / Type

Industry · Recommended

Issue date

August 28, 2007

Implementation date

February 1, 2008

Scope

JB/T 4712.3-2007 is the English-translated version of 容器支座 第3部分 耳式支座.

JB/T 4712.3-2007 is the Chinese standard "Vessel supports - Part 3: Lug supports". Its scope clause reads: This Part specifies the structural types, series parameters and dimensions, permissible loads, materials, manufacture and inspection requirements and selection methods of the lug supports.

This Part is applicable to the vertical cylindrical vessels whose nominal diameter is not greater than 4000 mm. Its clauses include type characteristics; series parameters and dimensions; materials; marking; manufacturing requirements; selection.

Found what you need?

Document preview — JB/T 4712.3-2007

National Standard of the People's Republic of China

Replacing
JB/T 4725-1992

Issued by: Ministry of Industry and Information Technology of the People's Republic of China

Contents

  • Contents
  • Foreword i
  • 1 Scope
  • 2 Normative References
  • 3 Type Characteristics
  • 4 Series Parameters and Dimensions
  • 5 Materials
  • 6 Marking
  • 7 Manufacturing Requirements
  • 8 Selection
  • Appendix A (Informative) Approximate Calculation of Actual Bearing Load of Lug Support
  • Appendix B (Informative) Permissible Bending Moment of Support Restricted by the Vessel Enclosure
  • Appendix C (Informative) Installation Dimension of Lug Support

1 Scope

1.1

This Part specifies the structural types, series parameters and dimensions, permissible loads, materials, manufacture and inspection requirements and selection methods of the lug supports.

1.2

This Part is applicable to the vertical cylindrical vessels whose nominal diameter is not greater than 4000 mm.

2 Normative References

The following standards contain provisions which, through reference in this text, constitute provisions of this Part of JB/T 4712. For dated reference, subsequent amendments to (excluding correction to), or revisions of, any of these publications do not apply. However, the parties to agreements based on this standard are encouraged to investigate the possibility of applying the most recent editions of the standards. For undated references, the latest edition of the normative document referred to applies.

GB/T 985 Basic forms and sizes of weld grooves for gas welding, manual arc welding and gas-shielded arc welding

GB/T 1804 General tolerances-tolerances for linear and angular dimensions without individual tolerance indications

JB/T 4730.1-2005 Nondestructive testing of pressure equipments-Part 1: General requirements

JB/T 4730 2-2005 Nondestructive testing of pressure equipments-Part 2: Radiographic testing

JB/T 4730.3-2005 Nondestructive testing of pressure equipments-Part 3: Ultrasonic testing

JB/T 4730.4-2005 Nondestructive testing of pressure equipments-Part 4: Magnetic particle testing

JB/T 4730.5-2005 Nondestructive testing of pressure equipments-Part 5: Penetrant testing

JB/T 4730.6-2005 Nondestructive testing of pressure equipments-Part 6: Eddy current testing

3 Type Characteristics

Type characteristics of lug supports are detailed in Table 1.

Table 1 Type characteristics

Type Support number Subplate Cover plate Applicable nominal diameter DN mm Support dimension (See Figure and Table)

Short arm A 1~5 Some None 300~2600 Figure 1 Table 3

6~8 Some 1500~4000 Figure 2

Long arm B 1~5 Some None 300~2600 Figure 3 Table 4

6~8 Some 1500~4000 Figure 4

Extension arm C 1~3 Some Some 300~1400 Figure 5 Table 5

4~8 1000~4000 Figure 6

4 Series Parameters and Dimensions

4.1

Type A lug supports shall be in accordance with Figure 1, Figure 2 and Table 2; Type B lug supports shall be in accordance with Figure 3, Figure 4 and Table 3; Type C lug supports shall be in accordance with Figure 5, Figure 6 and Table 4.

4.2

The thickness support subplate shall meet the requirements of this Part. Generally, the thickness of support subplate is the same as that of the cylinder, which may also be determined according to the actual requirements.

5 Materials

5.1

Generally, subplate materials shall be the same as the vessel materials.

5.2

Materials of support rib plate and base plate are divided into 4 kinds, with the codes detailed in Table 2.

Table 2 Material code

Material code I II III IV Materials of support rib plate and base plate Q235A 16MnR 0Cr18Ni9 15CrMoR

Figure 1 Type A (support No. 1~5)

Figure 2 Type A (support No. 6~8)

Figure 3 Type B (support No. 1~5)

Figure 4 Type B (support No. 6~8)

Figure 5 Type C (support No. 1~3)

Figure 6 Type C (support No. 4~8)

Table 3 Series parameters and dimensions of Type A supports mm

Support number Permissible load of support

[Q], kN Nominal diameter of applicable vessel

DN Height

H Base plate Rib plate Subplate Cover plate Foundation bolt Support mass kg l1 b1 delta1 s1 l2 b2 delta2 l3 b3 delta3 e b4 delta4 d Specification

Q235A

0Cr18Ni9 16MnR

15CrMoR

1 10 14 300~600 125 100 60 6 30 80 70 4 160 125 6 20 30 - 24 M20 1.7

2 20 26 500~1000 160 125 80 8 40 100 90 5 200 160 6 24 30 - 24 M20 3.0

3 30 44 700~1400 200 160 105 10 50 125 110 6 250 200 8 30 30 - 30 M24 6.0

4 60 90 1000~2000 250 200 140 14 70 160 140 8 315 250 8 40 30 - 30 M24 11.1

5 100 120 1300~2600 320 250 180 16 90 200 180 10 400 320 10 48 30 - 30 M24 21.6

6 150 190 1500~3000 400 320 230 20 115 250 230 12 500 400 12 60 50 12 36 M30 42.7

7 200 230 1700~3400 480 375 280 22 130 300 280 14 600 480 14 70 50 14 36 M30 69.8

8 250 320 2000~4000 600 480 360 26 145 380 350 16 720 600 16 72 50 16 36 M30 123.9

Note: the support mass in this Table is calculated on the basis of thickness delta3 in this Table; the support mass will change with the delta3 thickness.

Table 4 Type B support series parameter list mm

Support number Permissible load of support

[Q], kN Nominal diameter of applicable vessel

DN Height

H Base plate Rib plate Subplate Cover plate Foundation bolt Support mass kg l1 b1 delta1 s1 l2 b2 delta2 l3 b3 delta3 e b4 delta4 d Specification

Q235A

0Cr18Ni9 16MnR

15CrMoR

1 10 14 300~600 125 100 60 6 30 160 70 5 160 125 6 20 50 - 24 M20 2.5

2 20 26 500~1000 160 125 80 8 40 180 90 6 200 160 6 24 50 - 24 M20 4.3

3 30 44 700~1400 200 160 105 10 50 205 110 8 250 200 8 30 50 - 30 M24 8.3

4 60 90 1000~2000 250 200 140 14 70 290 140 10 315 250 8 40 70 - 30 M24 15.7

5 100 120 1300~2600 320 250 180 16 90 330 180 12 400 320 10 48 70 - 30 M24 28.7

6 150 190 1500~3000 400 320 230 20 115 380 230 14 500 400 12 60 100 12 36 M30 53.9

7 200 230 1700~3400 480 375 280 22 130 430 270 16 600 480 14 70 100 14 36 M30 85.2

8 250 320 2000~4000 600 480 360 26 145 510 350 18 720 600 16 72 100 16 36 M30 146.0

Note: the support mass in this Table is calculated on the basis of thickness delta3 in this Table; the support mass will change with the delta3 thickness.

Table 5 Type C support series parameter list mm

Support number Permissible load of support

[Q], kN Nominal diameter of applicable vessel

DN Height

H Base plate Rib plate Subplate Cover plate Foundation bolt Support mass kg

Q235A

0Cr18Ni9 16MnR

15CrMoR l1 b1 delta1 s1 c l2 b2 delta2 l3 b3 delta3 e b4 delta4 d Specification

1 30 40 300~600 200 130 80 8 40 - 250 80 6 260 170 6 30 50 8 24 M

20 6.2

2 45 55 500~1000 250 160 80 12 40 - 280 100 6 310 210 6 30 50 10 30 M

24 9.0

3 65 85 700~1400 300 200 105 14 50 - 300 130 8 370 260 8 35 50 12 30 M

24 16.1

4 120 150 1000~2000 360 250 140 18 70 90 390 170 10 430 320 8 35 70 12 30 M

24 28.9

5 170 210 1300~2600 430 300 180 22 90 120 430 210 12 510 380 10 40 70 14 30 M

24 47.8

6 220 270 1500~3000 480 360 230 24 115 160 480 260 14 570 450 12 45 100 14 36 M

30 74.8

7 280 330 1700~3400 540 440 280 28 130 200 530 310 16 630 540 14 45 100 16 36 M

30 114.6

8 340 400 2000~4000 650 540 360 30 140 280 600 400 18 750 650 16 50 100 18 36 M

30 181.3

Note: the support mass in this Table is calculated on the basis of thickness delta3 in this Table; the support mass will change with the delta3 thickness.

6 Marking

6.1 Marking methods

JB/T 4712.3-2007, lug support X X - X

Note 1: if the subplate thickness delta3 is different from the normal dimension, it shall be noted in the parts names column or remarks column of equipment drawing: e.g. delta3= 12.

Note 2: support and subplate materials shall be filled in the material column of equipment drawing, representation method: support material/subplate material.

6.2 Marking examples

Example 1: Type A, No. 3 lug support, support material is Q235A, subplate material is Q235A:

JB/T 4712 3-2007, lug support A3-I

Material: Q235A

Example 2: Type B, No. 3 lug support, support material is 16MnR, subplate material is 0cr18Ni9, subplate thickness is 12mm:

JB/T 4712.3-2007, lug support B3-II, delta3=12

Material: 16MnR/0Cr18Ni9

7 Manufacturing Requirements

7.1

Arc welding shall be adopted; electrode designation shall be selected according to the support component materials with reference to the relevant standards. Types and dimensions of welded joints shall be in accordance with GB/T 985.

7.2

Lug support shall adopt double-side continuous fillet welding; support and vessel enclosure shall adopt continuous welding. Fillet weld dimension shall be about 0.7 times of the thickness of the relatively thin plate and shall not be less than 4mm.

7.3

Post-welding weld metal surfaces shall be free from any defect such as crack, slag inclusion, weld beading, burn through and arc crater; weld zone shall be free from splash.

7.4

Subplate shall fit closely with vessel wall; the maximum partial clearance shall be less than or equal to 1mm.

7.5

Processing limit deviation of support bolt holes and their spacing as well as manufacturing tolerance of other parts shall be respectively in accordance with the class m and class c precision in GB/T 1804.

7.6

Peripheral roughness of all the assembled and welded parts of the supports is Ra 50µm.

7.7

After the supports are assembled and welded, each component shall be flat, smooth and not warping.

7.8

If heat treatment is required on the vessel enclosure, support subplate shall be welded on the vessel wall before heat treatment.

8 Selection

8.1

Actual loads Q (kN) of lug supports shall be calculated according to the nominal diameter DN and the methods specified in Appendix A; a standard lug support shall be selected from the standard according to the actual load Q value, Q<=[Q].

8.2

Generally, the support bending moment ML of cylinder at the lug support shall be checked:

ML<=[ML]

As for the lined vessels:

Where,

ML - - Support bending moment of cylinder at the lug support, kN·m;

[ML] - - Permissible bending moment of cylinder at the lug support, see Appendix B, kN·m;

See Table 2, Table 3 and Table 4 for l2 and s1.

8.3

Generally, lug supports shall be arranged with subplates. When DN<=900mm, lug supports may not be arranged with subplates but must meet the following conditions:

a) Effective thickness of vessel enclosure shall be greater than 3mm;

b) Vessel enclosure materials shall have the same or similar chemical compositions and mechanical properties with the support materials.

8.4

Installation dimension D of supports may be calculated according to Appendix C.

......
This preview omits tables, figures, formulas and parts of the technical clauses. The complete document — 33 pages — is available in the English PDF.

Referenced standards

Similar standards

Editions of JB/T 4712.3

EditionTitleRevisionStatus
JB/T 4712.3-2007Vessel supports - Part 3: Lug supportscurrent editionCurrent
JB/T 4725-1992Vessel supports - Part 3: Lug supportsprevious editionSuperseded

This page sells the current edition, JB/T 4712.3-2007. Earlier editions are listed for reference only.

How to Download JB/T 4712.3-2007

  1. 1

    Add to cart

    Click "Download PDF" on this page and choose "Buy this standard". You can add more standards before checkout.

  2. 2

    Checkout

    Enter your email and billing details. Payment is processed securely by Stripe (cards or bank transfer). Prefer bank details? Request a quotation (min. order $300).

  3. 3

    Fast delivery

    After payment you'll receive an email confirmation. The English PDF is sent to the same address, usually within minutes and at the latest within 1 business day.

  4. 4

    Invoice included

    A tax invoice is attached to the confirmation email. Need a custom invoice? Contact us.

Related Standards

English PDF
33 pages
Fast delivery
Invoice included
View Cart

Secure payment via Stripe

Payments accepted

VisaMastercardAmerican ExpressApple PayGoogle PayStripe

JB/T 4712.3-2007

$348.00