Valid

GB/T 2423.26-2008Environmental testing - Part 2: Test methods - Test Z/BM: Combined dry heat / low air pressure tests (English PDF)

Preview PDF

This is a limited preview

Buy now to download the full PDF (1976 pages)

Need quotation for your management?

Get a formal quotation for GB/T 2423.26-2008 in 30 minutes.

Issued by

Standardization Administration of China

Level / Type

National · Recommended

Issue date

December 30, 2008

Implementation date

October 1, 2009

Scope

GB/T 2423.26-2008 (Environmental testing - Part 2: Test methods - Test Z/BM: Combined dry heat / low air pressure tests) is available as an English-translated PDF.

GB/T 2423.26-2008 — This standard specifies thermal and non- thermal test sample temperature (temperature gradient or mutation) and low air pressure tests, see 8.

2. 2 and 8. 2. 8. Purpose of this test is to determine the components, equipment and other products for its storage and use of high temperatures encountered low pressure integrated environmental adaptability.

The comprehensive test is usually only a single environment in the test sample tests do not reveal the use of integrated environmental impact. Test procedures prescribed in this section apply only to the test temperature stabilization can be achieved during a test sample.

The test method specified in this section can only test a heat test sample. This test procedure is applicable to pressure greater than 1kPa pressure test. When the air pressure is less than or equal to 1kPa, the time to consider the contents of test procedures.

This section does not specify the height, pressure and temperature. See the special relationship between the three standards. GB/T 2423. 2 trial B test sample test for non- thermal and thermal contrast test sample test application guidance applicable to this section.

Note: The definition of non- heat test sample according to GB/T 2421 in the relevant regulations, should not be measured under low pressure hottest temperature. GB/T 2423.

Found what you need?

Document preview — GB/T 2423.26-2008

National Standard of the People's Republic of China

ICS: 19.040
Classification: K 04
Replacing: GB/T 2423.26-1992

Issued by: Standardization Administration of China

Introduction
1 Introduction
2 Objective
General Description 2
Test equipment 2
5 Severity levels
Pretreatment 3
7 Initial detection
8 3 test conditions
9 Intermediate detection
Recovery 10
11 Final inspection
Information given in the relevant specifications 12
Appendix NA (Informative Appendix) GB/T 2423 standard part
GB/T 2423.26-2008/IEC 60068-2-41.

Foreword

GB/T 2423.26 is Part 26 GB/T 2423 standard. Part of the GB/T 2423 standard, see informative Annex NA.

This section is equivalent to using the International Electrotechnical Commission IEC 60068-2-41. 1976 (first edition) "Basic environmental testing procedures - Part 2.

Test Test Z/BM. high temperature/low air pressure tests "(in English) and its amendments 1. 1983. For ease of use, make this part of the following series Series of Review.

--- To be consistent with the new IEC 60068 title name, the title of this section by the name of "Basic environmental testing procedures" to "electrical and electronic Environmental testing ";

--- "IEC 60068-2-41. 1976 this part" was changed to "GB/T 2423.26-2008 this section";

--- Remove the IEC 68-2-41. 1976 Foreword and Preface;

--- Increase the national standard foreword;

--- Increased the list of normative references the introductory phrase of the document; there is a reference to the correspondence between the national standards with international standards, and changes Order;

--- Increase the informative appendix "GB/T 2423 standard part" (see appendix NA).

This Part replaces GB/T 2423.26-1992 "electric and electronic products environmental testing procedures Test Z/BM. high temperature/low pressure Fully Making Test. " This section compared with the GB/T 2423.26-1992 main changes are as follows.

--- GB/T 2423.26-1992 reference to the International Electrotechnical Commission IEC 60068-2-41. 1976 (first edition) "Basic Environment Test procedures - Part 2. Tests - Test Z/BM. high temperature/low air pressure tests "(in English) and its amendments 1. 1983, this section is tantamount to the adoption;

--- Consistent with IEC original, this section in Figures 1 and 2 to Fig. 1a) and 1b), and placed in the body of the last;

--- Consistent with IEC original format is prepared, this section 4.1.1 and 4.1.2 combined; and 5.1.3 combined 5.1.1,5.1.2 and together; 8.1.1 and 8.1.2 combined;

--- This part is not listed in Table 1 and the temperature, pressure corresponding to the height values, see the relationship between the three specific standards; an increase in mbar the pressure value unit; and changed the last two rows along the row of parameters;

It does not require temperature control during this part --- 8.2.8 pressure.

Appendix NA This section is informative appendix.

This part of the National Electrical and Electronic Products Environmental conditions and environmental tests for Standardization Technical Committee (SAC/TC8) and focal points.

This section is drafted. Guangzhou Electric Apparatus Research Institute.

1 Introduction

1.1 Overview

GB/T 2423 This section is about the thermal and non-thermal test sample temperature (temperature gradient or mutations) and low air pressure tests, see 8.2.2 and 8.2.8.

Purpose of this test is to determine the high-temperature components, equipment and other products encountered in their storage and use - low air pressure environments suitable Atopic.

The comprehensive test is usually only a single test sample used for environmental testing can not reveal the integrated environmental impact. Provisions of this Part Test procedure applies only during the test to achieve a stable temperature of the test sample.

Test methods specified in this standard can only test a heat test sample.

1.2 Low pressure

This test procedure is applicable to pressures greater than 1kPa the pressure test. When the pressure is less than or equal to 1kPa, time to consider the test program Content.

This section does not specify the relationship between height, pressure and temperature. See the special relationship between the three standards.

1.3 Temperature

1.3.1 GB/T 2423.2 guidance regarding the test sample B test test test test sample heat radiating and non-application of contrast apply to this section.

Note. The definition of a non-heat test samples according to the GB/T 2421 regulations, not to measure the hottest temperature at low pressure.

1.3.2 GB/T 2423.2 Test B thermal test sample should be tested in the absence of priority forced air circulation in the chamber.

1.4 Normative References

The following documents contain provisions which, through reference to GB/T 2423 to the present, constitute provisions of this section. For dated reference documents Member, all subsequent amendments (not including errata content) or revisions do not apply to this section, however, encouraged to reach under this section Parties to research agreement to use the latest versions of these documents. For undated reference documents, the latest versions apply to this section.

GB/T 2421 Environmental testing for electric and electronic products - Part 1. General (GB/T 2421-1999, idt IEC 60068-1. 1988) GB/T 2423.2 Electrical and Electronic Products Environmental Testing Part 2. Test methods Test B. Dry heat (GB/T 2423.2-2008, IEC 68-2-2:2007, IDT) GB/T 2423.21 Environmental testing for electric and electronic products Part 2. Test methods - Test M. Low air pressure (GB/T 2423.21-2008, IEC 68-2-13. 1983, IDT) GB/T 2423.22 Environmental testing for electric and electronic products Part 2. Test methods - Test N. temperature changes (GB/T 2423.22-2002, IEC 68-2-14. 1984, IDT) 1) GB/T 2424.1 electric and electronic products environmental testing high temperature and low temperature tests (GB/T 2424.1-2005, IEC 60068-3-1. 1974, IDT)

1) IEC 60068-2-41 referenced file is not listed in the standard, but the text references, see Note 8.2.2.

GB/T 2424.15 electric and electronic products environmental testing procedures for temperature/low air pressure tests Guide (GB/T 2424.15-2008, IEC 68-3-2. 1976, IDT) GB/T 2423.26-2008/IEC 60068-2-41. 1976

......
This preview omits tables, figures, formulas and parts of the technical clauses. The complete document — 1976 pages — is available in the English PDF.

Referenced standards

Normative references

GB/T 2423 · IEC 60068 · IEC 68

Cited by

How to Download GB/T 2423.26-2008

1
Add to cart
Click "Download PDF" on this page and choose "Buy this standard". You can add more standards before checkout.
2
Checkout
Enter your email and billing details. Payment is processed securely by Stripe (cards or bank transfer). Prefer bank details? Request a quotation (min. order $300).
3
Instant delivery (0–9 sec)
Delivery is automatic: within seconds of payment you'll receive an email with a secure download link. The link stays valid for 72 hours.
4
Invoice included
A tax invoice is attached to the confirmation email. Need a custom invoice? Contact us.