Valid

JB/T 4712.2-2007Vessel supports - Part 2: Leg supports (English PDF)

容器支座 第2部分 腿式支座

Preview PDF

This is a limited preview

Buy now to download the full PDF (21 pages)

Need quotation for your management?

Get a formal quotation for JB/T 4712.2-2007 in 30 minutes.

Issued by

MIIT

Level / Type

Industry · Recommended

Issue date

August 28, 2007

Implementation date

February 1, 2008

Scope

JB/T 4712.2-2007 is the English-translated version of 容器支座 第2部分 腿式支座.

JB/T 4712.2-2007 is the Chinese standard "Vessel supports - Part 2: Leg supports".

Its scope clause reads: This Part specifies the structural types, series parameters and dimensions, permissible loads, materials, as well as manufacturing technology requirements of the leg supports (hereinafter referred to as supports) of the vertical steel vessels (hereinafter referred to as vessels).

This Part is applicable to the vessels directly installed on the rigid subgrade and meeting the following conditions: a) Nominal diameter is DN400mm~1600mm; b) Ratio of cylinder tangent length L to nominal diameter DN is not greater than 5; c) Total height of vessel H1: not greater than 5000mm for the angle strut and steel pipe strut; not greater than 8000mm for the H-shaped steel strut; d) Design temperature: t=200°C; e) Design wind velocity pressure: q0=800 Pa, ground roughness is Category A; f) Design seismic intensity: Intensity 8 (Category II site soil); design basic seismic acceleration: 0.2g.

This Part is not applicable to the vessels directly and rigidly connected with the machinery equipment generating pulsating loads through pipelines. Its clauses include type characteristics.

Found what you need?

Document preview — JB/T 4712.2-2007

National Standard of the People's Republic of China

Replacing
JB/T 4713-1992

Issued by: Ministry of Industry and Information Technology of the People's Republic of China

Contents

  • Contents
  • Foreword i
  • 1 Scope
  • 2 Normative References
  • 3 Type Characteristics
  • 4 Series Parameters and Dimensions
  • 5 Materials
  • 6 Marking
  • 7 Manufacturing Technology Requirements
  • 8 Selection
  • Appendix A (Informative) Support Calculation Method

1 Scope

1.1

This Part specifies the structural types, series parameters and dimensions, permissible loads, materials, as well as manufacturing technology requirements of the leg supports (hereinafter referred to as supports) of the vertical steel vessels (hereinafter referred to as vessels).

1.2

This Part is applicable to the vessels directly installed on the rigid subgrade and meeting the following conditions:

a) Nominal diameter is DN400mm~1600mm;

b) Ratio of cylinder tangent length L to nominal diameter DN is not greater than 5;

c) Total height of vessel H1: not greater than 5000mm for the angle strut and steel pipe strut; not greater than 8000mm for the H-shaped steel strut;

d) Design temperature: t=200°C;

e) Design wind velocity pressure: q0=800 Pa, ground roughness is Category A;

f) Design seismic intensity: Intensity 8 (Category II site soil); design basic seismic acceleration: 0.2g.

1.3

This Part is not applicable to the vessels directly and rigidly connected with the machinery equipment generating pulsating loads through pipelines.

2 Normative References

The following standards contain provisions which, through reference in this text, constitute provisions of this Part of JB/T 4712. For dated reference, subsequent amendments to (excluding correction to), or revisions of, any of these publications do not apply. However, the parties to agreements based on this standard are encouraged to investigate the possibility of applying the most recent editions of the standards. For undated references, the latest edition of the normative document referred to applies.

GB 150 Steel pressure vessels

GB/T 985 Basic forms and sizes of weld grooves for gas welding, manual arc welding and gas-shielded arc welding

GB/T 1804 General tolerances-tolerances for linear and angular dimensions without individual tolerance indications

GB/T 9787 Hot-rolled equal-leg angle steel-Dimensions, shape, weight and tolerances

GB/T 8163 Seamless steel tubes for liquid service

JB/T 4709 Welding Specification for Steel Pressure Vessels

YB 3301 The welded steel H-section

3 Type Characteristics

Type characteristics of leg supports are detailed in Table 1.

......
This preview omits tables, figures, formulas and parts of the technical clauses. The complete document — 21 pages — is available in the English PDF.

Similar standards

Editions of JB/T 4712.2

EditionTitleRevisionStatus
JB/T 4712.2-2007Vessel supports - Part 2: Leg supportscurrent editionCurrent
JB/T 4713-1992Vessel supports - Part 2: Leg supportsprevious editionSuperseded

This page sells the current edition, JB/T 4712.2-2007. Earlier editions are listed for reference only.

How to Download JB/T 4712.2-2007

  1. 1

    Add to cart

    Click "Download PDF" on this page and choose "Buy this standard". You can add more standards before checkout.

  2. 2

    Checkout

    Enter your email and billing details. Payment is processed securely by Stripe (cards or bank transfer). Prefer bank details? Request a quotation (min. order $300).

  3. 3

    Fast delivery

    After payment you'll receive an email confirmation. The English PDF is sent to the same address, usually within minutes and at the latest within 1 business day.

  4. 4

    Invoice included

    A tax invoice is attached to the confirmation email. Need a custom invoice? Contact us.

Related Standards

English PDF
21 pages
Fast delivery
Invoice included
View Cart

Secure payment via Stripe

Payments accepted

VisaMastercardAmerican ExpressApple PayGoogle PayStripe

JB/T 4712.2-2007

$208.00