GB/T 31845-2015Mechanical structures for electrotechnical and electronic equipment—Thermal design specification (English PDF)
电工电子设备机械结构 热设计规范
This is a limited preview
Buy now to download the full PDF (37 pages)
Need quotation for your management?
Get a formal quotation for GB/T 31845-2015 in 30 minutes.
Issued by
SAMR; SAC
Level / Type
National · Recommended
Issue date
July 3, 2015
Implementation date
February 1, 2016
Scope
GB/T 31845-2015 is the English-translated version of 电工电子设备机械结构 热设计规范.
GB/T 31845-2015 is the Chinese standard "Mechanical structures for electrotechnical and electronic equipment—Thermal design specification".
Its scope clause reads: This standard specifies the basic principles of electrical and electronic equipment, machinery for thermal design, thermal design requirements, commonly used cooling technology, the key to cooling unit Parts, thermal interface materials and related requirements for thermal testing, and describes the physical parameters of the thermal design of algorithms and materials commonly used in the Appendix.
This standard applies to all electrical and electronic equipment thermal design of mechanical structures except handheld devices. The following electrical and electronic equipment referred to as "setting Preparation of "electrical and electronic equipment mechanical structure referred to as" mechanical structure. ". Its clauses include terms and definitions.
Found what you need?
Document preview — GB/T 31845-2015
National Standard of the People's Republic of China
- ICS
- 31.240
- Classification
- K 05
Issued by: State Administration for Market Regulation; Standardization Administration of the PRC
Contents
- Introduction
- 1 Scope
- 2 Normative references
- 3 Terms and definitions
- 4 Thermal Design Overview
- 4.5 accessible surface temperature for
- 4.9 redundant design
- 4.10 Other
- 5 commonly used cooling technology
- 5.1 Natural cooling
- 5.1.1 natural heat conduction in
- 5.1.2 natural heat convection
- 5.1.3 natural heat radiation in
- 5.1.4 Natural cooling heat transfer path control
- 5.2 Forced air cooling
- 5.2.1 duct design
- 5.2.2 fan selection, installation and speed control
- 5.2.3 Selection of the heat exchanger
- 5.2.4 Air Filter Selection
- 5.2.5 noise forced air cooling device control
- 5.2.6 Forced Air Cooling common main measures
- 5.3 Additional cooling technology
- 5.3.1 Liquid Cooling
- 5.3.2 Peltier
- 5.3.3 phase change thermal storage
- 6 heat management technology
- 6.1 Overview
- 6.2.1 Room plan
- 6.2.2 engine room cooling
- 6.2.3 engine room cooling mode selection
- 7 key components cooling and thermal interface material
- 7.1 radiator
- 7.1.1 The design of the radiator
- 7.1.1.1 radiator design process
- 7.1.1.2 General design requirements of the radiator
- 7.1.2 radiator installation requirements
- 7.2 heat pipe
- 7.2.1 Overview
- 7.2.3 choose to install the heat pipe
- 7.3 thermal interface material
- 7.3.1 Overview
- 7.3.2 performance thermal interface materials and parameters
- 7.3.2.1 Thermal conductivity
- 7.3.2.2 Thermal resistance
- 7.3.2.3 Continuous use temperature
- 7.3.2.4 hardness and compressibility
- 7.3.2.5 Breakdown Voltage
- 7.3.3 types of thermal interface materials
- 8 Thermal test
- 8.1 The purpose of thermal testing
- 8.3 Hot develop test programs
- 8.3.1 Test Environment
- 8.3.2 Select test point
- 8.4 Common Test Equipment
- 8.5 Installation position sensor
- 8.5.1 Test installation position of the device 29 when the surface temperature
- 8.5.2 installation location to test the air temperature at
- 8.5.4 Test installation position when the amplifier tube
- Appendix A (informative) Thermal design used in the calculation
- References
1 Scope
This standard specifies the basic principles of electrical and electronic equipment, machinery for thermal design, thermal design requirements, commonly used cooling technology, the key to cooling unit
Parts, thermal interface materials and related requirements for thermal testing, and describes the physical parameters of the thermal design of algorithms and materials commonly used in the Appendix.
This standard applies to all electrical and electronic equipment thermal design of mechanical structures except handheld devices. The following electrical and electronic equipment referred to as "setting
Preparation of "electrical and electronic equipment mechanical structure referred to as" mechanical structure. "
2 Normative references
The following documents for the application of this document is essential. For dated references, only the dated version suitable for use herein
Member. For undated references, the latest edition (including any amendments) applies to this document.
GB 3095 Ambient Air Quality Standard
GB 3096 acoustic environment quality standards
GB 4943.1-2011 Safety of information technology equipment - Part 1. General requirements
GB/T 14295-2008 Air Filter
YD/T 1821-2008 communications center room environmental conditions
ETS300119-5 equipment engineering; standard equipment for the European Telecommunications practical application; fifth part. Thermal Management (Environmental
Engineering (EE); EuropeanTelecommunicationStandardforEquipmentPractice; Part 5. Thermal
Management)
GR-63 Network Equipment Building System Requirements. Physical protection (NetworkEquipment-BuildingSystemRequire- ment. PhysicalProtection)
ASTMD54701) Standard Test Method (StandardTestMethodfor heat transfer characteristics of thermal conductivity of electrically insulating material
ThermalTransmissionPropertiesofThermalyConductiveElectricalInsulationMaterials)
1) ASTM. AmericanSocietyforTestingandMaterials, American Society for Testing and Materials.
3 Terms and Definitions
The following terms and definitions apply to this document.
3.1 Temperature gradient
Wait isothermal surface normal direction, temperature change amount per unit length.
3.2 Heat flow heattransferrate
Heat transfer unit of time on the road calories.
3.3 Thermal
Divided by the temperature difference between hot hot road traffic.
......
This preview omits tables, figures, formulas and parts of the technical clauses. The complete document — 37 pages — is available in the English PDF.
Similar standards
How to Download GB/T 31845-2015
- 1
Add to cart
Click "Download PDF" on this page and choose "Buy this standard". You can add more standards before checkout.
- 2
Checkout
Enter your email and billing details. Payment is processed securely by Stripe (cards or bank transfer). Prefer bank details? Request a quotation (min. order $300).
- 3
Fast delivery
After payment you'll receive an email confirmation. The English PDF is sent to the same address, usually within minutes and at the latest within 1 business day.
- 4
Invoice included
A tax invoice is attached to the confirmation email. Need a custom invoice? Contact us.
Related Standards
GB/T 10003-2026 — Biaxially oriented polypropylene (BOPP) film
GB/T 10004-2026 — Plastic/Plastic laminated films and pouches for packaging
GB/T 10007-2026 — Rigid cellular plastics - Determination of shear properties
GB/T 31845-2015
$570.00