GB/T 36410.3-2018Energy consumption evaluation methods of port equipment—Part 3: Bridge type grab ship unloader (English PDF)
港口设备能源消耗评价方法 第3部分：桥式抓斗卸船机
This is a limited preview
Buy now to download the full PDF (15 pages)
Need quotation for your management?
Get a formal quotation for GB/T 36410.3-2018 in 30 minutes.
Issued by
SAMR; SAC
Level / Type
National · Recommended
Issue date
June 7, 2018
Implementation date
January 1, 2019
Scope
GB/T 36410.3-2018 is the English-translated version of 港口设备能源消耗评价方法 第3部分：桥式抓斗卸船机.
GB/T 36410.3-2018 is Part 3 of the Chinese series on evaluating the energy consumption of port equipment, and it deals with bridge-type grab ship unloaders for bulk cargo in ports.
It sets the test conditions: ambient temperature of 0 °C to 40 °C, relative humidity of no more than 95%, wind no stronger than force 5, grid voltage within -10% to +6% of the rated value, and an unloader that is certified, adjusted for energy efficiency and standing on rails inclined by no more than 2.5 per thousand.
It then gives the test method and the evaluation method, based on unit energy efficiency, the ratio of energy consumed to the mass of cargo unloaded in a standard cycle, with the test report form and the energy efficiency rating in the annexes. It was issued on 7 June 2018 and has applied since 1 January 2019.
Found what you need?
Document preview — GB/T 36410.3-2018
National Standard of the People's Republic of China
- ICS
- 53.020.20
- Classification
- R 46
Issued by: State Administration for Market Regulation; Standardization Administration of the PRC
Contents
- Foreword
- 1 Scope
- 2 Normative references
- 3 Terms and Definitions
- 4 Testing requirements
- 5 Detection method
- 6 Evaluation method
- Appendix A (Normative Appendix) Bridge Grab Ship Unloader Energy Efficiency Test Report
- Appendix B (normative appendix) Bridge grab ship unloader energy efficiency rating
Foreword
GB/T 36410 "Port Equipment Energy Consumption Evaluation Method" is divided into five parts.
--- Part 1. Shore container cranes;
--- Part 2. Orbital container gantry cranes;
--- Part 3. Bridge grab ship unloader;
--- Part 4. Bulk cargo shippers;
--- Part 5. Port tractors.
This part is the third part of GB/T 36410.
This part is drafted in accordance with the rules given in GB/T 1.1-2009.
1 Scope
This part of GB/T 36410 specifies the energy consumption testing requirements, testing methods and evaluation methods for bridge grab ship unloaders.
This section applies to the energy consumption evaluation of the bridge grab ship unloader for port loading and unloading bulk materials.
2 Normative references
The following documents are indispensable for the application of this document. For dated references, only dated versions apply to this document. For undated references, the latest edition (including all amendments) applies to this document.
Safety regulations for GB/T 18224 bridge grab ship unloader
GB/T 26475 Bridge grab ship unloader
GB/T 36410.1 Evaluation method for energy consumption of port equipment - Part 1.
3 Terms and definitions
The following terms and definitions as defined in GB/T 36410.1 apply to this document.
3.1 Unit energy efficiency
Under the standard cycle of the specified working conditions, the ratio of the energy consumption value to the total mass of the unloading cargo is the bridge grab ship unloader.
4 Testing requirements
4.1 Basic requirements
4.1.1 The ambient temperature should be 0 ° C ~ 40 ° C, the maximum relative humidity should not be greater than 95%.
4.1.2 The maximum wind speed should not exceed 5 levels.
4.1.3 The deviation of the grid input voltage fluctuation should be within the range of -10%~ 6% of the rated voltage, and the three-phase voltage unbalance rate should not be large. At 1.5%.
4.2 Tested ship unloader requirements
4.2.1 The normal operation of the bridge grab ship unloader (referred to as the ship unloader) shall comply with the relevant requirements of GB/T 18224 and GB/T 26475, The ship unloader parameters should be adjusted to improve energy efficiency.
4.2.2 The ship unloader shall be inspected by the competent department of the industry and have relevant certificates before the on-site energy consumption test can be carried out.
4.2.3 The ship unloader shall be on a flat rail surface with an inclination of not more than 2.5 per thousand.
4.3 Measuring instrument requirements
Measuring instruments should comply with the relevant provisions of GB/T 36410.1.
......
This preview omits tables, figures, formulas and parts of the technical clauses. The complete document — 15 pages — is available in the English PDF.
Referenced standards
Normative references
Similar standards
How to Download GB/T 36410.3-2018
- 1
Add to cart
Click "Download PDF" on this page and choose "Buy this standard". You can add more standards before checkout.
- 2
Checkout
Enter your email and billing details. Payment is processed securely by Stripe (cards or bank transfer). Prefer bank details? Request a quotation (min. order $300).
- 3
Instant delivery (0–9 sec)
Delivery is automatic: within seconds of payment you'll receive an email with a secure download link. The link stays valid for 72 hours.
- 4
Invoice included
A tax invoice is attached to the confirmation email. Need a custom invoice? Contact us.
Related Standards
GB/T 18224-2008 — Safety code for the bridge type grab ship unloader
GB/T 26475-2021 — Bridge type grab ship unloader
GB/T 36410.1-2018 — Energy consumption evaluation methods of port equipment—Part 1:Quayside container crane
Secure payment via Stripe
Payments accepted
GB/T 36410.3-2018
$145.00