GB/T 29001.4-2012Numerical control system of machine tool - Protocol specifications for NCUC-Bus fieldbus - Part 4: Application layer (English PDF)
机床数控系统 NCUC-Bus现场总线协议规范 第4部分:应用层
This is a limited preview
Buy now to download the full PDF (56 pages)
Need quotation for your management?
Get a formal quotation for GB/T 29001.4-2012 in 30 minutes.
Issued by
SAMR; SAC
Level / Type
National · Recommended
Issue date
December 31, 2012
Implementation date
July 1, 2013
Scope
GB/T 29001.4-2012 is the English-translated version of 机床数控系统 NCUC-Bus现场总线协议规范 第4部分:应用层.
GB/T 29001.4-2012 is the Chinese standard "Numerical control system of machine tool - Protocol specifications for NCUC-Bus fieldbus - Part 4: Application layer".
Its scope clause reads: GB/T 29001 specifies the CNC system NCUC-Bus Fieldbus (hereinafter referred to as NCUC-Bus) and basic data types Data transmission, communication protocols established NCUC-Bus for CNC machine tools and industrial automation and control processes prescribed specification.
This section GB/T 29001 specifies the CNC system NCUC-Bus application layer protocol specification. This section applies to CNC machine tools. Other uses of the NC system can refer to this section. Its clauses include terms and definitions, abbreviations.
Found what you need?
Document preview — GB/T 29001.4-2012
National Standard of the People's Republic of China
- ICS
- 25.040.20
- Classification
- J 50
Issued by: State Administration for Market Regulation; Standardization Administration of the PRC
Contents
- Introduction
- 1 Scope
- 2 Normative references
- 3 Terms and definitions, abbreviations
- 3.1 Terms and definitions
- 3.2 Acronyms
- 4 Architecture
- 5 Protocol Specification
- 5.1 Overview
- 5.2 Data Types
- 5.3 Communication Mode
- 5.4 bus state machine
- 6.1 Basic service
- 6.2 Communication preparation services
- 6.3 Control service running
- 6.4 Troubleshooting Service
- 6.5 Other Control Management Services
- 7 Application Layer frame format and data identifying
- 7.1 Overview
- 7.2 NCUC-Bus protocol network type specifies
- 7.3 NCUC-Bus Data Frame command word CM-ID format
- 7.4 NCUC-Bus communication data format
- 7.5 NCUC-Bus addressing and identification data frame
- 8 communication error detection and recovery
- 8.1 data error detection
- 8.2 Connecting fault detection
- 8.3 Error Correction
- 9 Commands
- 9.1 Overview
- 9.2 bus manager
- 9.4 lumped frame reader
- 9.5 running state data read and write
- 10 synchronization
- 10.1 Overview
- 10.2 Time Synchronization
- 10.3 Data synchronization
- 11 device data dictionary and standard equipment model
- Appendix A (informative) parameters Table
- References
1 Scope
GB/T 29001 specifies the CNC system NCUC-Bus Fieldbus (hereinafter referred to as NCUC-Bus) and basic data types
Data transmission, communication protocols established NCUC-Bus for CNC machine tools and industrial automation and control processes prescribed specification.
This section GB/T 29001 specifies the CNC system NCUC-Bus application layer protocol specification.
This section applies to CNC machine tools. Other uses of the NC system can refer to this section.
2 Normative references
The following documents for the application of this document is essential. For dated references, only the dated version suitable for use herein
Member. For undated references, the latest edition (including any amendments list) are applicable to this document.
GB/T 29001.1-2012 CNC system NCUC-Bus Fieldbus protocol specification - Part 1. General
Inter IEEEStd802.3-2005 IT system communication and information exchange between LAN and MAN special requirements of Part 3
Score. with collision detection Carrier Sense Multiple Access from (CSMA/CD) access method and physical layer specifications (Informationtechnology-Tele- communicationsandinformationexchangebetweensystems-Localandmetropolitanareanetworks-Specific requirements-Part 3. Carriersensemultipleaccesswithcolisiondetection (CSMA/CD) accessmethodand physicallayerspecifications)
3 Terms and definitions, abbreviations
3.1 Terms and Definitions
GB/T 29001.1-2012 and as defined in the following terms and definitions apply to this document.
3.1.1 Agreement protocol
The communication system for data exchange in the data format, error correction method and timing relationships conventions.
[GB/T 29001.1-2012, the definition 3.1.1]
3.1.2 Bus
Through time-multiplexed manner, information is transferred from one or more source components to one or more destination components of a set of transmission lines, is through
Communication system transmitting data in a common channel.
[GB/T 29001.1-2012, the definition 3.1.2]
3.1.3 Physical layer
In the ISO /OSI reference model the bottom communication is the foundation of the entire communication system. The physical layer is the data communication between devices mentioned
For transmission media and connected devices, to provide a reliable environment for data transmission, including the transmission medium (fiber optic, twisted pair, coaxial cable, etc.), the connection […]
......
This preview omits tables, figures, formulas and parts of the technical clauses. The complete document — 56 pages — is available in the English PDF.
Referenced standards
Similar standards
How to Download GB/T 29001.4-2012
- 1
Add to cart
Click "Download PDF" on this page and choose "Buy this standard". You can add more standards before checkout.
- 2
Checkout
Enter your email and billing details. Payment is processed securely by Stripe (cards or bank transfer). Prefer bank details? Request a quotation (min. order $300).
- 3
Fast delivery
After payment you'll receive an email confirmation. The English PDF is sent to the same address, usually within minutes and at the latest within 1 business day.
- 4
Invoice included
A tax invoice is attached to the confirmation email. Need a custom invoice? Contact us.
Related Standards
GB/T 29001.5-2013 — Numerical control system of machine tool—Protocol specifications for NCUC-Bus fieldbus—Part 5: Conformance testing
GB/T 29001.3-2012 — Numerical control system of machine tool - Protocol specifications for NCUC-Bus fieldbus - Part 3: Data link layer
GB/T 29001.2-2012 — Numerical control system of machine tool - Protocol specifications for NCUC-Bus fieldbus - Part 2: Physical layer
GB/T 29001.4-2012
$920.00