Valid

GB/T 38390-2019Safety and control devices for gas burners and gas-burning appliances—Particular requirements—Pressure sensing device (English PDF)

燃气燃烧器和燃烧器具用安全和控制装置 特殊要求 压力传感装置

Preview PDF

This is a limited preview

Buy now to download the full PDF (22 pages)

Need quotation for your management?

Get a formal quotation for GB/T 38390-2019 in 30 minutes.

Issued by

SAMR; SAC

Level / Type

National · Recommended

Issue date

December 31, 2019

Implementation date

November 1, 2020

Scope

GB/T 38390-2019 is the English-translated version of 燃气燃烧器和燃烧器具用安全和控制装置 特殊要求 压力传感装置.

GB/T 38390-2019 is the Chinese standard "Safety and control devices for gas burners and gas-burning appliances—Particular requirements—Pressure sensing device".

Its scope clause reads: This standard specifies the terms and definitions for the use of pressure sensing devices for gas burners and combustion appliances as specified in GB/T 13611.

Class and grouping, structure and materials, requirements, test methods, inspection rules, marking, installation and operation instructions, packaging, transportation and storage.

This standard applies to the maximum inlet pressure of not more than 500kPa, used for gas water heaters, gas heating water heaters, gas burners/machines, Gas heaters, gas steam boxes, gas boilers and other gas burning appliances or combustion equipment that monitor the pressure of gas, air and flue gas Mechanical or electric pressure switch, pressure sensor with electronic sensing element. Its clauses include terms and definitions.

Found what you need?

Document preview — GB/T 38390-2019

National Standard of the People's Republic of China

ICS
91.140
Classification
P 45

Issued by: State Administration for Market Regulation; Standardization Administration of the PRC

Contents

  • Foreword III
  • 1 Scope
  • 2 Normative references
  • 3 Terms and definitions
  • 4 Classification and grouping
  • 4.1 Classification
  • 4.2 Group
  • 5 Structure and materials
  • 5.1 General requirements
  • 5.2 Structure
  • 5.3 Materials
  • 5.4 Connection
  • 5.5 Electronic Components of EPSD
  • 6 Requirement
  • 6.1 General requirements
  • 6.2 Component requirements
  • 6.3 Performance requirements
  • 7 Test method
  • 7.1 Test conditions
  • 7.2 Component tests
  • 7.3 Performance test
  • 8 Inspection rules
  • 8.1 Factory inspection
  • 8.2 Type test
  • 8.3 Evaluation and Verification
  • 9 Marking, installation and operating instructions
  • 9.1 Signs
  • 9.2 Installation and operating instructions
  • 9.3 Warnings
  • 10 Packaging, transport and storage
  • Appendix A (informative appendix) This standard supports the basic requirements of GB 16914-2012 Table
  • References

1 Scope

This standard specifies the terms and definitions for the use of pressure sensing devices for gas burners and combustion appliances as specified in GB/T 13611.

Class and grouping, structure and materials, requirements, test methods, inspection rules, marking, installation and operation instructions, packaging, transportation and storage.

This standard applies to the maximum inlet pressure of not more than 500kPa, used for gas water heaters, gas heating water heaters, gas burners/machines,

Gas heaters, gas steam boxes, gas boilers and other gas burning appliances or combustion equipment that monitor the pressure of gas, air and flue gas

Mechanical or electric pressure switch, pressure sensor with electronic sensing element.

2 Normative references

The following documents are essential for the application of this document. For dated references, only the dated version applies to this article

Pieces. For undated references, the latest version (including all amendments) applies to this document.

GB/T 1634 (all parts) Determination of deformation temperature of plastic load

GB/T 2828.1 Sampling inspection procedures for counts. Part 1. Sampling plan for batch inspections retrieved by acceptance quality limit (AQL)

GB/T 4208 enclosure protection grade (IP code)

GB/T 13611 Urban gas classification and basic characteristics

GB/T 14536.1-2008 Household and similar electrical automatic controllers Part 1. General requirements

GB/T 14536.7-2010 special requirements for pressure-sensitive electric automatic controllers for household and similar electric automatic controllers, including

Mechanical requirements

GB/T 15092.1-2010 Appliance switches Part 1. General requirements

GB/T 30597-2014 General requirements for safety and control devices for gas burners and combustion appliances

3 terms and definitions

The terms and definitions defined in GB/T 30597 and the following apply to this document.

3.1 Pressure sensing device pressuresensingdevice; PSD

A device that senses pressure and provides a signal, indicated by "PSD".

see picture 1.

3.2 Setpoint

Set PSD action pressure.

3.3 Switching pressure

Inlet pressure during PSD operation.

......
This preview omits tables, figures, formulas and parts of the technical clauses. The complete document — 22 pages — is available in the English PDF.

Referenced standards

Similar standards

How to Download GB/T 38390-2019

  1. 1

    Add to cart

    Click "Download PDF" on this page and choose "Buy this standard". You can add more standards before checkout.

  2. 2

    Checkout

    Enter your email and billing details. Payment is processed securely by Stripe (cards or bank transfer). Prefer bank details? Request a quotation (min. order $300).

  3. 3

    Fast delivery

    After payment you'll receive an email confirmation. The English PDF is sent to the same address, usually within minutes and at the latest within 1 business day.

  4. 4

    Invoice included

    A tax invoice is attached to the confirmation email. Need a custom invoice? Contact us.

Related Standards

English PDF
22 pages
Fast delivery
Invoice included
View Cart

Secure payment via Stripe

Payments accepted

VisaMastercardAmerican ExpressApple PayGoogle PayStripe

GB/T 38390-2019

$385.00