GB/T 26977-2011Test methods for the thermal performance of solar air collectors (English PDF)
太阳能空气集热器热性能试验方法
This is a limited preview
Buy now to download the full PDF (17 pages)
Need quotation for your management?
Get a formal quotation for GB/T 26977-2011 in 30 minutes.
Issued by
SAMR; SAC
Level / Type
National · Recommended
Issue date
July 19, 2011
Implementation date
August 1, 2012
Scope
GB/T 26977-2011 is the English-translated version of 太阳能空气集热器热性能试验方法.
GB/T 26977-2011 is the Chinese standard "Test methods for the thermal performance of solar air collectors". Its scope clause reads: This standard specifies the test methods and procedures to calculate the solar air collector thermal performance.
This standard applies to the use of only a single entrance and a single flat plate solar radiation heating outlet, transparent cover, heat the working fluid to air Solar air collector (hereinafter referred to as flat-plate collector), and a heat transfer working fluid is air non-condensing type all-glass vacuum tube type solar Can air collector (hereinafter referred to as the vacuum tube solar collector).
Its clauses include terms and definitions; symbols and units; collectors installed and the place.
Found what you need?
Document preview — GB/T 26977-2011
National Standard of the People's Republic of China
- ICS
- 27.160
- Classification
- F 12
Issued by: State Administration for Market Regulation; Standardization Administration of the PRC
Contents
- 1 Scope
- 2 Normative references
- 3 Terms and definitions
- 4 Symbols and units
- 5 collector installation and place
- 6 Instrumentation and Measurement
- 7 5 Test Bench
- 9 steady state efficiency - Flow Test
- 10 collector incidence angle correction factor
- 11 solar collector thermal performance test report
- Appendix A (normative) Symbols and units
- Annex B (informative) solar air collector thermal performance test report format
1 Scope
This standard specifies the test methods and procedures to calculate the solar air collector thermal performance.
This standard applies to the use of only a single entrance and a single flat plate solar radiation heating outlet, transparent cover, heat the working fluid to air
Solar air collector (hereinafter referred to as flat-plate collector), and a heat transfer working fluid is air non-condensing type all-glass vacuum tube type solar
Can air collector (hereinafter referred to as the vacuum tube solar collector).
2 Normative references
The following documents for the application of this document is essential. For dated references, only the dated version suitable for use herein
Member. For undated references, the latest edition (including any amendments) applies to this document.
GB 3100 International System of Units and Its Application
GB/T 4271 solar collector thermal performance test method
GB/T 12936 solar thermal terms
GB/T 19141 domestic solar water heating systems
JJG458 pyranometer
JJG1032 optical radiation measurement terms and definitions
ISO 9060 is used to measure the total solar radiation and direct radiation side volume meter technical requirements and classification (Solarenergy-
Specificationandclassificationofinstrumentsformeasuringhemisphericalsolaranddirectsolarradiation)
ISO 9488.1999 Solar term (Solarenergy-Vocabulary)
3 Terms and Definitions
GB 3100, GB/T 12936, GB/T 19141, JJG1032 and ISO 9488.1999 terms and definitions apply to this defined file.
4 Symbols and units
Symbols and units used in this standard is given in Appendix A.
5 collectors installed and the place
5.1 collector test stand
Collector test bench should not block the collector surface lighting, should not affect the back of the collector, the collector inlet and outlet sides and insulation protection temperature. Bench should open architecture, it does not affect the free flow of air along the surface of each collector. Minimum collector side from the ground should not be less
To 0.5m. When on the roof test bench distance from the edge of the roof should be more than 2m.
Collector test bench should be able to manually or automatically track the sun azimuth or elevation.
GB/T 33589-2026 | GB/T 29319-2024 | GB/T 33599-2017 | GB/T 26971-2011 | GB/T 26970-2011 | GB 26969-2011 | […]
......
This preview omits tables, figures, formulas and parts of the technical clauses. The complete document — 17 pages — is available in the English PDF.
Similar standards
How to Download GB/T 26977-2011
- 1
Add to cart
Click "Download PDF" on this page and choose "Buy this standard". You can add more standards before checkout.
- 2
Checkout
Enter your email and billing details. Payment is processed securely by Stripe (cards or bank transfer). Prefer bank details? Request a quotation (min. order $300).
- 3
Fast delivery
After payment you'll receive an email confirmation. The English PDF is sent to the same address, usually within minutes and at the latest within 1 business day.
- 4
Invoice included
A tax invoice is attached to the confirmation email. Need a custom invoice? Contact us.
Related Standards
GB/T 10003-2026 — Biaxially oriented polypropylene (BOPP) film
GB/T 10004-2026 — Plastic/Plastic laminated films and pouches for packaging
GB/T 10007-2026 — Rigid cellular plastics - Determination of shear properties
GB/T 26977-2011
$300.00