Valid

GB/T 38494-2020Test method for impact resistance of ceramic wares (English PDF)

陶瓷器抗冲击试验方法

Preview PDF

This is a limited preview

Buy now to download the full PDF (15 pages)

Need quotation for your management?

Get a formal quotation for GB/T 38494-2020 in 30 minutes.

Issued by

SAMR; SAC

Level / Type

National · Recommended

Issue date

March 6, 2020

Implementation date

October 1, 2020

Scope

GB/T 38494-2020 is the English-translated version of 陶瓷器抗冲击试验方法.

GB/T 38494-2020 is the Chinese standard "Test method for impact resistance of ceramic wares". Its scope clause reads: This Standard specifies the test method for the impact resistance of ceramic wares.

This Standard is applicable to the impact test of the centre and edge of the bottom of the ceramic wares. Its clauses include terms and definitions; principle; apparatus and utensils; specimen; procedures; calculation formula; presentation of results; test report.

It was issued by the State Administration for Market Regulation on MARCH 06, 2020 and took effect on OCTOBER 01, 2020.

Found what you need?

Document preview — GB/T 38494-2020

National Standard of the People's Republic of China

ICS
81.060.20
Classification
Y 24

Issued by: State Administration for Market Regulation; Standardization Administration of the PRC

Contents

  • Foreword3
  • 1 Scope4
  • 2 Terms and Definitions4
  • 3 Principle4
  • 4 Apparatus and Utensils5
  • 5 Specimen5
  • 6 Procedures5
  • 7 Calculation Formula6
  • 8 Presentation of Results7
  • 9 Test Report7

1 Scope

This Standard specifies the test method for the impact resistance of ceramic wares.

This Standard is applicable to the impact test of the centre and edge of the bottom of the ceramic wares.

2 Terms and Definitions

For the purpose of this document, the following terms and definitions apply.

2.1 Impact energy

The energy that is required for generating cracks or breakage of ceramic wares.

2.2 Impact resistance

The impact energy (edge impact strength) or the square ratio of impact energy to thickness (centric impact strength) that is required for generating cracks or breakage of ceramic wares.

2.3 Centric position

The centre of the bottom of the ceramic wares.

2.4 Edge position

The position, when the bottom of the ceramic ware is placed flat on a plane, that the edge of the mouth is in contact with the pendulum.

3 Principle

The method, when the pendulum is released from a certain height to the lowest point, and the potential energy is converted into kinetic energy to impact the ceramic wares to cause cracks or breakage, which is used to characterize the impact resistance of the ceramic wares.

6 Procedures

6.1.3 Incremental test

Place the pendulum at the lowest energy position; release the pendulum to impact the specimen; block the pendulum with hand or other objects to avoid secondary impact; observe whether the specimen is cracked or damaged. Gradually increase the impact energy until the sample is cracked or damaged.

6.1.4 Results recording

Record the impact energy when cracks or breakage occur, and measure the thickness of the centric point of the specimen.

6.2 Edge impact test

6.2.1 Placement of the sample

The sample is placed flat on the fixed table and fixed; the pendulum is placed at the lowest point. And the sample fixed table is adjusted so that the impact point of the pendulum is at the thinnest and most prominent position of the edge of the specimen.

6.2.2 Fixed value test

Place the pendulum at a predetermined energy position; release the pendulum to impact the specimen; block the pendulum with hand or other objects to avoid secondary impact. Take out the specimen, and observe whether the specimen is cracked or damaged.

6.2.3 Incremental test

Place the pendulum at the lowest energy position; release the pendulum to impact the specimen; block the pendulum with hand or other objects to avoid secondary impact; observe whether the sample is cracked or damaged. Gradually increase the impact energy until the sample is cracked or damaged.

6.2.4 Results recording

Record the impact energy when cracks or breakage occur.

7 Calculation Formula

The calculation of impact resistance in the centric impact test is shown in Formula (1):

Where: […]

......
This preview omits tables, figures, formulas and parts of the technical clauses. The complete document — 15 pages — is available in the English PDF.

Similar standards

How to Download GB/T 38494-2020

  1. 1

    Add to cart

    Click "Download PDF" on this page and choose "Buy this standard". You can add more standards before checkout.

  2. 2

    Checkout

    Enter your email and billing details. Payment is processed securely by Stripe (cards or bank transfer). Prefer bank details? Request a quotation (min. order $300).

  3. 3

    Fast delivery

    After payment you'll receive an email confirmation. The English PDF is sent to the same address, usually within minutes and at the latest within 1 business day.

  4. 4

    Invoice included

    A tax invoice is attached to the confirmation email. Need a custom invoice? Contact us.

Related Standards

English PDF
15 pages
Fast delivery
Invoice included
View Cart

Secure payment via Stripe

Payments accepted

VisaMastercardAmerican ExpressApple PayGoogle PayStripe

GB/T 38494-2020

$85.00