Valid

GB/T 23568.1-2009Reliability evaluation for function units of machine tools - Part 1: General rule (English PDF)

机床功能部件可靠性评定第1部分：总则

Preview PDF

This is a limited preview

Buy now to download the full PDF (15 pages)

Need quotation for your management?

Get a formal quotation for GB/T 23568.1-2009 in 30 minutes.

Issued by

SAMR; SAC

Level / Type

National · Recommended

Issue date

April 13, 2009

Implementation date

January 1, 2010

Scope

GB/T 23568.1-2009 is the English-translated version of 机床功能部件可靠性评定第1部分：总则.

GB/T 23568.1-2009 is the Chinese standard "Reliability evaluation for function units of machine tools - Part 1: General rule".

Its scope clause reads: This section GB/T 23568 specifies the failure criterion machine tool components when performing reliability assessment, principles of sampling, testing The method of data processing, the results of the assessment of the total requirement.

This section applies to ball screws, linear guides, mechanical spindle unit, spindle, tool magazine and automatic tool exchange device, the number of Reliability assessment of machine tool components controlled turret, CNC turret, chip conveyor, protective devices (hereinafter referred to as features) products.

All kinds of features can be added preparation of the corresponding product reliability evaluation method based on the principles and requirements of this section.

Other features product implementation. Its clauses include terms and definitions.

Found what you need?

Document preview — GB/T 23568.1-2009

National Standard of the People's Republic of China

ICS: 25.060.10
Classification: J 51

Issued by: State Administration for Market Regulation; Standardization Administration of the PRC

Introduction
1 Scope
2 Normative references
3 Terms and definitions
4 2 General requirements
5 failure determination Principle
7 Test mode
8 Test Content
9 test requirements
10 Fault monitoring and recording
11 Reliability Evaluation Index
12 results found
Appendix A (informative) reliability test run record
Annex B (informative) Reliability Test Fault Record
Annex C (informative) Failure Analysis Report

1 Scope

This section GB/T 23568 specifies the failure criterion machine tool components when performing reliability assessment, principles of sampling, testing

The method of data processing, the results of the assessment of the total requirement.

This section applies to ball screws, linear guides, mechanical spindle unit, spindle, tool magazine and automatic tool exchange device, the number of

Reliability assessment of machine tool components controlled turret, CNC turret, chip conveyor, protective devices (hereinafter referred to as features) products.

All kinds of features can be added preparation of the corresponding product reliability evaluation method based on the principles and requirements of this section.

Other features product implementation.

2 Normative references

The following documents contain provisions which, through reference GB/T 23568 in this section constitute provisions of this section. For dated reference documents

Member, all subsequent amendments (not including errata content) or revisions do not apply to this section, however, encouraged to reach under this section

Parties to research agreement to use the latest versions of these documents. For undated reference documents, the latest versions apply to this section.

GB/T 3187-1994 reliability, maintainability terms

3 Terms and Definitions

GB/T 3187 and established the following terms and definitions apply to this part of the GB/T 23568 of.

3.1

A function of machine tool parts.

3.2

Loss of functionality or performance of a predetermined index exceeds a predetermined limit state and events.

[GB/T 3187-1994,4.2.1]

3.3

Or work in the interpretation of test results must be included in the calculation of the reliability values at or fault. Guidelines should be included in the regulations.

[GB/T 3187-1994,4.1.13]

3.4

Or in the interpretation of the test results of the work or the reliability of the calculation values should be excluded faults.

[GB/T 3187-1994,4.1.14]

3.5

The average working time between two adjacent faults.

......
This preview omits tables, figures, formulas and parts of the technical clauses. The complete document — 15 pages — is available in the English PDF.

Referenced standards

Cited by

Similar standards

GB/T 39983-2021|GB/T 20959-2025|GB/T 20960-2025|GB/T 39954-2021|GB/T 39961-2021|GB/T 35094-2018

How to Download GB/T 23568.1-2009

1
Add to cart
Click "Download PDF" on this page and choose "Buy this standard". You can add more standards before checkout.
2
Checkout
Enter your email and billing details. Payment is processed securely by Stripe (cards or bank transfer). Prefer bank details? Request a quotation (min. order $300).
3
Instant delivery (0–9 sec)
Delivery is automatic: within seconds of payment you'll receive an email with a secure download link. The link stays valid for 72 hours.
4
Invoice included
A tax invoice is attached to the confirmation email. Need a custom invoice? Contact us.