Valid

JB/T 4278.1-1993Verification methods for test equipment for rubber and plastic insulated wires and cables - General (English PDF)

橡皮塑料电线电缆试验仪器设备检定方法 总则

Preview PDF

This is a limited preview

Buy now to download the full PDF (15 pages)

Need quotation for your management?

Get a formal quotation for JB/T 4278.1-1993 in 30 minutes.

Issued by

MIIT

Level / Type

Industry · Recommended

Issue date

January 1, 1993

Implementation date

January 1, 1993

Scope

JB/T 4278.1-1993 is the English-translated version of 橡皮塑料电线电缆试验仪器设备检定方法 总则.

JB/T 4278.1-1993 is the Chinese machinery industry standard covering verification methods for test equipment for rubber and plastic insulated wires and cables - General.

It was issued on 1 January 1993 and has been in force since 1 January 1993, as a first edition. The document is under the responsibility of the Ministry of Industry and Information Technology.

This page is published from the official record of the 1993 edition. The figures, limits and tables the standard contains are those of the document itself, delivered in full with the English translation.

Found what you need?

Document preview — JB/T 4278.1-1993

National Standard of the People's Republic of China

Issued by: Ministry of Industry and Information Technology of the People's Republic of China

Contents

  • [Preview only]
  • 1 Scope
  • 2 Normative references
  • 3 Terms and definitions
  • 3.1 Type
  • 3.2 Basic parameters
  • 4 Types and basic parameters
  • 4.1 Types
  • 4.2 Model designation
  • 4.3 Nominal operating conditions
  • 4.4 Safety and hygiene
  • 4.5 Welding
  • 4.6 Bridge (After crane operation mechanism assembled)
  • 4.7 Assembly
  • 4.8 Electrical control equipment
  • 4.9 Steel pretreatment and painting
  • 5 Technical requirements
  • 5.1 General requirements
  • 5.2 Safety requirements
  • 5.3 Cold and hot working forming
  • 5.4 Rated load test
  • 5.5 Whole machine noise test
  • 5.6 Static rigidity test
  • 5.7 Dynamic load test
  • 5.8 Crane span deviation
  • 5.9 Diagonal difference of bridge
  • 6 Test methods
  • 6.1 Exit-factory inspection
  • 6.2 Type inspection
  • 7 Inspection rules
  • 7.1 Marking
  • 7.2 Packaging, transportation and storage
  • 7.3 Transportation
  • 7.4 Storage
  • 8 Marking, packaging, transportation and storage
  • 9 标志和标签 9 Marking and labeling

1 Foreword

JB/T 4278.1-1993 is issued by Ministry of Industry and Information Technology of the People's Republic of China.

It is one of 28 parts of the JB/T 4278 series.

The JB/T prefix marks a recommended standard. It is not law in itself: it becomes binding when a contract names it, when a regulation or a mandatory standard refers to it, or when a producer declares conformity with it.

2 Scope Preview

JB/T 4278.1-1993 carries no ICS number and no Chinese Standard Classification code.

This catalogue holds 21,922 other JB/T standards.

Of the 5,298 JB/T standards that do carry an ICS number, 1,460 (28%) fall under ICS 25, in the field of manufacturing engineering.

3 About this standard

Issued by: Ministry of Industry and Information Technology of the People's Republic of China

English translation: about 15 pages

4 Related standards

Other parts of this standard:

JB/T 4278.2-1993 — Low temperature impact test apparatus

JB/T 4278.2-2011 — Verification procedure for test equipment of rubber plastic wire and cable - Part 2: Low temperature impact test device

JB/T 4278.3-1993 — Flexing test apparatus

JB/T 4278.3-2011 — Verification procedure for test equipment of rubber plastic wire and cable - Part 3: Flexing test device

JB/T 4278.4-1993 — Abrasion test apparatus

JB/T 4278.4-2011 — Verification procedure for test equipment of rubber plastic wire and cable - Part 4: Abrasion test device

JB/T 4278.5-1993 — DZ-1 test apparatus for vertical burning of single wires and cables

JB/T 4278.5-2011 — Verification procedure for test equipment of rubber plastic wire and cable - Part 5: Single insulated wire and cable vertical burning test device

JB/T 4278.6-1993 — Natural ventilation heat ageing test chambers

JB/T 4278.6-2011 — Verification procedure for test equipment of rubber plastic wire and cable - Part 6: Natural ventilation thermal aging test oven

JB/T 4278.7-1993 — Constant temperature water baths

JB/T 4278.7-2011 — Verification procedure for test equipment of rubber plastic wire and cable - Part 7: Thermostat water bath

JB/T 4278.8-1993 — Verification methods for test instruments and equipment for rubber and plastic insulated wires and cables - Low temperature test chambers

JB/T 4278.8-2011 — Verification procedure for test equipment of rubber plastic wire and cable - Part 8: Low temperature test oven

JB/T 4278.9-1993 — Oxygen bomb and air bomb ageing test chambers

JB/T 4278.9-2011 — Verification procedure for test equipment of rubber plastic wire and cable - Part 9: Oxygen bomb, air bomb aging test oven

JB/T 4278.10-1993 — Spark testers

JB/T 4278.10-2011 — Verification procedure for test equipment of rubber plastic wire and cable - Part 10: Spark tester

JB/T 4278.11-2011 — Verification procedure for test equipment of rubber and plastic wires and cables - Part 11: Low temperature bending test device

JB/T 4278.12-2011 — Verification procedure for test equipment of rubber plastic wire and cable - Part 12: High temperature pressure test device

JB/T 4278.13-2011 — Verification procedure for test equipment of rubber plastic wire and cable - Part 13: Forced air heat aging test oven

JB/T 4278.14-2011 — Verification procedure for test equipment of rubber plastic wire and cable - Part 14: Fire-resisting test device

JB/T 4278.15-2011 — Verification procedure for test equipment of rubber plastic wire and cable - Part 15: Bundle burning test device

JB/T 4278.16-2011 — Verification procedure for test equipment of rubber plastic wire and cable - Part 16: Smoke density test device

JB/T 4278.17-2011 — Verification procedure for test equipment of rubber plastic wire and cable - Part 17: Carbon black content test device

JB/T 4278.18-2011 — Verification procedure for test equipment of rubber plastic wire and cable - Part 18: Copper single insulated wire and cable vertical burning test device

JB/T 4278.19-2011 — Verification procedure for test equipment of rubber plastic wire and cable - Part 19: Insulation scrape abrasion test device

Other editions:

JB/T 4278.1-2011 (later edition)

5 Classification and status

Prefix JB/T: recommended standard.

......
This preview omits tables, figures, formulas and parts of the technical clauses. The complete document — 15 pages — is available in the English PDF.

Referenced standards

Cited by

Similar standards

How to Download JB/T 4278.1-1993

  1. 1

    Add to cart

    Click "Download PDF" on this page and choose "Buy this standard". You can add more standards before checkout.

  2. 2

    Checkout

    Enter your email and billing details. Payment is processed securely by Stripe (cards or bank transfer). Prefer bank details? Request a quotation (min. order $300).

  3. 3

    Fast delivery

    After payment you'll receive an email confirmation. The English PDF is sent to the same address, usually within minutes and at the latest within 1 business day.

  4. 4

    Invoice included

    A tax invoice is attached to the confirmation email. Need a custom invoice? Contact us.

Related Standards

English PDF
15 pages
Fast delivery
Invoice included
View Cart

Secure payment via Stripe

Payments accepted

VisaMastercardAmerican ExpressApple PayGoogle PayStripe

JB/T 4278.1-1993

$209.00