GB/T 29906-2013External thermal insulation composite systems based on expanded polystyrene (English PDF)
模塑聚苯板薄抹灰外墙外保温系统材料
This is a limited preview
Buy now to download the full PDF (25 pages)
Need quotation for your management?
Get a formal quotation for GB/T 29906-2013 in 30 minutes.
Issued by
SAMR; SAC
Level / Type
National · Recommended
Issue date
September 3, 2013
Implementation date
August 1, 2014
Scope
GB/T 29906-2013 is the English-translated version of 模塑聚苯板薄抹灰外墙外保温系统材料.
GB/T 29906-2013 is the Chinese standard "External thermal insulation composite systems based on expanded polystyrene".
Its scope clause reads: This standard specifies the terms and definitions molded polystyrene board thin plaster exterior insulation system materials, general provisions, requirements, test methods, inspection Inspection rules, product certification and instructions for use, packaging, transport and storage.
This standard applies to the molded polystyrene board thin plaster exterior insulation system materials used in civil construction. Its clauses include terms and definitions.
Found what you need?
Document preview — GB/T 29906-2013
National Standard of the People's Republic of China
- ICS
- 91.100.60
- Classification
- Q 25
Issued by: State Administration for Market Regulation; Standardization Administration of the PRC
Contents
- Introduction
- 1 Scope
- 2 Normative references
- 3 Terms and definitions
- 5 requires
- 6 Test methods
- 7 Inspection rules
- 8 product certification and instructions
- 9 packaging, transportation and storage
- Appendix A (informative) brick veneer molded polystyrene board thin plaster exterior insulation system materials
- Annex C (normative) fiberglass mesh alkali resistance rapid test method
1 Scope
This standard specifies the terms and definitions molded polystyrene board thin plaster exterior insulation system materials, general provisions, requirements, test methods, inspection
Inspection rules, product certification and instructions for use, packaging, transport and storage.
This standard applies to the molded polystyrene board thin plaster exterior insulation system materials used in civil construction.
2 Normative references
The following documents for the application of this document is essential. For dated references, only the dated version suitable for use herein
Member. For undated references, the latest edition (including any amendments) applies to this document.
GB/T 308 Rolling Ball
GB/T 3810.2-2006 Test methods of ceramic tiles - Part 2. Dimensions and surface quality inspection
GB/T 3810.3-2006 Test methods of ceramic tiles - Part 3. water absorption, apparent porosity, apparent relative density and bulk density
Determine
GB/T 3810.12-2006 Test methods of ceramic tiles Part 12. Determination of frost resistance
GB/T 6342 Determination of linear dimensions of foam rubber
GB/T 7689.5-2001 Reinforcements method for woven fabrics Part 5. Glass fiber tensile breaking strength and elongation at break
Length measurement
GB/T 8170-2008 revised value represents about rules and limit values and judgment
GB 8624-2012 Classification for burning behavior of building materials and products
GB/T 9914.3-2001 Test methods of enhancing Part 3. Determination of mass per unit area (idt ISO 3374.2000)
GB/T 10801.1 molded polystyrene foam for thermal insulation
GB/T 17146-1997 water vapor permeability test method of building materials
GB/T 17671 cement mortar strength test method (ISO method)
GB/T 20102-2006 fiberglass mesh alkali resistance test method for sodium hydroxide solution immersion
GB 50178-1993 Building Climate zoning standards
JC/T 547-2005 Ceramic Tile Adhesive
JC/T 1004-2006 Ceramic Tile grouts
JGJ110 decorative brick construction bond strength test
JGJ126 exterior wall construction and acceptance of decorative tile works
JGJ144 exterior insulation Technical specification
JG/T 366 with external insulation anchor
3 Terms and Definitions
The following terms and definitions apply to this document.
3.1
Molded polystyrene board thin plaster exterior insulation system externalthermalinsulationcompositesystemsbasedonex- pandedpolystyrene
Placed on the outside of buildings facades, with fixed primary wall insulation system bonding manner. System consists of a molded polystyrene board, adhesives, thick […]
......
This preview omits tables, figures, formulas and parts of the technical clauses. The complete document — 25 pages — is available in the English PDF.
Referenced standards
Cited by
- GB/T 30593-2025External wall interior insulation composite panel systems
- JG/T 532-2018Insulation board with surface-vitrified and expanded perlite for building
- JG/T 564-2018Fireproofing ceramic fiber boards for building
- JG/T 511-2017Foamed ceramic thermal insulation board in buildings
- JG/T 515-2017External thermal insulation systems based on phenolic foam panel
- JG/T 435-2014General specification of inorganic lightweight aggregate board for fireproof and insulation
Similar standards
How to Download GB/T 29906-2013
- 1
Add to cart
Click "Download PDF" on this page and choose "Buy this standard". You can add more standards before checkout.
- 2
Checkout
Enter your email and billing details. Payment is processed securely by Stripe (cards or bank transfer). Prefer bank details? Request a quotation (min. order $300).
- 3
Instant delivery (0–9 sec)
Delivery is automatic: within seconds of payment you'll receive an email with a secure download link. The link stays valid for 72 hours.
- 4
Invoice included
A tax invoice is attached to the confirmation email. Need a custom invoice? Contact us.
Related Standards
GB/T 10003-2026 — Biaxially oriented polypropylene (BOPP) film
GB/T 10004-2026 — Plastic/Plastic laminated films and pouches for packaging
GB/T 10007-2026 — Rigid cellular plastics - Determination of shear properties
Secure payment via Stripe
Payments accepted
GB/T 29906-2013
$435.00