GB/T 24109-2009CNC engraving and milling machine (English PDF)
数控雕铣机
This is a limited preview
Buy now to download the full PDF (29 pages)
Need quotation for your management?
Get a formal quotation for GB/T 24109-2009 in 30 minutes.
Issued by
SAMR; SAC
Level / Type
National · Recommended
Issue date
June 12, 2009
Implementation date
December 1, 2009
Scope
GB/T 24109-2009 is the English-translated version of 数控雕铣机.
GB/T 24109-2009 specifies the technical requirements, test methods and inspection rules for CNC engraving and milling machines. Clause 1 applies it to gantry CNC engraving and milling machines, referred to thereafter as the product, and adds that other forms of CNC engraving and milling machine and CNC engraving machines may also refer to it.
The table of contents runs Scope, Normative references, Terms and definitions, Technical requirements, Test method and Inspection rules, followed by two informative annexes, one on the approximate calculation and testing of the maximum torque of the machine tool main drive and one on the testing and approximate calculation of the maximum cutting resistance of the machine.
Clause 2 cites GB 5226.1, GB/T 6576, GB/T 7932, GB/T 9061-2006, GB 15760, GB/T 16769-1997, GB/T 17421.1-1998, GB/T 17421.2-2000, GB/T 19449.1-2004, GB/T 19449.2-2004 and JB/T 8832.
Clause 3 holds five definitions whose term names the draft does not print: a CNC machine tool with both engraving and milling capability; such a machine able to cut at high intensity; such a machine whose maximum NC feed rate is not less than 15 m/min; such a machine fitted with an automatic tool changer (ATC); and such a machine fitted with an ATC and having a maximum NC feed rate of not less than 15 m/min.
The foreword states that the standard was proposed by the China National Light Industry Council, that it falls under the national light industry machinery standardization technical committee, and that Appendices A and B are informative.
The draft text stops at the end of clause 3, so the technical requirement, test and inspection clauses are not shown. It was issued on 2009-06-12 and has applied since 2009-12-01.
Found what you need?
Document preview — GB/T 24109-2009
National Standard of the People's Republic of China
- ICS
- 25.040.20
- Classification
- J 54
Issued by: State Administration for Market Regulation; Standardization Administration of the PRC
Contents
- Introduction
- 1 Scope
- 2 Normative references
- 3 Terms and definitions
- 4 2 Technical Requirements
- 5 Test Method
- 6 Inspection Rules
- Appendix A (informative) machine tool main drive of the maximum torque and approximate calculation tests
- Annex B (informative) Maximum cutting resistance testing machine and approximate calculation method
Foreword
Appendix A of this standard and Appendix B is an informative annex.
The standard proposed by China National Light Industry Council.
This standard by the National Light Industry Machinery Standardization Technical Committee.
1 Scope
This standard specifies the technical requirements, test methods and inspection rules CNC milling machine.
This standard is applicable to gantry CNC milling machine (hereinafter referred to as the product), other forms of CNC engraving and milling machine, CNC engraving machine can also refer use.
2 Normative references
The following documents contain provisions which, through reference in this standard and become the standard terms. For dated references, subsequent Amendments (not including errata content) or revisions do not apply to this standard, however, encourage the parties to the agreement are based on research Whether the latest versions of these documents. For undated reference documents, the latest versions apply to this standard.
GB 5226.1 Safety of machinery electrical equipment Part 1: General requirements
GB/T 6576 machine lubrication system
GB/T 7932 General technical conditions of pneumatic systems
GB/T 9061-2006 General technical conditions for metal cutting machine tools
GB 15760 metal cutting machine tool safety general technology condition
GB/T 16769-1997 Metal-cutting machine noise level measurements
GB/T 17421.1-1998 Test code for machine tools - Part 1: under no-load or finishing conditions Geometric accuracy of machines
GB/T 17421.2-2000 Test code for machine tools - Part 2: CNC axis positioning accuracy and repeatability of determination
GB/T 19449.1-2004 interfaces - Part 1 hollow cone with a flange contact surface: shank - Size
GB/T 19449.2-2004 Part 2 with flange contact surface of a hollow cone interfaces: mounting holes - Size
JB/T 8832 CNC system General technical conditions
3 Terms and Definitions
The following terms and definitions apply to this standard.
3.1
Both engraving and milling capacity of CNC machine tools.
3.2
Capable of high-intensity cutting CNC milling machine.
3.3
The maximum feed rate of not less than NC 15m/min for engraving and milling machine.
3.4
CNC with automatic tool changer (ATC) of the engraving and milling machine.
3.5
Equipped with automatic tool changer (ATC), and the maximum feed rate of not less than NC 15m/min for engraving and milling machine.
......
This preview omits tables, figures, formulas and parts of the technical clauses. The complete document — 29 pages — is available in the English PDF.
Referenced standards
Normative references
- GB 5226.1Electrical safety of machinery - Electrical equipment of machines - Part 1: General requirements
- GB/T 6576Machine tool -- Lubrication systems
- GB/T 7932Pneumatic fluid power -- General rules and safety requirements for systems and their components
- GB/T 9061-2006Metal-cutting machine tools - General specifications
- GB 15760Metal cutting machines - General specifications for safeguarding
- GB/T 16769-1997Metal-cutting machine tools -- Measurement method of sound pressure level
Similar standards
How to Download GB/T 24109-2009
- 1
Add to cart
Click "Download PDF" on this page and choose "Buy this standard". You can add more standards before checkout.
- 2
Checkout
Enter your email and billing details. Payment is processed securely by Stripe (cards or bank transfer). Prefer bank details? Request a quotation (min. order $300).
- 3
Fast delivery
After payment you'll receive an email confirmation. The English PDF is sent to the same address, usually within minutes and at the latest within 1 business day.
- 4
Invoice included
A tax invoice is attached to the confirmation email. Need a custom invoice? Contact us.
Related Standards
GB 15760-1995 — Metal-cutting machine tools--General safeguarding specification
GB 15760-2004 — Metal-cutting machine tools - General safeguarding specification
GB 15760-2025 — Metal cutting machines - General specifications for safeguarding
GB/T 24109-2009
$435.00