JB/T 4278.15-2011Verification procedure for test equipment of rubber plastic wire and cable - Part 15: Bundle burning test device (English PDF)

1 Foreword

JB/T 4278.15-2011 was issued by MIIT on 18 May 2011 and has been in force since 1 August 2011.

It is one of 29 parts of the JB/T 4278 series.

2 Scope

This standard is the part of the recommended Chinese machinery industry standard on verification procedures for rubber and plastic wire and cable test equipment that concerns the bundle burning test device. It states the verification items and the technical requirements for the unit, the apparatus used to make the checks, the test methods and the treatment of the results. It applies to burning test units that are newly manufactured, in use or put back into service after maintenance. The document is filed under Chinese classification K13 and international classification 29.060. It quotes JB/T 4278.1-2011.

3 Normative references

JB/T 4278.15-2011 cites the following standards, which apply in full or in part through the references made to them in its clauses.

JB/T 4278.1-2011 — Verification procedure for test equipment of rubber plastic wire and cable - Part 1: General

4 About this standard

Issued by: MIIT

English translation: about 15 pages

5 Related standards

Other parts of this standard:

JB/T 4278.1-1993 — Verification methods for test equipment for rubber and plastic insulated wires and cables - General

JB/T 4278.1-2011 — Part 1: General

JB/T 4278.2-1993 — Verification methods for test equipment for rubber and plastic insulated wires and cables - Low temperature impact test apparatus

JB/T 4278.2-2011 — Part 2: Low temperature impact test device

JB/T 4278.3-1993 — Verification methods for test equipment for rubber and plastic insulated wires and cables - Flexing test apparatus

JB/T 4278.3-2011 — Part 3: Flexing test device

JB/T 4278.4-1993 — Verification methods for test equipment for rubber and plastic insulated wires and cables - Abrasion test apparatus

JB/T 4278.4-2011 — Part 4: Abrasion test device

JB/T 4278.5-1993 — Verification methods for test equipment for rubber and plastic insulated wires and cables - DZ-1 test apparatus for vertical burning of single wires and cables

JB/T 4278.5-2011 — Part 5: Single insulated wire and cable vertical burning test device

JB/T 4278.6-1993 — Verification methods for test equipment for rubber and plastic insulated wires and cables - Natural ventilation heat ageing test chambers

JB/T 4278.6-2011 — Part 6: Natural ventilation thermal aging test oven

JB/T 4278.7-1993 — Verification methods for test equipment for rubber and plastic insulated wires and cables - Constant temperature water baths

JB/T 4278.7-2011 — Part 7: Thermostat water bath

JB/T 4278.8-1993 — Verification methods for test instruments and equipment for rubber and plastic insulated wires and cables - Low temperature test chambers

JB/T 4278.8-2011 — Part 8: Low temperature test oven

JB/T 4278.9-1993 — Verification methods for test equipment for rubber and plastic insulated wires and cables - Oxygen bomb and air bomb ageing test chambers

JB/T 4278.9-2011 — Part 9: Oxygen bomb, air bomb aging test oven

JB/T 4278.10-1993 — Verification methods for test equipment for rubber and plastic insulated wires and cables - Spark testers

JB/T 4278.10-2011 — Part 10: Spark tester

JB/T 4278.11-2011 — and plastic wires and cables - Part 11: Low temperature bending test device

JB/T 4278.12-2011 — Part 12: High temperature pressure test device

JB/T 4278.13-2011 — Part 13: Forced air heat aging test oven

JB/T 4278.14-2011 — Part 14: Fire-resisting test device

JB/T 4278.16-2011 — Part 16: Smoke density test device

JB/T 4278.17-2011 — Part 17: Carbon black content test device

JB/T 4278.18-2011 — Part 18: Copper single insulated wire and cable vertical burning test device

JB/T 4278.19-2011 — Part 19: Insulation scrape abrasion test device

6 Classification and status

International classification (ICS): 29.060

Prefix JB/T: recommended standard.