Valid

GB/T 31471-2015General specification for metal foil for printed circuits (English PDF)

印制电路用金属箔通用规范

Preview PDF

This is a limited preview

Buy now to download the full PDF (17 pages)

Need quotation for your management?

Get a formal quotation for GB/T 31471-2015 in 30 minutes.

Issued by

SAMR; SAC

Level / Type

National · Recommended

Issue date

May 15, 2015

Implementation date

January 1, 2016

Scope

GB/T 31471-2015 is the English-translated version of 印制电路用金属箔通用规范.

GB/T 31471-2015 is the Chinese standard "General specification for metal foil for printed circuits".

Its scope clause reads: This standard specifies the printed circuit has a carrier (film or foil) support and unsupported supporting metal foil (hereinafter referred to as a metal foil) the identity of behalf No, the general technical requirements, quality assurance provisions, test methods, packaging, marking and storage and transportation requirements.

This standard applies to rigid, flexible printed circuit metal foil. Its clauses include terms and definitions.

Found what you need?

Document preview — GB/T 31471-2015

National Standard of the People's Republic of China

ICS
31.180
Classification
L 30

Issued by: State Administration for Market Regulation; Standardization Administration of the PRC

Contents

  • 1 Scope
  • 2 Normative references
  • 3 Terms and definitions
  • 4 metal foil identification code, type
  • 4.1 2 metal foil logo
  • 4.2 Code
  • 4.3 Model of the metal foil
  • 5 Requirements
  • 5.1 General
  • 5.2 General requirements
  • 5.3 Exterior
  • 5.4 Size
  • 5.5 Physical Performance Requirements
  • 5.6 process requirements
  • 5.7 Particular requirements for the metal foil
  • 6 Quality Assurance provisions
  • 9 6.1 Responsibility for Inspection
  • 6.2 test equipment and test equipment
  • 6.3 Test conditions
  • 6.4 Inspection classification
  • 6.5 Identification Test
  • 6.6 Quality conformance inspection
  • 7 13 test method
  • 7.1 Appearance
  • 7.2 Dimensions
  • 7.3 Physical Properties
  • 7.4 Process Performance
  • 7.5 Special Requirements
  • 8 packaging, labeling and transport storage
  • 8.1 Packaging
  • 8.2 mark
  • 8.3 Transport and storage
  • 9 order documents
  • References

1 Scope

This standard specifies the printed circuit has a carrier (film or foil) support and unsupported supporting metal foil (hereinafter referred to as a metal foil) the identity of behalf

No, the general technical requirements, quality assurance provisions, test methods, packaging, marking and storage and transportation requirements.

This standard applies to rigid, flexible printed circuit metal foil.

2 Normative references

The following documents for the application of this document is essential. For dated references, only the dated version suitable for use herein

Member. For undated references, the latest edition (including any amendments) applies to this document.

GB/T 2036 Printed Circuit Terminology

GB/T 8888 heavy non-ferrous metal processing products, packaging, labeling, transportation and storage

GB/T 29847-2013 Test method for copper foil for printed boards

3 Terms and Definitions

GB/T 2036 defined by the following terms and definitions apply to this document.

3.1 Elongation

When the specimen fracture under tensile load, the effective portion of the sample from the increment between the reticle and the reticle between the initial distance ratio, expressed as a percentage

FIG.

3.2 Tensile strength

When the specimen fracture under tensile load, maximum load ratio of the average cross-sectional area of the specimen.

3.3 Contour factor

The average total thickness of the metal foil, the thickness of the sample exceeds the amount specified by the actual mass per unit area of the metal foil and sample density calculations.

3.4 Profile of foilprofile

The processing and (or) enhanced adhesion treatment causes roughness of the metal foil surface.

3.5 Arithmetical mean deviation

Ra

In measuring length, from the centerline to the rough outline of the arithmetic mean of all absolute distances.

3.6

10.00 microscopic roughness height

Rz

In measuring length, five consecutive maximum peak-to-average distance between the trough.

......
This preview omits tables, figures, formulas and parts of the technical clauses. The complete document — 17 pages — is available in the English PDF.

Similar standards

How to Download GB/T 31471-2015

  1. 1

    Add to cart

    Click "Download PDF" on this page and choose "Buy this standard". You can add more standards before checkout.

  2. 2

    Checkout

    Enter your email and billing details. Payment is processed securely by Stripe (cards or bank transfer). Prefer bank details? Request a quotation (min. order $300).

  3. 3

    Fast delivery

    After payment you'll receive an email confirmation. The English PDF is sent to the same address, usually within minutes and at the latest within 1 business day.

  4. 4

    Invoice included

    A tax invoice is attached to the confirmation email. Need a custom invoice? Contact us.

Related Standards

English PDF
17 pages
Fast delivery
Invoice included
View Cart

Secure payment via Stripe

Payments accepted

VisaMastercardAmerican ExpressApple PayGoogle PayStripe

GB/T 31471-2015

$295.00