GB/T 36410.4-2018Energy consumption evaluation methods of port equipment—Part 4: Bulk ship loader (English PDF)
港口设备能源消耗评价方法 第4部分：散货连续装船机
This is a limited preview
Buy now to download the full PDF (15 pages)
Need quotation for your management?
Get a formal quotation for GB/T 36410.4-2018 in 30 minutes.
Issued by
SAMR; SAC
Level / Type
National · Recommended
Issue date
June 7, 2018
Implementation date
January 1, 2019
Scope
GB/T 36410.4-2018 is the English-translated version of 港口设备能源消耗评价方法 第4部分：散货连续装船机.
GB/T 36410.4-2018 is Part 4 of the series on evaluating the energy consumption of port equipment and deals with bulk cargo ship loaders.
It sets the conditions for an on-site energy consumption test: ambient temperature, humidity, wind speed and grid voltage, the state of the ship loader, the slope of the site, the boom elevation angle and the measuring instruments.
It then gives the test method and the evaluation method, based on the unit energy efficiency, the ratio of the energy consumed to the total mass of cargo loaded under specified working conditions.
Normative annexes give the energy efficiency test report and the energy efficiency rating of bulk ship loaders. The general provisions come from Part 1, GB/T 36410.1. It was issued on 7 June 2018 and has applied since 1 January 2019.
Found what you need?
Document preview — GB/T 36410.4-2018
National Standard of the People's Republic of China
- ICS
- 53.040.99; 03.220.40
- Classification
- R 46
Issued by: State Administration for Market Regulation; Standardization Administration of the PRC
Contents
- Foreword
- 1 Scope
- 2 Normative references
- 3 Terms and Definitions
- 4 Testing requirements
- 5 Detection method
- 6 Evaluation method
- Appendix A (Normative Appendix) Energy Efficiency Test Report for Bulk Cargo Ships
- Appendix B (Normative Appendix) Bulk cargo shiploader energy efficiency rating
Foreword
GB/T 36410 "Port Equipment Energy Consumption Evaluation Method" is divided into five parts.
--- Part 1. Shore container cranes;
--- Part 2. Orbital container gantry cranes;
--- Part 3. Bridge grab ship unloader;
--- Part 4. Bulk cargo shippers;
--- Part 5. Port tractors.
This part is the fourth part of GB/T 36410.
This part is drafted in accordance with the rules given in GB/T 1.1-2009.
1 Scope
This part of GB/T 36410 specifies the energy consumption testing requirements, testing methods and evaluation methods for bulk cargo shippers.
This section applies to the energy consumption evaluation of bulk loading and unloading bulk cargo shippers.
2 Normative references
The following documents are indispensable for the application of this document. For dated references, only dated versions apply to this document. For undated references, the latest edition (including all amendments) applies to this document.
GB/T 36410.1 Evaluation method for energy consumption of port equipment - Part 1.
GB/T 36410.3-2018 Evaluation method for energy consumption of port equipment - Part 3. Bridge grab ship unloader
3 Terms and definitions
The following terms and definitions as defined in GB/T 36410.1 apply to this document.
3.1 Unit energy efficiency
The ratio of the energy consumption value to the total mass of the loaded cargo under the specified working conditions of the bulk cargo shiploader.
4 Testing requirements
4.1 Basic requirements
4.1.1 The ambient temperature should be 0 °C ~ 40 °C, the maximum relative humidity should not be greater than 95%.
4.1.2 The maximum wind speed should not exceed 5 levels.
4.1.3 The deviation of the grid input voltage fluctuation should be within the range of -10%~ 6% of the rated voltage, and the three-phase voltage unbalance rate should not be larger than 1.5%.
4.2 Tested ship loader requirements
4.2.1 The normal operation of the bulk cargo shiploader (referred to as the ship loader) shall comply with the relevant requirements of the ship loader and shall not be used to improve the loader's energy. Effectively adjust the ship loader parameters.
4.2.2 The ship loader shall be inspected by the competent department of the industry and have relevant certificates before the on-site energy consumption test can be carried out.
4.2.3 The slope of the site of the test fashion ship should not exceed 2.5 per thousand.
4.2.4 The elevation angle of the boom should be in the range of -3 ° ~ 3 °.
4.3 Measuring instrument requirements
Measuring instruments should comply with the relevant provisions of GB/T 36410.1.
......
This preview omits tables, figures, formulas and parts of the technical clauses. The complete document — 15 pages — is available in the English PDF.
Referenced standards
Similar standards
How to Download GB/T 36410.4-2018
- 1
Add to cart
Click "Download PDF" on this page and choose "Buy this standard". You can add more standards before checkout.
- 2
Checkout
Enter your email and billing details. Payment is processed securely by Stripe (cards or bank transfer). Prefer bank details? Request a quotation (min. order $300).
- 3
Instant delivery (0–9 sec)
Delivery is automatic: within seconds of payment you'll receive an email with a secure download link. The link stays valid for 72 hours.
- 4
Invoice included
A tax invoice is attached to the confirmation email. Need a custom invoice? Contact us.
Related Standards
GB/T 36410.1-2018 — Energy consumption evaluation methods of port equipment—Part 1:Quayside container crane
GB/T 36410.3-2018 — Energy consumption evaluation methods of port equipment—Part 3: Bridge type grab ship unloader
GB/T 36410.2-2018 — Energy consumption evaluation methods of port equipment—Part 2: Rail mounted container gantry crane
Secure payment via Stripe
Payments accepted
GB/T 36410.4-2018
$145.00