GB/T 4103.11-2012Methods for chemical analysis of lead and lead alloys - Part 11: Determination of zinc content (English PDF)
铅及铅合金化学分析方法 第11部分：锌量的测定
This is a limited preview
Buy now to download the full PDF (15 pages)
Need quotation for your management?
Get a formal quotation for GB/T 4103.11-2012 in 30 minutes.
Issued by
SAMR; SAC
Level / Type
National · Recommended
Issue date
December 31, 2012
Implementation date
October 1, 2013
Scope
GB/T 4103.11-2012 is the English-translated version of 铅及铅合金化学分析方法 第11部分：锌量的测定.
GB/T 4103.11-2012 is the Chinese standard "Methods for chemical analysis of lead and lead alloys - Part 11: Determination of zinc content". Its scope clause reads: This section GB/T 4103 provisions of the determination of lead and lead alloys of zinc content.
This section applies to the determination of lead ingots and lead alloys of zinc content. Its clauses include general; flame atomic absorption spectrometry.
Found what you need?
Document preview — GB/T 4103.11-2012
National Standard of the People's Republic of China
- ICS
- 77.120.60
- Classification
- H 13
- Replacing
- GB/T 4103.11-2000
Issued by: State Administration for Market Regulation; Standardization Administration of the PRC
Contents
- 1 Scope
- 2 Normative references
- 3 General
- 4 Flame Atomic Absorption Spectrometry
1 Scope
This section GB/T 4103 provisions of the determination of lead and lead alloys of zinc content.
This section applies to the determination of lead ingots and lead alloys of zinc content.
2 Normative references
The following documents for the application of this document is essential. For dated references, only the dated edition applies to this article
Member. For undated references, the latest edition (including any amendments) applies to this document.
GB/T 6682 analytical laboratory use specifications and test methods (ISO 3696)
GB/T 12806 laboratory glassware single marking flask (ISO 1042)
GB/T 12808 laboratory glassware single marking pipette (ISO 648)
GB/T 12809 Laboratory glassware Glass Container design and construction principles (ISO 384)
GB/T 12810 laboratory glassware gauge capacity calibration and use (ISO 4787)
3 General
3.1
Unless otherwise stated, the use of analytical reagent only recognized in the analysis; the water is distilled or deionized water or equivalent purity,
Shall comply with the provisions of GB/T 6682's.
3.2
instruments shall be within the test cycle, the performance indicators should meet the technical parameters required for verification; glass containers GB/T 12808,
GB/T 12809, A level, the specific use of GB/T 12806 requirements specified in reference to GB/T 12810 the experiment used containers are made
After soaking in dilute nitric acid, washed thoroughly with a water.
4 Flame Atomic Absorption Spectrometry
4.1 Determination of Range
Determination of zinc content in the range of 0.0003% to 0.050% (mass fraction).
4.2 Principle
Sample decomposition with nitric acid (when wZn < 0.0020 percent while that of lead generation lead sulfate precipitation), in a nitric acid medium, with air - acetylene fire
Flame atomic absorption spectrometer at a wavelength of 213.8nm, zinc measuring the absorbance when the sample contains a large amount of tin, antimony, adding EDTA, lemon
Citric acid, tartaric acid solubilization and prevent hydrolysis.
4.3 Reagents
4.3.1
tartaric acid.
4.3.2
citric acid.
......
This preview omits tables, figures, formulas and parts of the technical clauses. The complete document — 15 pages — is available in the English PDF.
Referenced standards
Similar standards
Editions of GB/T 4103.11
| Edition | Title | Revision | Status |
|---|---|---|---|
| GB/T 4103.11-2012 | Methods for chemical analysis of lead and lead alloys - Part 11: Determination of zinc content | current edition | Current |
| GB/T 4103.11-2000 | Methods for chemical analysis of lead and lead alloys - Part 11: Determination of zinc content | previous edition | Superseded |
This page sells the current edition, GB/T 4103.11-2012. Earlier editions are listed for reference only.
How to Download GB/T 4103.11-2012
- 1
Add to cart
Click "Download PDF" on this page and choose "Buy this standard". You can add more standards before checkout.
- 2
Checkout
Enter your email and billing details. Payment is processed securely by Stripe (cards or bank transfer). Prefer bank details? Request a quotation (min. order $300).
- 3
Instant delivery (0–9 sec)
Delivery is automatic: within seconds of payment you'll receive an email with a secure download link. The link stays valid for 72 hours.
- 4
Invoice included
A tax invoice is attached to the confirmation email. Need a custom invoice? Contact us.
Related Standards
GB/T 4103.1-2012 — Methods for chemical analysis of lead and lead alloys - Part 1: Determination of tin content
GB/T 4103.10-2012 — Methods for chemical analysis of lead and lead alloys - Part 10: Determination of silver content
GB/T 4103.12-2012 — Methods for chemical analysis of lead and lead alloys - Part 12: Determination of thallium content
Secure payment via Stripe
Payments accepted
GB/T 4103.11-2012
$125.00