GB/T 7672.6-2008Glass-fiber wound winding wires - Part 6: Glass-fiber and film wound rectangular copper wire (English PDF)
玻璃丝包绕组线 第6部分：玻璃丝包薄膜绕包铜扁线
This is a limited preview
Buy now to download the full PDF (15 pages)
Need quotation for your management?
Get a formal quotation for GB/T 7672.6-2008 in 30 minutes.
Issued by
SAMR; SAC
Level / Type
National · Recommended
Issue date
June 30, 2008
Implementation date
May 1, 2009
Scope
GB/T 7672.6-2008 is the English-translated version of 玻璃丝包绕组线 第6部分：玻璃丝包薄膜绕包铜扁线.
GB/T 7672.6-2008 is the Chinese standard "Glass-fiber wound winding wires - Part 6: Glass-fiber and film wound rectangular copper wire". Its scope clause reads: GB/T 7672 provisions of this part of the impregnated, bare, copper-clad film wound flat wire requirements.
Impregnated, bare film about Shao Jie Copper flat wire package is not included within the scope of this section. --- Broadside size. minimum 2.00mm, maximum 16.00mm; --- Narrow size. minimum 0.80mm, maximum 5.60mm.
A combination of size and narrow broadside sizes and ratios see GB/T 7672.1-2008 provisions of. Its clauses include definitions, test methods and general appearance.
Found what you need?
Document preview — GB/T 7672.6-2008
National Standard of the People's Republic of China
- ICS
- 29.060.10
- Classification
- K 12
- Replacing
- GB/T 7672.6-1987
Issued by: State Administration for Market Regulation; Standardization Administration of the PRC
Contents
- 1 Scope
- 2 Normative references
- 3 Definitions, test methods and General Appearance
- 3.1 Overview
- 3.2 definitions
1 Scope
GB/T 7672 provisions of this part of the impregnated, bare, copper-clad film wound flat wire requirements. Impregnated, bare film about Shao Jie
Copper flat wire package is not included within the scope of this section.
--- Broadside size. minimum 2.00mm, maximum 16.00mm;
--- Narrow size. minimum 0.80mm, maximum 5.60mm.
A combination of size and narrow broadside sizes and ratios see GB/T 7672.1-2008 provisions of.
2 Normative references
The following documents contain provisions which, through GB/T reference in this 7672 constitute provisions of this part. For dated reference documents
Member, all subsequent amendments (not including errata content) or revisions do not apply to this section, however, encouraged to reach under this section
Parties to research agreement to use the latest versions of these documents. For undated reference documents, the latest versions apply to this section.
GB/T 4074.1 Winding wires test methods - Part 1. General requirements (GB/T 4074.1-2008, IEC 60851-1.1996,
IDT)
GB/T 4074.2 Winding wires test methods - Part 2. Measure (GB/T 4074.2-2008, IEC 60851-2.1997,
IDT)
GB/T 4074.3 Winding wires test methods - Part 3. Mechanical properties (GB/T 4074.3-2008, IEC 60851-3.1997,
IDT)
GB/T 4074.5-2008 Winding wires - Test methods - Part 5. Electrical properties (IEC 60851-5.2004, IDT)
GB/T 7672.1-2008 fiber covered winding wires - Part 1. Glass pack flat copper winding wire - General requirements (IEC 60317-0-4.
2006, IDT)
GB/T 7672.2 fiber covered winding wires - Part 2. 130 impregnated, bare copper flat wire and glass fiber covered enamelled copper flat wire
GB/T 7672.3 fiber covered winding wires - Part 3. 155 impregnated, bare copper flat wire and glass fiber covered enamelled copper flat wire (GB/T 7672.3-2008, IEC 60317-32.1990, IDT)
GB/T 7672.4 fiber covered winding wires - Part 4. 180 impregnated, bare copper flat wire and glass fiber covered enamelled copper flat wire (GB/T 7672.4-2008, IEC 60317-31.1990, IDT)
GB/T 7672.5 fiber covered winding wires - Part 5.200 impregnated, bare copper flat wire and glass fiber covered enamelled copper flat wire (GB/T 7672.5-2008, IEC 60317-33.1990, IDT)
3 Definitions, test methods and General Appearance
3.1 Overview
In addition to the definition of this part of GB/T 7672 provisions of, the other is defined in GB/T 7672.1-2008 in 3.1.
General test method see GB/T 7672.1-2008 in 3.2.
If GB/T 7672.1-2008 in this section are contradictory to this section shall prevail.
3.2 definitions
Define the maximum thickness of any thin plastic, the thickness is much smaller than its length and width, typically with rolls.
Note. The maximum thickness limit is generally several hundred microns.
......
This preview omits tables, figures, formulas and parts of the technical clauses. The complete document — 15 pages — is available in the English PDF.
Similar standards
Editions of GB/T 7672.6
| Edition | Title | Revision | Status |
|---|---|---|---|
| GB/T 7672.6-2008 | Glass-fiber wound winding wires - Part 6: Glass-fiber and film wound rectangular copper wire | current edition | Current |
| GB/T 7672.6-1987 | Glass-fiber wound winding wires - Part 6: Glass-fiber and film wound rectangular copper wire | previous edition | Superseded |
This page sells the current edition, GB/T 7672.6-2008. Earlier editions are listed for reference only.
How to Download GB/T 7672.6-2008
- 1
Add to cart
Click "Download PDF" on this page and choose "Buy this standard". You can add more standards before checkout.
- 2
Checkout
Enter your email and billing details. Payment is processed securely by Stripe (cards or bank transfer). Prefer bank details? Request a quotation (min. order $300).
- 3
Instant delivery (0–9 sec)
Delivery is automatic: within seconds of payment you'll receive an email with a secure download link. The link stays valid for 72 hours.
- 4
Invoice included
A tax invoice is attached to the confirmation email. Need a custom invoice? Contact us.
Related Standards
GB/T 7672.21-2008 — Glass-fiber wound winding wires -- Part 21: Glass-fiber wound round copper wire -- General requirements
GB/T 7672.5-2008 — Glass-fiber wound winding wires -- Part 5: Glass-fiber wound resin or varnish impregnated, bare or enamelled rectangular copper wire, temperature index 200
GB/T 7672.22-2008 — Glass-fiber wound winding wires -- Part 22: Glass-fiber wound resin or varnish impregnated, bare or enamelled round copper wire, temperature index 155
Secure payment via Stripe
Payments accepted
GB/T 7672.6-2008
$135.00